Boost DODGE RAM 1999 Service Owner's Guide

SC HED ULE D S ER VIC ES
 Lubricant   GL-5 Gear Lube 





Power  All  Mopar Power Steering 

Steering   Fluid Or Equivalant 

Fluid (
3)   Petroleum Based 





Clutch  All  Multipurpose Grease 

Linkage   NLGI Grade 2 E.P. 

Lubricant   





A/C  All  R-134a 

Refrigerant   





A/C  All  Polyalkalene Glycol 

Refrigerant   SP10 PAG 

Oil   Refrigerant Oil 





(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 

(
3) - Never add gear oil, automatic transmission fluid or 

hydroboost power steering fluid. 



FLUID CAPACITIES
FLUID CAPACITIES TABLE



Item  Condition  Specification (1) 





Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 





 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 





 5.9L: Drained  4.5 Qts. (4.2L) 





Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 



(
2)  8.0L: Drained  24 Qts. (22.7L) 





Automatic  46RE: Dry Fill  1726 Pts. (812.3L) 

Transmission 



Fluid  47RE: Dry Fill  1733 Pts. (815.6L) 





Manual  NV3500  4.2 Pts. (2L) 

Transmission 



Fluid  NV4500  8 Pts. (3.8L) 





Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Lubricant 



 Model 248 (2WD)  6.3 Pts. (3L) 





 Model 248 (4WD)  7.3 Pts. (3.4L) 





 Model 267 (2WD)  7 Pts. (3.3L) 





 Model 267 (4WD)  7.8 Pts. (3.6L) 





 Model 286 (2WD)  6.8.Pts. (3.2L) 

REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
the COMPUTER RELEARN PROCEDURES article in GENERAL
INFORMATION before disconnecting battery.
POWER STEERING PUMP (GASOLINE)
WARNING: DO NOT attempt to remove power steering pump without removing
power steering pump belt. Personal injury or pulley damage
could result.
Removal
1) Disconnect and isolate negative battery cable. To remove
serpentine belt, rotate tensioner clockwise and hold in place, slide
belt from tensioner pulley. Place drain pan under pump. Disconnect and
cap hoses.
2) Remove bracket-to-engine block bolts. Remove pump, pulley
and mounting bracket as an assembly. To allow access to pump screws,
remove pump pulley. See PUMP PULLEY. Remove bracket-to-pump screws.
Installation
To install pump, reverse removal procedure. Fill and bleed
system. See HYDRAULIC SYSTEM BLEEDING under LUBRICATION.
VACUUM/POWER STEERING PUMP (DIESEL)
Removal
1) Disconnect negative battery cable. Place drip pan under
vacuum/power steering pump. Disconnect and cap power brake booster
hose at vacuum pump and hydraulic lines at power steering pump.
Disconnect oil pressure sending unit electrical connector. Remove
sending unit from engine block and plug hole in block. Disconnect and
cap oil feed line from bottom of vacuum pump.
2) Remove vacuum/power steering pump-to-engine block nuts and
bolts, and mounting bracket. Remove upper pump bolt and remove pump.
Drain fluid from steering pump reservoir. Remove gaskets from mounting
surfaces.
CAUTION: DO NOT damage internal vacuum pump oil seal when separating
steering pump from vacuum pump. See Fig. 5.
3) Remove steering pump-to-vacuum pump bracket bolts.
Carefully slide steering pump from bracket. Remove 2 pump body
spacers. See Fig. 5.
NOTE: Steering pump housing and spacers must mate completely with
vacuum pump bracket.
Installation
1) Install 2 pump body spacers and rotate drive gear until
steering pump and vacuum pump drive splines align. See Fig. 5.
Carefully install steering pump on vacuum pump bracket to prevent
damaging oil seal.


