key FIAT DOBLO 2009 2.G Blue And Me Manual

36
The SETTINGSmenu gives you the fol-
lowing choices:
❒Register a mobile phone
❒Manage user data
❒Advanced options.
To operate within the Settingsmenu
when the car is stationary, you can use
either the steering wheel controls or voi-
ce commands. When the car is moving,
you can use only voice commands. In-
structions for both methods follow.

IF YOU HAVE SOME DIFFICULTIES
USING THE BLUE&ME™ settings func-
tions, see the TROUBLESHOOTING
section.REGISTERING A MOBILE PHONE
In order to use your mobile phone with
the vehicle's hands-free function, it must
be registered.
During the registration process, the
hands-free system searches for a phone
with Bluetooth
®technology in its re-
ception range. If it finds one, it establish-
es a connection with it by using a Person-
al Identification Number (PIN). After you
have registered your mobile phone on the
system, you can use it with the hands-free
system.
IMPORTANT The PIN code used for reg-
istering a mobile phone is produced ran-
domly by the system each time a new
phone is registered, therefore you do not
need to remember it. If you lose it, you
can still use the hands-free system.
You only need to register your phone
once; after that, Blue&Me™will auto-
matically connect to it every time you get
in the vehicle and turn the ignition key to
MAR.You can register your mobile phone by
choosing REGISTRATIONin the SET-
TINGSmenu.
?
To perform the registration manu-
ally, proceed as follows:
Activate the Main Menu by pressing
ß/MENUand select SETTINGS
by pressing SRC/OKor
ß/MENU.
Select REGISTRATIONand then
press SRC/OKor
ß/MENU. The
system begins the registration
process.
The system displays the PIN code
necessary for registering the mobile
phone on the instrument panel and
repeats it out loud. It is important
to know that this PIN is only used
for registering the mobile phone; it
is not your SIM card PIN.
For the next two stages, consult your
mobile phone manual on how to reg-
ister and connect with Bluetooth
®
devices.
SETTINGS
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:55 Pagina 36

37
On your mobile phone, look for the
option that finds in-range Blue-
tooth
®devices (it may be called
Find, Add Device, etc.). From the list
of available Bluetooth
®devices,
choose “Blue&Me” (the name that
identifies the Blue&Me™system
on your vehicle).
When prompted by your phone, en-
ter the PIN number shown on the
instrument panel display. If the reg-
istration was successful, the system
will say “Connection in progress”
and you get confirmation at the end
when the display shows details of the
mobile phone registered.
It is important to wait for this con-
firmation message – if you press
ß/MENUor &/ESCbefore it ap-
pears, you risk cancelling the regis-
tration process. If registration fails,
an error message will appear; in this
case, you will need to start again.The first time a mobile phone is reg-
istered, the system says “Wel-
come” as soon as it is connected.
This welcome message will not be
delivered during subsequent regis-
trations or connections of the same
mobile phone.
The system will ask you if you want
to copy across the contacts of the
phone you have just registered.
Copying the phonebook is recom-
mended.
To copy the contacts, press SRC/
OKor
ß/MENU. If you do not
want to copy the phonebook, press
&/ESC. If you do not copy the
phonebook at this point, you can
copy it later by choosing SET-
TINGS, USER DATA, CON-
TACTS.
On some mobile phones, the names
in the phonebook are not copied
automatically, but have to be trans-
ferred by using the mobile phone
keypad. If prompted by the system,
carry out this procedure following
the specific instructions for your
mobile phone and press
ß/MENU
when you have finished.
}
Or, with voice interaction:
Press
‘and say “Settings” and
then, at the end of the message from
the system, say “Register user”.
The system displays the PIN code
for registration on the instrument
panel and repeats it out loud.
For the next two stages, consult
your mobile phone manual on how
to register and connect with Blue-
tooth
®devices.
On your mobile phone, look for the
option that finds in-range Blue-
tooth
®devices (it may be called
Find, Add Device, etc.). From the list
of available Bluetooth
®devices,
choose “Blue&Me” (name that
identifies your vehicle's hands-free
system).
When prompted by your mobile
phone, enter the PIN code shown
on the display with your mobile
phone keypad. If the registration
was successful, the system will say
“Connection in progress” and
you get confirmation at the end
when the display shows details of
the mobile phone registered.
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:55 Pagina 37

38
It is important to wait for this con-
firmation message – if you press
ß/MENUor &/ESCbefore it ap-
pears, you risk cancelling the regis-
tration process. If registration fails,
an error message will appear; in this
case, you will need to start again.
The first time a mobile phone is reg-
istered, the system says “Welcome”
as soon as it is connected. This wel-
come message will not be delivered
during subsequent registrations or
connections of the same mobile
phone.
The system will ask you if you want
to copy the phonebook from the
phone you have just registered.
Copying the phonebook onto the
system is recommended. To copy
the phonebook, say “Yes”. If you do
not want to copy the phonebook,
say “No”.
On some mobile phones, the names
in the phonebook are not copied au-
tomatically, but have to be trans-
ferred by using the mobile phone
keypad. If prompted by the hands-
free system, carry out this procedure
following the specific instructions for
your mobile phone and press
ß/MENUwhen you have finished.Suggestions
To improve the voice recognition of the
names in your phonebook and the pro-
nunciation accuracy of Blue&Me™, try
to enter and save your contacts as follows:
❒Avoid abbreviations.
❒Write foreign names the way they are
pronounced according to the rules of
the Blue&Me™language set on your
vehicle. For example, it is advisable to
enter “Thorsten” as “Torsten” to im-
prove recognition and get the system to
pronounce the names correctly.
❒When you add or amend names in the
phonebook, enter the appropriate signs
for any accents so that they are pro-
nounced correctly and recognised by the
system. For example, it is advisable to
enter “Nicolo Rebora” as “Nicolò Réb-
ora” to get the correct pronunciation.
❒When you add or amend names in the
phonebook, remember that some isolat-
ed upper-case letters can be read as ro-
man numerals (e.g. V can be read as five).
❒When you call people using voice
recognition, do not use shortened ver-
sions of the name or middle initials. N.B.
❒You only need to register your phone
once.
❒You can register up to five mobile
phones on the system, which can be
used one at a time.
❒To connect a mobile phone to
Blue&Me™that has already been reg-
istered, you always need to switch on
the phone's Bluetooth
®setting.
❒Before you transfer the contacts from
your mobile phone to the hands-free
system, make sure the name of each
person is unique and clearly recognis-
able so that the voice recognition sys-
tem works properly.
❒The system will copy only valid con-
tacts, i.e. those containing a name and
at least one phone number.
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:55 Pagina 38

58
Problem Probable cause Possible solution
The display shows:
NO PHONE
Or the system says
“No phone connected”
The display shows:
PHONE DISCONNECTED
The display shows:
REGISTRATION FAILED
Or the system says
“Registration unsuccessful.
Please try again”
❒Turn the mobile phone on
❒Make sure that your phone has
been registered
❒Make sure that the Bluetooth®
connection between your mobile
phone and the vehicle's hands-free
system has been activated
(“Blue&Me” identification)
❒Make sure that the mobile
phone that you registered on the
vehicle's hands-free system is within
the system's operating range
❒Turn the mobile phone off and on
again to restore the connection
with Blue&Me™
❒Restart Blue&Me™by turning the
ignition key to STOPand then back
to MAR
❒Check that the PIN number is correct
and try to enter it again
❒Turn the mobile phone off and on again
and then repeat the registration process

SETTINGS – MOBILE PHONE
REGISTRATION
❒The mobile registered is switched off
❒The mobile registered is not within
the system's operating range
(it should be within about
10 m from the system)
❒The Bluetooth®connection
between the system and the mobile
has been disabled on your mobile
phone (“Blue&Me” identification)
❒An error has been detected in
your mobile phone's Bluetooth®
connection
❒During a phone conversation,
the mobile phone left the hands-free
system's operating range
❒An error was detected during the
registration procedure
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:56 Pagina 58

62
Problem Probable cause Possible solution
If you try and register a phone that
has already been registered, the display
shows: Registration unsuccessful
or, the system says “Registration
unsuccessful. Please try again”
After having copied the mobile's
phonebook to the hands-free system,
the titles, qualifications or middle initials
(Mr, Dr, BA, QC, etc.) in the name
have not been recognised by the voice
recognition system
You need to register your phone only once;
after that, Blue&Me™will automatically
connect to it every time you get in the
vehicle and turn the ignition key to MAR.
If you need to repeat the registration of
a mobile phone that has already been
registered, select DELETE USERSon
the system and then repeat registration

SETTINGS – MANAGING DATA
AND CONTACTS

SETTINGS – MOBILE PHONE
REGISTRATION
When you call a contact in your
mobile's phonebook using voice
recognition, say the name without using
titles, qualifications or middle initials
If you have two contacts with similar
names and/or surnames in your mobile
phonebook, change one of the names to
make it unique and copy the phonebook
onto the hands-free system again Before repeating the registration
of a mobile phone that has already
been registered, you need to delete
the information relating to the previous
registrations on Blue&Me™
When you call a contact in your
mobile phonebook using voice
commands, the voice recognition
system does not support the use
of titles, qualifications or middle initials
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:56 Pagina 62

66
MEDIA PLAYER
Problem Probable cause Possible solution
Display shows: NO FILE
or, Blue&Me™says:
“No multimedia file found”
After having inserted a USB device and
turned the ignition key to MAR,
no music is heard
After having inserted a USB device
and turned the ignition key
to MAR, there are malfunctions
in Blue&Me™ (e.g. failure to play
music tracks or no voice messages)
❒Follow the instructions to connect
your UBS device to Blue&Me™.
❒Put the digital audio files on your
USB storage device following the
instructions in your multimedia file
management software.
❒Remove the USB device from the
vehicle's USB port and reinsert it.
When it is inserted again, the
multimedia library will be recreated.
❒To be compatible with Blue&Me™,
a USB device must be classified as
a USB mass storage device.
Wait for the library to be created.
If the creation of the library takes too
long, you can decide to reduce the
number of digital audio files on your
USB device.
Disable this function on the USB
device.
❒No USB device is connected to the
vehicle's USB port.
❒No digital audio file is present on the
USB storage device.
❒If there is a break in the power
supply, for example if the car
battery is disconnected, Blue&Me™
loses power temporarily and the
multimedia library must be recreated
❒Your USB storage device is not
supported by Blue&Me™.
Creating the multimedia library may
take several minutes.
You may have used a USB device with
its PASSWORD function on.
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:56 Pagina 66

67
Problem Probable cause Possible solution
Display shows:NO PLAYLIST
or, Blue&Me™says:
“No playlist found”
Display shows:
PLAYLIST ERROR
Display shows:
PLAYLIST EMPTY
or, Blue&Me™says:
“Playlist empty”
Display shows:FILE ERROR
Sound system display shows:
MEDIAPLAYERwithout
USB device connected to
the USB port on the vehicle
Create a playlist on your computerusing
your multimedia file management software,
and add it to your USB device
❒Make sure the playlist is in
.m3uor .wplformat.
❒Create the playlist again following the
instructions in the
CREATING A PLAYLIST FOR Blue&Me™
section of SUGGESTIONS.
❒If the problem persists, delete the playlist
from your USB device.
❒Delete the playlist from your USB device
or insert the multimedia files in the playlist,
using your multimedia file management
software.
❒Reduce the number of songs in the playlist,
using your multimedia file management
software.
If the digital audio is damaged, delete it from
your USB device
❒Press the SRC/OKbutton or the appropriate
buttons on the front of thesound system to
change the audio source.
❒With the ignition key turned to MAR, insert
and then remove the USB device from the
vehicle's USB port.
❒To avoid the MEDIAPLAYERwithout USB
device message, we suggest you always extract
the device with the ignition key turned to MAR,
or you stop playing (with the voice command
STOP) before you remove the USB device
from the vehicle's USB port. You have attempted to play a playlist,
but there are none on the USB device
The playlist is damaged or invalid
❒The playlist does not contain
multimedia files
❒The .wplfile is too big for the
Blue&Me™memory
❒The playlist does not contain
multimedia file references that are
found on your USB device
The digital audio is damaged or
invalid
The USB device has been removed
from the USB port on the vehicle
with the ignition key turned
to STOP
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:56 Pagina 67

71
Problem Probable cause Possible solution
With an iPod or USB memory stick,
the system continues playing the same
track and you need to press
the “forward” button to move
onto the next track
The battery of the iPod connected
to Blue&Me™is flat
The menu contains a specific item,
such as “Continuous play” or
“Repeat track”, that must be disabled.
To deactivate:
❒press the controls activation button
on the steering wheel
❒when prompted by the system, say
clearly “DEACTIVATE REPEAT
TRACK”
❒wait for voice confirmation from
the system, which will say
“REPEAT TRACK DEACTIVATED”
Remember that your iPod must have
some charge, or wait a few minutes
until the system recharges it The repeat single track function
may have been activated inadvertently
The vehicle, with the ignition key
turned to MAR, recharges the iPod
device unless the battery is
completely flat
604_39_206 DOBLO BLUE GB 1ed 17-09-2009 16:56 Pagina 71