jacking FIAT FREEMONT 2016 1.G Owners Manual

Tighten the lug nuts/bolts in a star pattern until each
nut/bolt has been tightened twice.
(fig. 169)
After 40 km check the lug nut/bolt torque to be sure
that all the lug nuts/bolts are properly seated against
the wheel.
WARNING!
To avoid the risk of forcing the vehicle
off t

he jack, do not tighten the lug nuts
fully until the vehicle has been lowered. Failure to
follow this warning may result in personal injury.
JACKING AND TIRE CHANGING (for
versions/markets, where
provided)
WARNING!
• Do not attempt to change a tire on the
si de

of the vehicle close to moving traf-
fic . Pull far enough off the road to avoid the
danger of being hit when operating the jack or
changing the wheel.
• Being under a jacked-up vehicle is dangerous.
The vehicle could slip off the jack and fall on you.
You could be crushed. Never put any part of your
body under a vehicle that is on a jack. If you need
to get under a raised vehicle, take it to a service
center where it can be raised on a lift .
• Never start or run the engine while the vehicle
is on a jack.
• The jack is designed to be used as a tool for
changing tires only.The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.
(fig. 169)
Torque Patterns
283
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

JACK LOCATION
The jack and jack-handle are stowed underneath a
cover in the rear storage bin in the cargo area.
(fig. 170)
SPARE TIRE LOCATION
The spare tire is stowed underneath the rear of the
vehicle and is held in place by means of a cable winch
mechanism.
PREPARATIONS FOR JACKING
1. Park the vehicle on a firm, level surface as far fromthe edge of the roadway as possible. Avoid icy or
slippery areas.
WARNING!
Do not attempt to change a tire on the
side of

the vehicle close to moving traf-
fic . Pull far enough off the road to avoid the
danger of being hit when operating the jack or
changing the wheel.
2. Turn on the Hazard Warning flashers.
3. Set the parking brake.
4. Place the shift lever in PARK (automatic transmis- sion) or in GEAR (manual transmission).
5. Turn OFF the ignition.
6. Block both the front and rear of the wheel diago- nally opposite of the jacking posi-
tion. For example, if changing the
right front tire, block the left rear
wheel.
NOTE: Passengers should not remain in the vehicle
when the vehicle is being jacked.
(fig. 170)
Jack Storage Location
284
KNOWINGYOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SER VICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

SPARE TIRE REMOVAL
NOTE:On seven-passenger models, fold the third-
row passenger seats flat. This will provide more space
when accessing the jacking tools and when operating
the winch mechanism.
1. Remove the jack-handle components 1, 2 and 3 from storage and assemble them. (fig. 171) NOTE:
Assemble components 2 and 3 by seating the
small ball at the end of component 2 in the small hole at
the end of component 3. This will lock these compo-
nents together. Assemble components 1 and 2 so that
the wheel nut socket at the end of component 1 faces
upward when seated on component 2. This will make it
easier to rotate the assembly when operating the
winch mechanism.
2. Fit the assembled jack-handle over the winch drive nut located in the jack storage area. Rotate the
jack-handle assembly counterclockwise until the
spare tire is on the ground with enough cable slack
to allow you to pull the spare tire out from under-
neath the vehicle.
The winch mechanism is designed for use
with the jack-handle only. Use of an air
wrench or other power tools is not rec-
ommended and it can damage the winch.
3. Pull the spare tire out from underneath the vehicle and raise it upright so the tire's tread is on the
ground.
(fig. 171)
Lowering/Raising Spare Tire
1 — Spare Tire Jack Handle
2 — Extension 1
3 — Extension 2
285
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

4. Tilt the retainer at the end of the winch cable andremove it from the center of the wheel. (fig. 172)
SPARE TIRE STOWAGE
NOTE: Refer to “Spare Tire Removal” for information
on assembling the winch tools.
1. Place the spare tire near to the winch cable. Hold the spare upright so that the tire's tread is on the
ground and the valve stem is at the top of the wheel
facing away from the rear of the vehicle.
2. Tilt the retainer at the end of the winch cable and drop it through the center of the wheel. Then place
the spare tire with the cable and retainer under-
neath the vehicle. 3. Fit the assembled jack-handle over the winch drive
nut. Rotate the jack-handle assembly clockwise to
raise the spare tire into the storage area. Continue
to rotate the jack-handle assembly until you hear
the winch mechanism click three times. It cannot be
over tightened. Push against the tire several times to
be sure it is held securely in place.
JACKING INSTRUCTIONS
WARNING!
Carefully follow these tire changing
warnin gs

