Boost DODGE RAM 1999 Service Repair Manual
Page 44 of 1691
BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument
Page 95 of 1691
knob pointer) is flush with base of A/C-heater control panel.
5) Rotate temperature control knob to its full clockwise
stop. Release knob. Knob pointer should be aimed at end of Red stripe.
If knob is pointed at end of Red stripe, go to next step. If knob is
not pointed at end of Red stripe, go back to step 2) and repeat
adjustment procedure.
6) Rotate temperature control knob to its full
counterclockwise stop. Release knob. If knob springs back, self-
adjuster clip securing temperature control cable to blend-air door
lever is improperly installed. See TEMPERATURE CONTROL CABLE R & I. If
knob does not spring back, temperature control cable adjustment is
complete.
TESTING
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
A/C-HEATER CONTROL PANEL TEST
1) Connect a vacuum gauge in line with Black A/C-heater
vacuum supply hose, located at tee near power brake booster (Dakota)
or in engine compartment (Durango and Ram Pickup). Position gauge so
it can be viewed from passenger compartment.
2) Start engine. While observing gauge, rotate mode control
knob to each mode position (one position at a time). Pause after each
selection. Test gauge should drop, then return to 8 in. Hg shortly
after each selection is made. If gauge reading is as specified, go to
next step. If gauge reading is not as specified, check for vacuum leak
in vacuum lines or A/C-heater control panel.
3) Move temperature control knob quickly to full hot and full
cold positions. A distinct sound of blend-air door hitting its stops
should be heard. No spring-back of knob should exist.
4) If temperature control knob operates as specified,
temperature control system is okay. On Dakota and Durango, if
temperature control knob does not operate as specified, check
condition, routing, installation, and adjustment of temperature
control cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT . Also check
blend air door for proper installation, obstructions, or faulty seals.
A/C SYSTEM PERFORMANCE
1) Park vehicle out of direct sunlight. Ensure ambient
temperature is at least 70F (21C). Connect tachometer and manifold
gauge set to vehicle. Turn A/C on. Turn mode control to panel and
recirculated air positions, temperature control lever to maximum
cooling, and blower to high.
2) Start engine and allow it to run at 1000 RPM, with A/C
compressor clutch engaged. Engine should be at operating temperature
with doors, windows, and hood closed. Insert thermometer into left
center air outlet.
3) Run engine and operate system for 5 minutes. The A/C
compressor clutch may cycle, depending on temperature. If A/C
compressor clutch cycles, stop engine and disconnect negative battery
cable. Remove clutch cycling pressure switch connector. Place a jumper
wire across terminals of clutch cycling pressure switch harness
connector.
4) Connect negative battery cable. Turn A/C on. Start and
Page 120 of 1691
BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument
Page 319 of 1691
* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS
Page 320 of 1691
SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
Page 337 of 1691
\
\
\
\
\
\
\
HYDRO-BOOSTERS
NOTE: Hydro-boosters and hydro-electric boosters are combined.
HYDRO-BOOSTER INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........ ( 1) Require replacement.
Connector missing ....... C ............ Require replacement.
Does not apply assist, or
inadequate assist ...... A .. Require repair or replacement.
Leaking ................. B .. Require repair or replacement.
Leaks fluid at fitting .. B ........... Require tightening or
replacement.
Leaks fluid at unit ..... B .. Require repair or replacement.
Leaks fluid from pressure
hose(s) ................ B . Require replacement of hose(s).
Leaks fluid into passenger
compartment ............ B .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Determine cause and correct prior to replacement of part.
\
\
\
\
\
\
\
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
See HYDRO-BOOSTERS .
IGNITION DISABLE SWITCHES
See SWITCHES.
Page 340 of 1691
missing ................ C .. Require replacement of missing
parts.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
(1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
PADS
See FRICTION MATERIAL .
PEDAL TRAVEL SWITCHES
See SWITCHES.
PEDALS
See BRAKE PEDALS.
POWERMASTER
See HYDRO-BOOSTERS .
PUMPS
See ELECTRICAL PUMPS AND MOTORS .
PRESSURE DIFFERENTIAL SWITCHES
See SWITCHES.
PRESSURE SWITCHES
See SWITCHES.
RELAYS
NOTE: Copied from Electrical UIGs
RELAY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Housing broken .......... A ............ Require replacement.
Housing cracked ......... 2 ............ Suggest replacement.
Inoperative ( 1) ......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned,
affecting performance .. A ........... ( 2) Require repair or
replacement.
Page 346 of 1691
\
\
\
\
\
\
\
Condition Code Procedure
Tire diameter incorrect,
affecting ABS or TCS ... A ............ Require replacement.
Tire pressure incorrect,
affecting ABS or TCS ... A .. Require repair or replacement.
Tire size incorrect,
affecting ABS or TCS ... A ............ Require replacement.
\
\
\
\
\
\
\
TOOTHED RINGS (TONE WHEEL)
NOTE: Copied from Drivetrain UIGs.
If the toothed ring requires replacement and cannot be
replaced as a separate component, replace the assembly of which the
ring is a part.
TOOTHED RING INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Alignment incorrect ..... B ............... Require repair or
replacement.
Bent .................... B ............ Require replacement.
