ESP FIAT PANDA 2007 169 / 2.G Owners Manual

Dear Customer,
Thank you for selecting Fiat and congratulations on your choice of a Fiat Panda.
We have written this handbook to help you get to know all your new Fiat Panda’s features and use it in the best possible way.
You should read it right through before taking the road for the first time. You will find information, tips and important warnings re-
garding the driving of your car to help you derive the maximum from your Fiat Panda’s technological features.
You are recommended to read carefully the warnings and indications, marked with the respective symbols, at the end of the page:
personal safety;
the car’s wellbeing;
environmental protection.
The enclosed Warranty Booklet lists the services that Fiat offers to its Customers:
❒the Warranty Certificate with terms and conditions for maintaining its validity
❒the range of additional services available to Fiat Customers.
Best regards and good motoring!
This Owner Handbook describes all Fiat Panda versions. As a consequence, you should consider only the
information which is related to the engine and bodywork version of the car you purchased.
001-031 Panda New GB 21-06-2007 13:47 Pagina 1

MUST BE READ!

K
REFUELLING
Petrol engines: only refuel with unleaded petrol with octane rating (RON) not less than 95.
Diesel engines: only refuel with diesel fuel for motor vehicles (EN 590 Specification).
The use of other products or mixtures may irreparably damage the engine with invalidation of the warranty due to
the damage caused.
ENGINE STARTING
Petrol engines: make sure that the handbrake is engaged; set the gearshift lever to neutral; fully depress the clutch
without pressing the accelerator, then turn the ignition key to AVV and release it as soon as the engine has started.
Diesel engines: make sure that the handbrake is engaged; set the gearshift lever to neutral; fully depress the clutch
without pressing the accelerator, then turn the ignition key to MAR and wait for the warning lights
Yand mto
go off; turn the ignition key to AVV and release it as soon as the engine has started.
PARKING ON FLAMMABLE MATERIAL
While working, the catalyst develops a very high temperature. Do not park the car over grass, dry leaves, pine nee-
dles or any other inflammable materials.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that allows continuous diagnosis of the components correlated with emissions to en-
sure better respect for the environment.
001-031 Panda New GB 21-06-2007 13:47 Pagina 2

4
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLSDASHBOARD ...................................................................... 5
SYMBOLS ............................................................................... 7
THE FIAT CODE SYSTEM ................................................. 7
THE KEYS .............................................................................. 8
INSTRUMENT PANEL ........................................................ 13
INSTRUMENTS..................................................................... 16
DIGITAL DISPLAY ............................................................... 18
MULTIFUNCTION DISPLAY ............................................ 19
RECONFIGURABLE MULTIFUNCTION DISPLAY .... 21
TRIP COMPUTER ................................................................ 29
SEATS....................................................................................... 32
HEAD RESTRAINTS............................................................. 33
STEERING WHEEL............................................................... 35
REARVIEW MIRRORS......................................................... 35
HEATING AND VENTILATION...................................... 37
MANUAL CLIMATE CONTROL SYSTEM .................... 41
AUTOMATIC CLIMATE CONTROL SYSTEM ............. 44
EXTERNAL LIGHTS............................................................. 48
WINDOW WASHING....................................................... 49
CEILING LAMP...................................................................... 50
CONTROLS .......................................................................... 52
INTERIOR FITTINGS .......................................................... 53SUNROOF ............................................................................. 55
DOORS .................................................................................. 57
POWER WINDOWS/WINDOW WINDERS .............. 59
BOOT ...................................................................................... 62
BONNET................................................................................. 63
ROOF RACK/SKI RACK .................................................... 65
HEADLIGHTS........................................................................ 65
ABS SYSTEM ......................................................................... 67
ESP SYSTEM ........................................................................... 69
EOBD SYSTEM ..................................................................... 72
“DUALDRIVE” ELECTRIC POWER STEERING SYSTEM 72
PARKING SENSORS ........................................................... 74
SOUND SYSTEM.................................................................. 76
AT THE FILLING STATION.............................................. 78
PROTECTING THE ENVIRONMENT............................. 79
DD D
A A
S S
H H
B B
O O
A A
R R
D D
A A
N N
D D
C C
O O
N N
T T
R R
O O
L L
S S
001-031 Panda New GB 21-06-2007 13:47 Pagina 4

KEY WITH REMOTE CONTROL
(where provided) fig. 6 - fig. 6a
The metal insert Aoperates:
❒the ignition switch;
❒the door and the tailgate locks;
❒the switch to deactivate the passenger’s
air bag (where provided).
Press button Bto open/to close the met-
al insert.
fig. 6F0G0681m
9
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
KEY WITHOUT REMOTE
CONTROL fig. 5
The metal insert Aoperates:
❒the ignition switch;
❒the door and the tailgate locks;
❒the switch to deactivate the passenger’s
air bag (where provided).
fig. 4F0G0679mfig. 5F0G0680m
All the keys and the CODE
card must be handed over to
the new owner when selling
the car.
Button B should only be
pressed when the key is
away from the body, in particular
from the eyes and from objects that
can be spoilt (e.g. clothes). Make sure
the key can never be touched by oth-
ers, especially children, who may in-
advertently press the button.
WARNING
001-031 Panda New GB 21-06-2007 13:47 Pagina 9

19
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
MULTIFUNCTION
DISPLAY
STANDARD SCREEN fig. 23
The standard screen shows the following
indications:
AHeadlight aiming position (only with
dipped beam headlights on).
BClock.
COdometer (covered km or miles). WARNING LIGHT TEST fig. 22
The following warning lights are tested:
❒handbrake on/low brake fluid level;
❒ABS and EBD systems (where provid-
ed);
❒ESP system (where provided);
❒“Dualdrive” electrical power steering
failure (where provided).
The test is automatically run when the ig-
nition key is turned to MARand during
normal operation when a fault is signalled.
At the end of the initial warning light test,
the message “LEd Error” will flash on the
display for 10 seconds if a faulty warning
light is found.
fig. 22F0G0185mfig. 23F0G0016m
NoteWith key removed (when opening
one of the front doors) the display will
turn on and show for a few seconds the
clock and the km or mi covered.
001-031 Panda New GB 21-06-2007 13:47 Pagina 19

20
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SETTING THE CLOCK fig. 25
To adjust the time, press button Ato in-
crease minutes, button Bto decrease min-
utes. Every press on the button increas-
es or decreases by one unit. Keeping the
corresponding button pressed obtains au-
tomatic fast increase or decrease. When
you are near the required value, release
the button and complete adjustment with
single presses.
fig. 25F0I0142m
WARNING LIGHT TEST fig. 26
The following warning lights are tested:
❒handbrake on/low brake fluid level;
❒ABS and EBD systems (where provid-
ed);
❒ESP system (where provided);
❒“Dualdrive” electrical power steering
failure.
fig. 26F0G0152m
The test is automatically run when the key
is turned to MARand during normal op-
eration when a fault is signalled. At the end
of the initial warning light test, the mes-
sage LEd Err will flash on the display for
10 seconds if a faulty warning light is found.
001-031 Panda New GB 21-06-2007 13:47 Pagina 20

23
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Day
Year
MODE
briefly
press
button
Month
Deutsch
Português
English
Español
Français
Italiano
Nederland
Polski
Example:
SERVICEEXIT MENUTRIP B DATA
SET TIME
SET DATE
SEE RADIO
AUTOCLOSE
UNITS
LANGUAGE BUZZER VOLUME BUTTON VOL.SPEED LIM.
fig. 29Example:
+
–
– +
+
–
+
+–
–
+++
–––
++
– –+ +
–MODE
briefly
press
button
Briefly press button MODEto start surfing from the
standard screen. To surf the menu use buttons +or –.
NoteFor safety reasons, when the car is running, it is
possible to access only the reduced menu (for setting
the “Beep limit”). When the car is stationary access to
the whole menu is enabled. On cars provided with the
Connect Nav+ system, many functions are displayed on
the navigator display.
F0G1235g
– –
001-031 Panda New GB 21-06-2007 13:47 Pagina 23

38
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
not to use it for long periods, especially
if there several people in the car.
IMPORTANT The inside air recirculation
system makes it possible to reach the re-
quired “heating” or “cooling” conditions
faster. Do not use the air recirculation
function on rainy/cold days as it could con-
siderably increase the possibility of the
windows misting inside.
Air distribution knob D
¥to convey air to the centre and side
vents;
μto warm the feet and convey cooler
air to the dashboard vents;
wto heat with outside harsh tempera-
ture: close central and side vents to
convey as much air as possible to the
feet;
≤to warm the feet and at the same time
demist the windscreen;
-for quick windscreen demisting.VENTILATION
To ventilate the passenger’s compartment
properly proceed as follows:
❒central and side vents: completely open;
❒knob Aturned to blue section;
❒knob Cturned to U;
❒knob Dturned to ¥;
❒
knob Bturned to the required speed.
HEATING
Proceed as follows:
❒knob Aturned to red section;
❒knob Dturned to the required symbol;
❒knob Bturned to the required speed. CONTROLS fig. 45
Air temperature knob A (mixing
hot and cold air)
Red section = hot air
Blue section = cold air
Fan activation /speed adjustment
knob B
0= fan off
1-2-3 = fan speed
-= fan top speed
Air recirculation on/off knob C
U= outside air intake
T= inside air recirculation
This function is particularly useful when
the outside air is heavily polluted (in a traf-
fic jam, tunnel etc.). However, it is better
fig. 45F0G0022m
032-059 Panda New GB 21-06-2007 13:48 Pagina 38