to help prevent personal injury
or damage to your vehicle:
• Always park on a firm, level surface as far from
the edge of the roadway as possible before rais-
ing the vehicle.
• Turn on the Hazard Warning flashers.
• Block the wheel diagonally opposite the wheel
to be raised.
• Set the parking brake firmly and set an auto-
matic transmission in PARK; a manual transmis-
sion in REVERSE.
• Never start or run the engine with the vehicle
on a jack.
• Do not let anyone sit in the vehicle when it is on
a jack.
(Continued)
(fig. 172)Spare Tire Retainer
286
KNOWINGYOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SER VICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

WARNING! (Continued)
• Do not get under the vehicle when it is on a
jack. If you need to get under a raised vehicle,
take it to a service center where it can be raised
on a lift .
• Only use the jack in the positions indicated and
for lifting this vehicle during a tire change.
• If working on or near a roadway, be extremely
careful of motor traffic .
• To assure that spare tires, flat or inflated, are
securely stowed, spares must be stowed with the
valve stem facing the ground.
(fig. 173)
Do not attempt to raise the vehicle by
jacking on locations other than those
indicated in the Jacking Instructions for
this vehicle.
(fig. 174)
1. Remove the spare tire, jack, and jack-handle from stowage.
2. Loosen, but do not remove, the wheel nuts on the wheel with the flat tire. Turn the wheel nuts coun-
terclockwise one turn while the wheel is still on the
ground.
(fig. 173)
Jack Warning Label(fig. 174) Jacking Locations
287
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

3. Place the jack underneath the lift area that is closestto the flat tire. Center the jack saddle between the
drain flute formations on the sill flange. Turn the
jack screw clockwise to firmly engage the jack saddle
with the lift area of the sill flange.
(fig. 175) (fig. 176) (fig. 177) (fig. 178)
4. Raise the vehicle by turning the jack screw clock- wise with the jack handle. Raise the vehicle until the
tire just clears the road surface and enough clear-
ance is obtained to install the spare tire. Minimum
tire lift provides maximum stability.
(fig. 175)
Front Jacking Location
(fig. 176)Front Jack Engaged With Jack Handle
(fig. 177) Rear Jacking Location
288
KNOWINGYOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SER VICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

FRONT TOW EYE INSTALLATION
The front tow eye receptacle is located behind a door,
located on the right front bumper fascia. To install the
tow eye, open the door using the vehicle key or a small
screwdriver, and thread the tow eye into the recep-
tacle.
Insert the flat end of the jack handle through the eye
and tighten, refer to “Jacking and Tire Changing” for
further information. The tow eye must be fully seated
to the attaching bracket through the lower front fascia
as shown. If the tow eye is not fully seated to the
attaching bracket, the vehicle should not be towed.
(fig. 195)
REAR TOW EYE INSTALLATION
The rear tow eye receptacle is located behind a door,
located on the left rear bumper fascia.
To install the tow eye, open the door using the vehicle
key or a small screwdriver, and thread the tow eye into
the receptacle.
Insert the flat end of the jack handle through the eye
and tighten, refer to “Jacking and Tire Changing” for
further information. The tow eye must be fully seated
to the attaching bracket through the lower rear fascia
as shown. If the tow eye is not fully seated to the
attaching bracket, the vehicle should not be towed.
(fig. 196)
(fig. 195)Front Tow Eye Installed(fig. 196) Rear Tow Eye Installed
317
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND

CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Instrument Panel and Controls..................6
Instrument Panel Cover . . . ..................357
Instrument Panel Lens Cleaning ................358
Interior Appearance Care . . . .................357
Interior Fuses . . . . . . . . . . ..................308
Interior Lights .............................96
Intermittent Wipers (Delay Wipers) ..............98
Intervention Regeneration Strategy ..............344
Introduction ...............................1
Jacking Instructions . . ...................... .286
Jack Location ........................ .283, 284
Jack Operation . . . . . . . . ...................286
Jump Starting . . . . . . . ..................... .279
Key Fo b Programming Additional Key Fobs ..............14
Programming Additional Transmitters ...........14
Key-In Reminder . . . . . . . . ...................10
Keyless Enter-N-Go .................... .123, 238
Keyless Entry System . . . . . . ..................13
Keyless Go ................................8
Key, Programming . . . . . . . ...................12
Key, Replacement . . . . . . . . . ..................12
Keys....................................8
Key, Sentry (Immobilizer) . . ...................11
Lane Change and Turn Signals ..................95
Lane Change Assist . . . . . . ...................95
Lap/Shoulder Belts ........................ .194
Latches. ............................... .236
Hood .............................. .136
Lead Free Gasoline ........................ .379Leaks, Fluid
............................. .236
Leveling, Headlight ..........................92
LifeofTires..............................376
Liftgate.................................130
Liftgate Window Wiper/Washer ................101
Light Bulbs .......................... .236, 300
Lights .............................. .92, 236
Airbag ....................... .213, 235, 273
Anti-Lock ........................... .143
Anti-Lock Warning ..................... .278
Automatic Headlights .....................92
Back-Up ............................ .305
Brake Assist

Warning .................... .147
Brake Warning ........................ .276
Bulb Replacement ...................... .301
Courtesy/Reading ........................96
Dimmer Switch, Headlight ..................95
Electronic Stability Program (ESP) Indicator ......147
Exterior ............................. .236
Fog .......................... .94, 274, 302
Hazard Warning Flasher .................. .107
Headlight Leveling ........................92
Headlights ......................... .92, 301
Headlights On Reminder ...................94
Headlights On With Wipers .............93, 100
Headlight Switch .........................92
High Beam ..................... .95, 274, 301
High Beam Indicator .................... .274
High Beam/Low Beam Select .................95
Illuminated Entry ........................97
Instrument Cluster ................... .92, 273
Intensity Control ........................96
Interior ...............................96
396
KNOWING
YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICINGAND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Monitor, Tire Pressure System.................151
Multi-Function Control Lever ...................95
Navigation System (Uconnect® gps) ..........165, 166
New Vehicle Break-In Period ..................237
Occupant Restraints ....................... .192
Octane Rating, Gasoline (Fuel) ..............379, 385
Odometer . . . .......................... .275
Oil Change Indicator . . . . . . . ..............28, 275
Oil Change Indicator, Reset . . . ..............28, 275
Oil, Engine . . . . . . . . . . . . . ..............336, 385
Capacity . . . . . ....................... .384
Change Interval ..................... .28, 337
Checking ............................ .336
Dipstick . . . . . . . . ..................... .336
Disposal ............................ .338
Filter ............................... .385
Filter Disposal . . . . . ................... .338
Recommendation . . . . . ..................384
Viscosity . . . . . . . . . . . . . .............337, 384
Onboard Diagnostic System ...................149
Operating Precautions . . . . . .................149
Operator Manual (Owner's Manual) ...............3
Outside Rearview Mirrors . . . ..................66
Overhead Console ........................ .105
Owner's Manual (Operator Manual) ...............3
Paint Care. . . . . . . . . . . . ...................355
Parking Brake . .......................... .242
Passenger Seat Back Tilt (Easy Entry System) ........60
Passing Light . . . ...........................95
Pets, Transporting . . . . .................... .233Placard, Tire and Loading Information
............366
Power Brakes .............................. .140
Distribution Center (Fuses) ................310
Door Locks .......................... .120
Mirrors ...............................67
Outlet (Auxiliary Electrical Outlet) ...........112
Seats ................................48
Steering ............................. .150
Sunroof ............................. .117
T

ransfer Unit ......................... .354
Windows ............................ .127
Power Transfer Unit ....................... .354
Preparation for Jacking ..................... .284
Pretensioners Seat Belts ............................ .199
Programming Transmitters (Remote Keyless Entry) ....13
Radiator Cap (Coolant Pressure Cap) ............348
Radio Operation ......................... .190
Radio Remote Controls ..................... .167
Radio (Sound Systems) ..................... .167
Rear Air Conditioning .................... .76, 86
Rear Axle (Differential) ..................... .354
Rear Camera ............................ .165
Rear Cupholder .......................... .115
Rear Drive Assembly ...................... .354
Rear Fog Lights .......................... .278
RearLiftgate............................ .130
Rear Park Assist System .................... .159
Rear Seat, Folding ....................... .57, 62
RearviewMirrors...........................66
Rear Window Defroster .................... .102
398
KNOWING
YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICINGAND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS