relay DODGE RAM 1999 Service Workshop Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 314 of 1691
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external voltmeter, measure voltage between ground and
CTM 18-pin connector C2 terminal No. 18 (Black/Red wire). If voltage
is more than 9.5 volts, replace CTM. If voltage is 9.5 volts or less,
repair open in Black/Red wire between CTM and horn relay.
6) Remove security relay from Power Distribution Center
(PDC). Turn ignition on. Connect a test light between battery source
and headlight relay connector terminal No. 85 (Red/Dark Blue wire).
Using scan tool, actuate relay. If test light illuminates, replace
security relay. If test light does not illuminate, go to next step.
7) Using an external voltmeter, measure voltage between
battery voltage and security relay connector terminal No. 86
(Red/Orange wire). If voltage is more than 9.5 volts, go to next step.\
If voltage is 9.5 volts or less, repair open in Red/Orange wire
between battery source and security relay.
8) Reinstall security relay. Locate Central Timer Module
(CTM). CTM is located behind right kick panel. Disconnect CTM 18-pin
connector C2. Using an external voltmeter, measure voltage between
ground and CTM 18-pin connector C2 terminal No. 6 (Red/Dark Blue
wire). If voltage is more than 9.5 volts, replace CTM. If voltage is
9.5 volts or less, repair open in Red/Dark Blue wire between CTM and
security relay.
9) Disconnect overhead console 12-pin connector. Using an
external voltmeter, measure voltage between battery and overhead
console 12-pin connector terminal No. 11 (Black wire). Using scan
tool, actuate VTSS indicator light. If voltage is about 10 volts,
replace overhead console. If voltage is not about 10 volts, go to next
step.
10) Measure voltage between ground and overhead console 12-
pin connector terminal No. 5 (Pink wire). Turn ignition on. If voltage\
is more than 10 volts, go to next step. If voltage is 10 volts or
less, repair open Pink wire.
11) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external ohmmeter, measure resistance between ground and
CTM 18-pin connector C2 terminal No. 8 (Black wire). If resistance is
5 ohms or more, replace CTM. If resistance is less than 5 ohms, repair
open Black wire between CTM and VTSS indicator light.
12) Using scan tool, place VTSS in diagnostic mode and follow
directions on screen. If TURN KEY TO ACC POSITION is not displayed, go
to step 24). If NO RESPONSE after turning key to accessory position or
TURN KEY TO ACC POSITION is displayed longer than 15 seconds, go to
next step. If neither response is received, go to step 14).
13) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Gain access to CTM 18-pin connector C2. Ensure key
is in accessory position. Using an external voltmeter, measure voltage
between ground and backprobe of CTM 18-pin connector C2 terminal No. 5
(Dark Blue/White wire). If voltage is more than 10 volts, replace CTM.\
If voltage is 10 volts or less, repair open Dark Blue/White wire
between CTM and junction block.
14) Remove key from ignition. Wait 2 seconds after performing
each of the following actions. Open, then close both door. Operate
power door lock switch to lock, then unlock position. Rotate key both
directions in both doors. Ensure each operation is successful. If any
operation is unsuccessful, see VTSS SYMPTOM DIRECTORY table for repair
of failed operation. If all operations are successful, go to step 22).
VTSS SYMPTOM DIRECTORY
\
\
\
\
\
\
\
Problem Circuit Go To
Driver's Door Open Or Close ............................... Step 15)
Page 316 of 1691
disarm switch state CLOSED, replace CTM.
23) Turn ignition switch to START position. If horn does not
sound, go to next step. If horn sounds, go to step 24).
24) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 14-pin connector C1. Using an
external voltmeter, measure voltage between ground and CTM 14-pin
connector C1 terminal No. 8 (Dark Blue/White wire). If voltage is more\
than 10 volts, replace CTM. If voltage is 10 volts or less, repair
open Dark Blue/White wire between CTM and RUN-ACC fuse in junction
block.
WINDSHIELD WIPER SYSTEM
WIPER PARK SWITCH FAILURE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
NOTE: It takes 8 seconds for wiper park switch failure DTC to set.
1) Using scan tool, clear DTCs. See appropriate SELF-
DIAGNOSTICS article. Operate wipers in low speed, then intermittent
mode. Reread DTCs. If WIPER PARK SWITCH FAILURE is displayed, go to
next step. If WIPER PARK SWITCH FAILURE is not displayed, system is
currently functioning properly.
2) Gain access to wiper motor connector. Using an external
voltmeter, measure voltage between ground and wiper motor terminal No.
2 (Dark Green wire). If voltage is more than 9 volts, go to next step.\
If voltage is 9 volts or less, replace wiper motor.
3) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). If voltage is 9 volts or less,
replace CTM. If voltage is more than 9 volts, repair short to voltage
in Dark Green wire between CTM and wiper relay or wiper motor.
INTERMITTENT WIPERS INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select CENTRAL TIMER MODULE. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) If problem is wipers parking in wrong position, go to next
step. If problem is not wipers parking in wrong position, go to step
5).
3) Gain access to wiper motor connector. Turn wipers on to
low speed. Using an external voltmeter, measure voltage between ground
and wiper motor switch terminal No. 2 (Dark Green wire). If voltage
does not cycle between zero and 12 volts, replace wiper motor. If
voltage cycles between zero and 12 volts, go to next step.
Page 317 of 1691
4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). Wipers should be operating at low
speed. If voltage does not cycle between zero and 12 volts, repair
open Dark Green wire between CTM and wiper relay or wiper motor. If
voltage cycles between zero and 10 volts, replace CTM.
5) Using scan tool, monitor intermittent wiper voltage level.
Rotate wiper switch from low intermittent to high intermittent level.
If voltage changes from approximately 2.5 to 12 volts, replace CTM. If
voltage does not change from approximately 2.5 to 12 volts, go to next
step.
6) Disconnect 24-pin multifunction switch connector. Using an
external ohmmeter, measure resistance of White/Dark Blue wire between
multifunction switch connector terminal No. 1 and CTM 14-pin Green
connector C1 terminal No. 12. if resistance is less than 5 ohms,
replace multifunction switch. If resistance is 5 ohms or more, repair
open White/Dark Blue wire between multifunction switch and CTM.
NO WIPER ACTUATION AFTER WASH BUTTON PUSHED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central Timer Module (CTM). If sca\
n
tool displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) Turn ignition on. If washer system works, go to next step.
If washer system does not work, see appropriate WIPER/WASHER SYSTEMS
article.
3) Using scan tool, actuate washer. If washer pump sense
displays ON, replace CTM. If washer pump sense does not display ON,
repair open Brown wire between CTM 14-pin connector C1 terminal No. 10
and multifunction switch.
WIPER SPEED SENSITIVE FEATURE INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central timer module (CTM). If sca\
n
tool display is not blank or have a CCD bus failure message, go to
next step. If scan tool display is blank or has a CCD bus failure
message, see appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select Powertrain Control Module (PCM).
If scan tool display is not blank or have a CCD bus failure message,
go to next step. If scan tool display is blank or has a CCD bus
failure message, see appropriate VEHICLE COMMUNICATIONS article.
3) Raise and support vehicle. Turn wipers on to lowest
intermittent position. Time interval between wipes. Spin rear wheels
to more than 15 MPH. If interval between wipes decreased to
approximately 18 seconds, system is currently functioning properly. If
interval between wipes did not decrease to approximately 18 seconds,
Page 319 of 1691
* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS
Page 340 of 1691
missing ................ C .. Require replacement of missing
parts.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
(1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
PADS
See FRICTION MATERIAL .
PEDAL TRAVEL SWITCHES
See SWITCHES.
PEDALS
See BRAKE PEDALS.
POWERMASTER
See HYDRO-BOOSTERS .
PUMPS
See ELECTRICAL PUMPS AND MOTORS .
PRESSURE DIFFERENTIAL SWITCHES
See SWITCHES.
PRESSURE SWITCHES
See SWITCHES.
RELAYS
NOTE: Copied from Electrical UIGs
RELAY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Housing broken .......... A ............ Require replacement.
Housing cracked ......... 2 ............ Suggest replacement.
Inoperative ( 1) ......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned,
affecting performance .. A ........... ( 2) Require repair or
replacement.
Page 367 of 1691
CLU TC H
1999 D odge P ic ku p R 1500
1998-99 CLUTCHES
CHRY - RWD - Trucks
Dakota, Ram Pickup
DESCRIPTION
Clutches on all models are dry, single-disc design.
Adjustment for wear is not possible. Clutch pedal is connected to
release fork through a hydraulic master cylinder and slave cylinder
and is not adjustable. Pre-lubricated clutch bearing is constant
running type. External adjustments cannot be made.
All models are equipped with a clutch pedal position switch.
The switch completes the circuit to the starter relay and is mounted
on clutch master cylinder push rod. The position switch is an integral
part of clutch master cylinder push rod and cannot be serviced
separately.
TRANSMISSION/TRANSFER CASE APPLICATION
\
\
\
\
\
\
\
Transmission Transfer Case
Dakota
AX15, NV1500 & NV3500 .............................. NV231 & NV242
Ram Pickup
NV3500, NV4500, NV4500HD & NV5600 ..... NV231HD, NV241LD & NV241HD
\
\
\
\
\
\
\
ADJUSTMENTS
CLUTCH PEDAL FREE PLAY
NOTE: Clutches are a single, dry disc type. Adjustment for wear is
not possible. Clutch is actuated through hydraulic master
cylinder and slave cylinder, and is self-adjusting.
SHIFT LINKAGE ADJUSTMENT
NV231 (Dakota)
1) Shift transfer case into 4H position, and secure shift
lever in shift gate. See Fig. 1. Raise and support vehicle. Loosen
shift rod lock bolt at swivel. Ensure shift rod slides freely in
adjusting swivel.
2) Ensure transfer case range lever is in 4H position. Slide
adjusting swivel forward until shift rod contacts shift gate
crossover, then slide adjusting swivel back, allowing a .11-.20" (3-5
mm) gap between shift lever and shift gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m.). Lower vehicle, making sure all
wheels are off floor. Start engine. Shift transfer case through all
ranges to verify correct adjustment.
NV231HD, NV241LD & NV241HD (Ram Pickup)
1) Place shift lever into 2H position. Raise and support
vehicle. Loosen shift rod lock bolt at swivel. See Fig. 2. Ensure
shift rod fits in swivel and does not bind.
2) Ensure transfer case shift lever is in 2H position. Lower
vehicle. Position shift lever in cab so distance between instrument
Page 383 of 1691
CRUIS E C O NTR O L S YSTE M
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Cruise Control Systems
Dakota, Durango, Ram Pickup, Ram Van & Ram Wagon
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
DESCRIPTION
The speed (cruise) control system is electronically
controlled and vacuum operated. The electronic control is integrated
into the Powertrain Control Module (PCM). System consists of the
following components: Powertrain Control Module (PCM), servo, speed
control switches, vacuum reservoir, vehicle speed sensor, speed
control relay and brake switch.
System controls are located on each side of steering wheel
air bag module and consist of ON/OFF, SET, RESUME/ACCEL, CANCEL AND
COAST buttons. System is designed to operate at speeds above 30 MPH.
OPERATION
SYSTEM CONTROLS
To Set Speed Control
Press ON/OFF button to turn speed control system on.
Accelerate to desired speed (minimum of 35 MPH) and press SET/COAST
button. Vehicle speed will be maintained.
NOTE: Speed control system will automatically disengage when
vehicle speed decreases to less than 35 MPH or increases to
more than 85 MPH.
To Disengage Speed Control
Press brake pedal. Press clutch pedal (M/T). Press CANCEL
button. Press ON/OFF button. If ON/OFF button is used, set speed will
be erased from memory.
