AUX DODGE SPRINTER 2005 1.G User Guide

136 UNDERSTANDING YOUR INSTRUMENT PANELHeat operation:
Different operating conditions will be in effect
depending on the heat level required.
The integrated control unit adjusts the heat flow using
the following operating levels:
High – Low – Off
Safety Equipment
For safety reasons, the heater will automatically switch
off if faults occur which cause the device to overheat.
Tips for Coping with Problems; refer to "Auxiliary
Heater – Tips for Coping with Problems".
The integrated control unit contains a diagnostic
system which detects and stores faults. The error can
be read by means of the vehicle diagnosis. If a fault
occurs while the heater is switched on, the
symbol ö will flash and the error code for that fault
will be displayed in the timer.
The fault should be corrected as soon as possible by an
authorized Sprinter Dealer.
Settings with the Auxiliary Heater switched onIn preheat mode, the blower is automatically switched
on at blower speed 1 when the water heater is switched
on. When driving, the airflow control switch (2) can be
set as desired.

UNDERSTANDING YOUR INSTRUMENT PANEL 137
4
NOTE: Only on vehicles with automatic heater
control/regulated air conditioner:
Before switching on the heater or entering the switch-
on time, the temperature control (1) must be set to
maximum heater output (as illustrated).
Set the air distribution control (3) as required between
Y and Z .AUXILIARY HEAT EXCHANGER IN LOAD
COMPARTMENT, ONLY WITH AUXILIARY HEATER
(OPTIONAL)
The auxiliary heat exchanger switch
is located on the right next to the
steering column. To switch on at blower speed 1:
Press the upper section, the left-hand indicator lamp in
the switch lights up.
To switch on at blower speed 2:
Press the lower section, the right-hand indicator lamp
in the switch lights up.
To switch off :
Press the switch to the middle position.
Operation is only possible when the key is turned to
position 2 in the ignition lock.
NOTE:
The auxiliary heat exchanger in the load
compartment should be switched off at coolant
temperatures below 176 °F (+80 °C) to quickly de-fog
and de-ice the windshield and front side windows.

138 UNDERSTANDING YOUR INSTRUMENT PANELAUXILIARY HEATER – TIPS FOR COPING WITH
PROBLEMSNOTE: After three successive attempts to start the
heater, a malfunction will be recorded in the integrated
diagnostic system and no further operation on
auxiliary heater will be available (lock-out). The work
to annul the lock-out must be carried out at an
authorized Sprinter Dealer.
The heater either does not switch on or automatically
switches off:
 Insufficient fuel, fill up the fuel tank. Start up heater two times, until the fuel lines are filled.
 The auxiliary heater will automatically switch off if the fuel level is under about 4 US gal (15 l).
 The fuses in the fuse box are damaged. Electric fuses.
 The battery voltage is too low, an undervoltage protector switches off the heater if the battery
voltage falls below about 10 volts. The heater motor does not run
 The battery voltage is too low, check the battery.
Batteries.
 The fuses in the fuse box are damaged. Electric fuses.
 The heater motor is damaged.
Overheating The air channels are clogged. The heater can be restarted once the fault has been
repaired. When this is done, the heater should be
switched on and off.
 The heater will remain switched off after it has been overheated a number of times (about 10 times in
succession). Have the fault repaired by an
authorized Sprinter Dealer.
NOTE: Repairs should only be made by an authorized
Sprinter Dealer.

140 STARTING AND OPERATING

Deactivating the Acceleration Skid
Control (ASR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Brake Assist System (BAS)
(vehicle type 2500 only) . . . . . . . . . . . . . . . . . . . 169
Indicator Lamp Electronic Stability Program
(ESP) (type 2500 vehicles only) . . . . . . . . . . . . 170
Electronic Stability Program (ESP)
(vehicle type 2500 only) . . . . . . . . . . . . . . . . . . . 171


Auxiliary Drive (Optional) . . . . . . . . . . . . . . . . . . 172


Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173


Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Tire Grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Hydroplaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 175


Tire Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Tire Pressures of Loaded Vehicle in PSI (kPa) . . . 177
Vehicle type 2500 C/HC/SHC . . . . . . . . . . . . 177
Vehicle type 3500 C/HC/SHC . . . . . . . . . . . . 177
Comfort Tire Pressures in PSI (kPa) . . . . . . . . 178
Comfort Tire Pressures in PSI (kPa) . . . . . . . . 178


Snow Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179


Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 179
Fuel Filter with Water Separator . . . . . . . . . . . 180
Diesel Fuels for Use at Very Low
Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . 180


Refueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182


Programmed Top Speed (Optional) . . . . . . . . . . 182


Bleeding Diesel Fuel System . . . . . . . . . . . . . . . . . 183


Draining Fuel Filter with Water Separator . . . . . 184
Bleeding the Diesel Fuel Syst em . . . . . . . . . . . 185


Permissible Roof Load . . . . . . . . . . . . . . . . . . . . . . 186


Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Trailer Hitches (Optional) . . . . . . . . . . . . . . . . . 186
Electrical Connections (Optional) . . . . . . . . . . 186
Vehicle and Trailer Weights and Ratings . . . . 187
Loading a Trailer . . . . . . . . . . . . . . . . . . . . . . . . 187
Checking Weights of Vehicle and Trailer . . . . 188
Attaching a Trailer . . . . . . . . . . . . . . . . . . . . . . . 188
Towing a Trailer . . . . . . . . . . . . . . . . . . . . . . . . . 189
Parking a Trailer . . . . . . . . . . . . . . . . . . . . . . . . . 191


Emissions Control System (Catalytic Converter) 192


Inhalation of Exhaust Gas . . . . . . . . . . . . . . . . . . . 192


Fording (Wading Capability) . . . . . . . . . . . . . . . . 192


Body Builder Guideline . . . . . . . . . . . . . . . . . . . . . 193
A Special Note Concerning Vehicle
Alteration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

172 STARTING AND OPERATING
AUXILIARY DRIVE (OPTIONAL)1. Auxiliary drive
2. Ribbed V-belt (not part of factory package)
3. Tensioner pulley
4. Support
5. Unit (not part of factory package)
NOTE: When retrofitting a unit pay attention to the
running direction of the engine.
WARNING!
ESP cannot prevent the natural laws of physics
from acting on the vehicle, nor can it increase the
traction afforded.
The ESP cannot prevent accidents, including
those resulting from excessive speed in turns,
following another vehicle too closely, or
hydroplaning. Only a safe, attentive, and skillful
driver can prevent accidents.
The capabilities of an ESP equipped vehicle must
never be exploited in a reckless or dangerous
manner which could jeopardize the user’s safety
or the safety of others.If the vehicle is to be towed away with the front
wheels clear of the ground, or if the brakes are to be
tested on a brake dynamometer, do not put the key
in position 2 in the ignition lock because the ESP
would engage the brakes to stabilize the vehicle.If the ESP function is used for a prolonged period
of time, the rear axle brakes may fail due to
overheating.

STARTING AND OPERATING 173
5
STEERINGWhen the engine is not running, there is no power
assistance for the steering. Greater force will be
required to steer the vehicle.WHEELS AND TIRESCheck tires regularly for even tread wear, tread depth
(note legal requirements) and signs of external
damage.
Only use wheels and tires of the same size, make and
pattern.
Do not install tires that are not approved for the size
and type of wheel installed or the vehicle itself. Only
use those wheel sizes which were delivered to you by
your authorized Sprinter Dealer.
Use only wheels and tires which have been tested and
approved by the vehicle manufacturer. Break in new tires at moderate speeds for a distance of
about 65 miles (about 100 km).
CAUTION!
Power take off must not exceed 10 kW. Exceeding
the power take off may cause damage to the
auxiliary drive and/or ribbed V-belt.
WARNING!
Fitting other wheel sizes to the vehicle will change
the vehicle’s handling characteristics and may
lead to an accident resulting in severe personal in-
juries, death and property damage.
Only certain tires meeting the tire size/load/speed
rating specifications contained in the Tire
Pressure Tables at the end of this chapter are
certified to conform to FMVSS 120 for the Sprinter
vehicle at this time. Please check your side walls
of your originally equipped tires for specific
makes/sizes, and speed load ratings when you
need to replace your tires.
To prevent accident, injury or possible death, use
only the correct tires for your tire replacement.
Do not use retreaded/ remolded tires. This process
does not always permit previous damage to be
detected. Therefore vehicle safety cannot be
guaranteed if retreaded/remolded tires are fitted
.