I - S YSTE M /C O M PO NEN T T E STS

1999 D odge P ic ku p R 1500
1999 ENGINE PERFORMANCE
CHRY - System & Component Testing - Trucks - Diesel
Ram Pickup
INTRODUCTION
Before testing separate components or systems, perform
procedures in BASIC DIAGNOSTIC PROCEDURES - TRUCKS - DIESEL article.
Since many computer-controlled and monitored components set a
diagnostic trouble code if they malfunction, also perform procedures
in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
NOTE: Testing individual components does not isolate short or open
circuits. Perform all voltage tests with a Digital Volt
-Ohmmeter (DVOM) with a minimum 10-megohm input impedance,
unless stated otherwise in test procedure. Use ohmmeter to
isolate shorted or open wiring harness.
AIR INDUCTION SYSTEMS
INTAKE MANIFOLD AIR HEATER SYSTEM
For testing information on intake manifold air heater system,
perform procedures in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article.
INTERCOOLER
Cleaning and inspection procedures for intercooler is the
only information available from manufacturer. See INTERCOOLER under
AIR INDUCTION SYSTEMS in REMOVAL, OVERHAUL & INSTALLATION - TRUCKS -
DIESEL article.
TURBOCHARGER
NOTE: Manufacturer does not recommend turbocharger disassembly.
Turbocharger overhaul should be performed only by an
authorized repair facility.
Turbocharger Boost Pressure
Turbocharger boost pressure testing information is not
available at time of publication.
TURBOCHARGER WASTEGATE
See CONTROL ROD ADJUSTMENT under TURBOCHARGER WASTEGATE in
ON-VEHICLE ADJUSTMENTS - TRUCKS - DIESEL article.
COMPUTERIZED ENGINE CONTROLS
POWERTRAIN CONTROL MODULE (PCM)
The PCM is located on firewall at passenger's side rear
corner of engine compartment. See Fig. 1. The PCM power and ground
circuits may be checked by performing specified test. See DTC P0601 in
SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.

NOTE: Turbocharger is not serviceable and must be replaced as a
complete assembly. Turbocharger overhaul procedures should
only be performed by an authorized facility.
Turbocharger is mounted on exhaust manifold. See Fig. 1.
Exhaust gases rotate turbine wheel along with the shaft and compressor
wheel. Rotating of compressor wheel forces an increased amount of
airflow (boost pressure) through intercooler and then into intake
manifold where the air is distributed into each cylinder. Supplying
increased airflow provides improved engine performance, lower exhaust
smoke density, altitude compensation and reduced engine noise.
Turbocharger contains a wastegate which is used for controlling boost
pressure at high speeds. Turbocharger is lubricated by pressurized
engine oil from engine oiling system. Excess engine oil is returned
through turbocharger oil return line into the cylinder block.
Fig. 2: Locating Fuel System & Various Engine Components
Courtesy of Chrysler Corp.
COMPUTERIZED ENGINE CONTROLS

thermostat housing. See Fig. 2.
Fuel Injection Pump Control Module (FPCM)
Fuel Pump Control Module (FPCM) controls fuel pump using
inputs from Engine Control Module (ECM). FPCM is integral to top of
fuel pump. ECM and FPCM are interconnected together for fuel injection
control.
Fuel Temperature Sensors
There are 2 fuel temperature sensors. One sensor is located
inside injection pump, and will set FTC under high temperature
conditions. Engine Control Module (ECM) will lower engine power if FTC\
is set. Other sensor is an integral part of fuel heater. See FUEL
HEATER.
Intake Manifold Air Temperature (IAT) Sensor
Intake manifold air temperature sensor is a variable
thermistor sensor located on top of intake manifold, behind intake
manifold air heater. See Fig. 4. Intake manifold air temperature
sensor delivers an input signal to Engine Control Module (ECM) to
indicate intake manifold air temperature. ECM uses input signal for
controlling intake manifold air heater, fuel control and timing.
Fig. 4: Locating Intake Manifold Air Temperature Sensor & MAP Sensor
Courtesy of Chrysler Corp.
Manifold Air Pressure (MAP) Sensor (Boost Pressure)
Manifold Air Pressure (MAP) sensor, located at rear of intake\

manifold, sends input signal to Engine Control Module (ECM). ECM uses
input signal for controlling fuel control, timing and engine
protection. ECM will lower engine power if boost is too high.
Oil Pressure Sensor
Oil pressure sensor signal is input to Engine Control Module
(ECM). ECM converts signal to pressure value. Value is sent on CCD Bus\
to instrument panel gauge/light. Oil pressure sensor is located on
side of engine block, below ECM. See Fig. 2.
Power Take Off (PTO)
This input is used on vehicles equipped with a Power Take Off
(PTO) unit. When PTO is engaged, Engine Control Module (ECM) will
disable some OBD-II functions.
Water-In-Fuel (WIF) Sensor
WIF sensor is located in bottom of fuel filter/water
separator. See Fig. 2. WIF sensor delivers input signal to Engine
Control Module (ECM) when water exists in the fuel filter/water
separator. As water level increases, resistance across WIF sensor
decreases. ECM compares decrease in resistance to a high water
standard value. When resistance is 30,000-40,000 ohms, ECM will turn
on WATER-IN-FUEL warning light. WATER-IN-FUEL warning light is located
on instrument panel, just below tachometer. ECM monitors input signal
when ignition switch is in the ON position and continues to monitor
input signal until intake manifold air heater post-heat cycle is
complete.
PCM INPUT SIGNALS
A/C Switch
When A/C switch is in ON position, an input signal is
delivered from A/C switch to Engine Control Module (ECM) to indicate
that A/C operation has been requested. Once A/C operation has been
requested, an A/C request signal is delivered to ECM from A/C high-
pressure switch and A/C low-pressure switch. The A/C request signal
indicates evaporator pressure is within proper range for A/C
operation. ECM uses A/C request signal to cycle A/C compressor clutch
by using an A/C clutch relay. A/C clutch relay may also be referred to
as A/C compressor clutch relay. If A/C high-pressure switch or A/C
low-pressure switch opens, A/C request signal will not be delivered to
the ECM. ECM will then open ground circuit for A/C clutch relay and
A/C compressor clutch will be disengaged.
The A/C clutch relay is located in power distribution center
at driver's side front corner of engine compartment, near the battery.
The A/C high-pressure switch is located on discharge line, near A/C
compressor. The A/C low-pressure switch is located on top of
accumulator.
Accelerator Pedal Position Sensor (APPS) Output From ECM
Accelerator Pedal Position Sensor (APPS) is mounted on top
left of engine. See Fig. 2. Sensor provides DC voltage input signal to
Engine Control Module (ECM) to indicate throttle position. On previous\
engines, there were linkages between accelerator pedal, throttle
position sensor and injection pump. On this engine, no linkage exists
between accelerator pedal and injection pump. APPS signal is sent on
CCD Bus circuit from ECM to PCM.
Automatic Shutdown (ASD) Relay
A 12-volt input signal is delivered from ASD relay to Engine
Control Module (ECM) when ASD relay is energized. If ECM does not
receive a 12-volt input signal when ASD relay is energized, a
Diagnostic Trouble Code (FTC) will be stored in ECM. ASD relay is

Dakota & Durango
1) Raise and support vehicle. Ensure shift lever is in Park.
Release shift cable adjuster lock. Shift cable adjuster lock is
located on shift cable, just below brake booster.
2) Disconnect shift cable from transmission shift lever on
transmission. Ensure transmission is still in Park by rotating
transmission shift lever fully toward rear of vehicle to Park detent.
3) Verify parking sprag on transmission is engaged by
attempting to rotate drive shaft. Install shift cable on transmission
shift lever. Lock shift cable in place by pressing shift cable
adjuster lock downward until it snaps into place.
4) To verify proper adjustment, check that engine only starts
with shift lever in Park and Neutral. If engine starts in any other
gears except Park or Neutral, shift cable may be improperly adjusted
or park/neutral position switch may be defective.
Ram Van/Wagon
1) Raise and support vehicle. Ensure shift lever is in Park.
Unsnap shift cable from ball at transmission shift lever on
transmission. See Fig. 6.
2) Check that transmission is still in Park by rotating
transmission shift lever fully toward rear of vehicle to Park detent
position. Release cable adjuster at transmission end of shift cable to
unlock shift cable. See Fig. 6. Snap shift cable back on ball at
transmission shift lever. Press cable lock inward to secure shift
cable.
3) To verify proper adjustment, ensure engine only starts
with shift lever in Park and Neutral. Shift lever should not move from
Park when ignition switch is in LOCK position. Shift lever should move
from Park when ignition switch is in any position except LOCK
position.
Fig. 6: Locating Cable Adjuster (Ram Van/Wagon)
Courtesy of Chrysler Corp.
SHIFT LINKAGE