To Resume Previous Speed
If set speed has not been erased from memory and vehicle
speed is more than 35 MPH, press RES/ACCEL button.
To Increase Speed
With speed control system on, increase set speed by rapidly
pressing and releasing RES/ACCEL button. Each pressing of button will
cause speed increase of 2 MPH. For example, pressing button 3 times
will increase speed by 6 MPH. To increase speed gradually, hold
RES/ACCEL button down until desired speed is reached. When button is
released, new set speed will be maintained.
To Decrease Speed
With speed control system on, decrease set speed by pressing
SET/COAST button. Vehicle speed will gradually decrease. Releasing
button will set a new speed as long as vehicle speed is still more
than 35 MPH.
Page 394 of 1691
voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next
Page 511 of 1691
ELE C TR IC AL C O M PO NEN T L O CATO R
1999 D odge P ic ku p R 1500
1999 ELECTRICAL COMPONENT LOCATION
Chrysler Motors Electrical Component Location
Dodge; Ram Pickup
SAFETY PRECAUTION
WARNING: When working on vehicles equipped with Supplemental Restraint
System (SRS), never apply electrical voltage to the system.
This could cause the SRS (air bag) to be deployed.
BUZZERS, RELAYS & TIMERS
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
A/C Compressor Clutch Relay On power distribution center.
Automatic Shut Down Relay On power distribution center.
Blower Motor Relay On power distribution center.
Central Timer Module Left side of dash, inboard of
steering column opening.
Combination Flasher Left side of dash, on
junction block.
Engine Starter Motor Relay On power distribution center.
Fog Lamp Relay On power distribution center.
Fuel Heater Relay (Diesel) On power distribution center.
Fuel Pump Relay On power distribution center.
Horn Relay On power distribution center.
Intake Air Heater Relay No. 1
(Diesel) On left inner fender, below
left battery.
Intake Air Heater Relay No. 2
(Diesel) On left inner fender, below
left battery.
Quad High Beam Relay On power distribution center.
Radio Choke Relay Behind center of dash, on
support.
Security Relay On power distribution center.
Trailer Tow Relay On power distribution center.
Transmission Control Relay On power distribution center.
Wiper Motor Relay On power distribution center.
\
\
\
\
\
\
\
Page 543 of 1691
IGNITION SWITCHES
INDICATOR LIGHTS
KEYLESS ENTRY KEYPADS AND TRANSMITTERS
KEYLESS ENTRY TRANSMITTERS
LEDS
LENSES
MICROPHONES
MIRRORS (ELECTROCHROMATIC AND HEATED)
MOTORS
NEUTRAL SAFETY SWITCHES
ODOMETERS
ODOMETERS, SPEEDOMETERS AND TACHOMETERS (CABLE-DRIVEN)
PULLEYS
RECEIVERS, AMPLIFIERS, EQUALIZERS AND SUB-WOOFER VOLUME CONTROLS
RELAY BOXES
RELAYS
SEALED BEAMS
SEAT HEATERS
SECURITY ALARM SENSORS
SIRENS
SOLENOIDS
SPEAKERS AND MICROPHONES
SPEEDOMETER AND TACHOMETER LINKAGES AND CABLES
SPEEDOMETER CABLES
SPEEDOMETERS
STARTERS
SUB-WOOFER VOLUME CONTROLS
SWITCHES
TACHOMETER CABLES
TACHOMETERS
TAPE PLAYERS AND CD PLAYERS
TENSIONERS
TIMERS
TIRE PRESSURE SENSORS
TRANSCEIVERS
TRANSDUCERS
VACUUM ACCUMULATORS (RESERVOIRS)
VACUUM RESERVOIRS
VOLTAGE REGULATORS
WASHER FLUID LEVEL SENDERS
WASHER PUMPS
WIPER ARMS AND BLADES
WIPER BLADES
WIPER HOSES AND NOZZLES
WIPER LINKAGES
WIPER NOZZLES
WIPER PUMP RESERVOIRS
WIRING HARNESSES AND CONNECTORS
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,