182 STARTING AND OPERATINGNOTE: Only fill the fuel tank until the fill nozzle cuts
off, do not overfill.
NOTE: Holder on the inside of the fuel filler flap only
for cargo/passenger vans.
CapacityFuel tank including reserve fuel about 26.4 US gal
(100 l).PROGRAMMED TOP SPEED (OPTIONAL)NOTE: The top speed of this vehicle can be
electronically limited to a speed between 19 mph
(30 km / h) and 82 mph (132 km / h). The vehicle’s
electronic speed controller should be programmed
only by a qualified technician by an authorized
Sprinter Dealer.
When programming the electronic speed controller,
the circumference of the specific tires actually mounted
on the vehicle must be determined and that
circumference must be correctly programmed into the
vehicle’s electronic speed controller. It is critical that
the correct tire circumference be programmed
accurately into the vehicle’s electronic speed
controller. Accurate tire circumference information
should be confirmed each time the electronic speed
controller is programmed and each time new wheels or
tires are mounted on the vehicle.
WARNING!
Always handle fuel with great care.
Shut off the engine and the auxiliary heater before
refueling.
Fuel is flammable and explosive. Keep open
flames away from the fuel.
Refrain from smoking as well as use of any
electrical equipment (such as cell phones). This
also applies to places where the characteristic
smell of fuel is evident.
If diesel fumes are noticed inside the vehicle, have
the cause traced and rectified immediately by an
authorized Sprinter Dealer.

216 MAINTAINING YOUR VEHICLELegend For Engine Compartment
1. Windshield washer system fluid reservoir.
2. Maintenance indicator for air cleaner element (Optional).
3. Oil dipstick.
4. Oil filler neck.
5. Ribbed V-belt. Auxiliary drive (Optional) refer to “Auxiliary
drive“. 6. Fuel filter with water separator.
7. Hydraulic brake fluid reservoir.
8. Coolant reservoir.
9. Battery
The auxiliary battery is located underneath the
front passenger seat (optional equipment).
10. Fuse box (These special fuses should only be replaced at by
an authorized Sprinter Dealer).

MAINTAINING YOUR VEHICLE 227
7
BATTERIESThe standard battery is located in the engine
compartment. The auxiliary battery is lo
cated underneath the front
passenger seat (optional equipment).
The battery will not achieve its maximum service life
unless it is kept adequately charged at all times. If the
vehicle is used primarily for short distances, or left
parked for lengthy periods, have the battery charge
checked more frequently.
Disconnecting the Battery
WARNING!
Failure to follow these instructions can result in
severe personal injuries and death.
Never lean over batteries while connecting, you
might get injured, if the battery explodes.
Battery fluid contains sulfuric acid. Do not allow
this fluid to come in contact with eyes, skin or
clothing. In case it does, immediately flush
affected area with water and seek medical help if
necessary.
A battery will also produce hydrogen gas, which
is flammable and explosive. Keep flames or
sparks away from battery, avoid improper
connection of jumper cables, smoking etc.
Use only impact-resistant batteries with a central
gas release cover to prevent corrosion damage and
to prevent occupants from caustic burns in the
event of an accident.
CAUTION!
Do not loosen or remove the battery terminal
clamps while the engine is running or the key is in
the ignition lock as this could damage electrical or
electronic equipment beyond repair. All electrical
consumers must be switched off.
Do not place any metal objects on the battery.
Doing so may cause a short-circuit.
Loosen and remove the negative terminal clamp
first, then the positive terminal.
Afterwards disconnect vent tube from the fitting.

278 INDEXASSYST Maintenance Computer . . . . . . . . . . . . . . . 110
Automatic Lock Feature . . . . . . . . . . . . . . . . . . . . . . . . 19
Automatic Transmission . . . . . . . . . . . . . . . . . . . . . . 145Accelerator Position . . . . . . . . . . . . . . . . . . . . . . . . 146
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Gear Selector Lever Position . . . . . . . . . . . . . . . . . 147
Maneuvering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Selector Lever Manually Unlocking. . . . . . . . . . . 150
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Auxiliary Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Auxiliary Heat Exchanger . . . . . . . . . . . . . . . . . . . . . 137
Auxiliary Heater Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Timer Auxiliary Heater (Water and Air Heater) 132
Tips for Coping with Problems . . . . . . . . . . . . . . 138BBatteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . 228
Disconnecting the Battery . . . . . . . . . . . . . . . . . . . 227
Reconnecting the Battery . . . . . . . . . . . . . . . . . . . . 228
Replacing Batteries in Remote Keyless Entry . . . . 22
Battery Charge Indicator Lamp . . . . . . . . . . . . . . . . . 104 Belt Tensioners
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Belt Tensioners and Airbag . . . . . . . . . . . . . . . . . . . . . 49
Bleeding the Diesel Fuel System . . . . . . . . . . . . . . . . 185
Body Builder Guideline . . . . . . . . . . . . . . . . . . . . . . . 193
Brake Assist System (BAS) . . . . . . . . . . . . . . . . . . . . . 169
Brake fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Brake Fluid Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . 222
Brake Indicator Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 157
Brake Pad Wear Indicator. . . . . . . . . . . . . . . . . . . . . . 156
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Brake System, Anti-Lock . . . . . . . . . . . . . . . . . . . . . . 162
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Service Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bulbs Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Front Lamp Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
CCapacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Care of Vehicle