Contaminated, affecting
performance ............. A ........ Require repair. Identify
and correct cause.
Cracked ................. B ............ Require replacement.
Loose ................... A ............. Require replacement
of worn parts.
Missing ................. C ............ Require replacement.
Number of teeth
incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
VACUUM BOOSTERS
VACUUM BOOSTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Applies too much assist
(oversensitive) ........ A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Auxiliary vacuum pump
inoperative ............ A ........... ( 1) Require repair or
replacement.
Check valve grommet
deteriorated, affecting
performance ............ A .. Require replacement of grommet.
Page 352 of 1691
BRAK E S YSTE M
1999 D odge P ic ku p R 1500
1998-99 BRAKES
CHRY - Disc & Drum - Trucks & Vans - Except FWD
Dakota, Ram Pickup, Ram Van
DESCRIPTION & OPERATION
All models are equipped with single-piston, sliding-caliper
front disc brakes with ventilated rotors. All models utilize self-
adjusting rear drum brakes. Rear Wheel Anti-Lock (RWAL) brake system
is standard on all models. Optional 4-wheel Anti-Lock (4WAL) brake
system is available on all models.
System also includes power brake booster, dual-reservoir
master cylinder and combination valve. Combination valve consists of
metering valve and pressure differential switch.
Models with diesel engine include a gear-driven vacuum pump.
Depending on speed of engine, pump produces 8-25 in. Hg. Models
without full-floating rear axle use 9", 10" or 11" single-anchor rear
brakes. Models with full-floating rear axle use 12" or 13" single-
anchor rear brakes.
NOTE: For information on Anti-Lock Brake Systems (ABS), see
appropriate ANTI-LOCK article.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
Complete Brake System
Before bleeding system, exhaust all vacuum from power unit by
depressing brake pedal several times. Bleed master cylinder using
bleeder screws (if equipped). Bleed wheel cylinders and calipers in
sequence. See BLEEDING SEQUENCE table.
BLEEDING SEQUENCE
\
\
\
\
\
\
\
Application Sequence
1999 Dakota & Ram Van .......... Master Cylinder, Combination Valve,
RR, LR, RF & LF
All Other Models ............... Master Cylinder, Combination Valve,
Rear Anti-Lock Valve, RR, LR, RF & LF
\
\
\
\
\
\
\
Master Cylinder (Bench Bleeding)
1) Bench bleed master cylinder before installation. Place
master cylinder in soft-jaw vise. Install bleeder tubes in both
outlets of master cylinder. See Fig. 1.
2) Fill master cylinder with clean brake fluid. Ensure ends
of bleeder tubes are submerged in brake fluid.
3) Using a wood dowel, apply and release master cylinder
until no air bubbles exist in brake fluid flow. Leave bleeder tubes
installed on master cylinder during installation. Install master
cylinder. Remove bleeder tubes, and connect brakelines. Bleed brake
system if necessary.
Page 354 of 1691
\
\
\
\
\
\
\
Application psi (kg/cm)
All Models ....................................... 10-15 (1.06-1.41)\
\
\
\
\
\
\
\
NOTE: When bleeding disc brakes, air may tend to cling to caliper
walls. Lightly tap caliper while bleeding to aid in removal
of air.
Manual Bleeding
1) Fill master cylinder. Install bleeder hose on first
bleeder valve to be serviced. See BLEEDING SEQUENCE table. Submerge
other end of hose in clean glass jar partially filled with clean brake
fluid.
NOTE: When bleeding brake system manually, ensure bleeder valve is
closed when brake pedal is released.
2) Open bleeder valve 3/4-1 turn. Depress brake pedal slowly
through full travel. Close bleeder valve. Release pedal. Repeat
procedure until fluid flow is free of air bubbles.
ADJUSTMENTS
PARKING BRAKE
1) Release parking brake, and loosen cable adjusting nut to
allow slack in cable. Adjust rear brakes. Tighten cable adjusting nut
until a slight drag is felt while rotating rear wheels.
2) Loosen cable adjusting nut until both rear wheels can be
rotated freely. Back off adjusting nut an additional 2 turns. Apply
and release parking brake several times, checking for free rotation at
rear wheels.
REAR BRAKE SHOES
1) Raise and support vehicle. Ensure parking brake lever is
fully released. Back off parking brake cable adjustment to ensure
cable has slack. Remove adjusting hole cover.
2) Using a brake adjuster, expand brake shoes until slight
drag is felt when wheel assembly is rotated. Using thin screwdriver,
hold automatic adjusting lever away from adjustment star wheel.
3) Back off adjustment star wheel until wheel assembly
rotates freely and brake shoe drag is eliminated. Repeat adjustment
for remaining wheels. Adjustment must be equal at all wheels. Replace
adjusting hole covers. Adjust parking brake. See PARKING BRAKE.
STOPLIGHT SWITCH
Stoplight switch is attached to brake pedal support. Push
stoplight switch through clip in mounting bracket until switch seats
in bracket. Pull brake pedal backward as far as pedal will travel.
Brake pedal will ratchet stoplight switch to correct position. Verify
full brake pedal return, and that stoplights glow when brake pedal is
applied.
TESTING
POWER BRAKE BOOSTER FUNCTIONAL TEST