41
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IIN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Air recirculation on/off knob C
U= outside air intake
T= inside air recirculation
This function is particularly useful when
the outside air is heavily polluted (in a traf-
fic jam, tunnel etc.). However, it is better
not to use it for long periods, especially
if there several people in the car.
IMPORTANT The inside air recirculation
system makes it possible to reach the re-
quired “heating” or “cooling” conditions
faster. Do not use the air recirculation
function on rainy/cold days as it could con-
siderably increase the possibility of the
windows misting inside.Air distribution knob D
¥air flow from central vents and side
outlets;
μto warm the feet and keep the face
cool (“bilevel” function);
wto speed up passenger compartment
warming;
≤to warm the passenger compartment
and at the same time demist the wind-
screen;
-to demist and defrost the windscreen
and front side windows.
VENTILATON
To ventilate the passenger’s compartment
properly proceed as follows:
❒central and side vents completely open;
❒turn knob Ato the blue section;
❒turn knob Cto U;
❒turn knob Dto ¥;
❒
turn knob Bto the required speed.
MANUAL CLIMATE
CONTROL SYSTEM
(where provided)
CONTROLS fig. 47
Air temperature knob A
(mixing hot and cold air)
Red section = hot air
Blue section = cold air
Fan activation and climate control
system on/off knob B
0= fan off
1-2-3= fan speed
-= top fan speed
Press the knob to turn the climate control
system on, the knob led will turn on. Press
it again to turn it off, the knob led will turn
off.
fig. 47F0G0600m
032-059 Panda New GB 21-06-2007 13:48 Pagina 41

45
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IIN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Button T - D
Air recirculation on/off
This function is particularly useful when
the outside air is heavily polluted (in a traf-
fic jam, tunnel, etc.).
Button led on = recirculation on.
Button led off = recirculation off.
With low temperatures or compressor
off, air recirculation is deactivated to pre-
vent window misting up.
IMPORTANT It is inadvisable to use air
recirculation on cold days as it would con-
siderably increase the possibility of win-
dows misting up inside.
During AUTOoperation, due to safety rea-
sons, after long recirculation activation (over
25 minutes) the system will deactivate au-
tomatically air recirculation for 1 minute to
enable outside air inlet.
Buttons ÕÔ- E
Temperature setting
Pressing button Õwill raise the passen-
ger’s compartment temperature up to HI
value (maximum heating power).Pressing button Ôwill lower the passen-
ger’s compartment temperature down to
LO value (maximum cooling power).
HI function
This functions can be switched on when
you wish to heat the passenger compart-
ment as quickly as possible; air distribu-
tion and fan speed are controlled by the
system.
To turn this function off, set the required
temperature.
IMPORTANT If the system fluid is not
warm enough, top fan speed will not be
activated immediately to prevent air not
warm enough from entering the passen-
ger compartment.
LO function
This function can be switched on when
you wish to cool the passenger compart-
ment as quickly as possible; with this func-
tion switched on the compressor will be
turned on (if off) whereas air distribution
and fan speed are controlled by the sys-
tem.
To turn this function off, set the required
temperature.
IMPORTANT With the function switched
on, however, all the manual settings can
be made. Button OFF - C
Switching the climate control
system off
Press button OFFto turn the system off.
When turned off the system conditions are
the following:
❒all leds off;
❒temperature display off;
❒air recirculation off;
❒compressor off;
❒fan off.
Under this condition, air recirculation can
be turned on or off without activating the
system.
IMPORTANT The system will store the
settings (except recirculation) performed
before turning off and will resume them
when pressing any button (if the function
corresponding to the button pressed is off
it will be turned on; if on it will be kept ac-
tive). Press AUTOto turn the system in
automatic mode.
032-059 Panda New GB 21-06-2007 13:48 Pagina 45