bulb FIAT PANDA 2009 169 / 2.G Owners Manual

132
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
ESP SYSTEM FAILURE (amber)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds.
If the warning light does not go off or stays on together
with the LED on the button ASR OFF when travelling, con-
tact a Fiat Dealership.
On some versions the display shows the dedicated message.
NOTE The warning light flashing when driving indicates
that the ESP system is active.
á
GENERIC FAILURE INDICATION
(amber)
The warning light turns on in the following cir-
cumstances.
Engine oil pressure sensor failure
The warning light turns on when failure is detected in en-
gine oil pressure sensor. Contact a Fiat Dealership to have
the failure fixed as soon as possible.
Water in diesel fuel filter
See what described for warning light
c.
Inertia fuel cut-off switch tripped
The warning light comes on when the inertia fuel cut-off
switch is triggered. The display shows the dedicated
message.
è
EXTERNAL LIGHT FAILURE (amber)
The warning light will come on (some versions
only) when a failure to one of the following lights
is detected:
– side lights;
– brake lights (third brake light excluded);
– rear fog lights;
– direction indicators;
– number plate lights.
The failure referring to these lights could be: one or more
blown bulbs, a blown protection fuse or an electric con-
nection cut-off.
The display shows the dedicated message.
W
REAR FOG LIGHTS (amber)
The warning light turns on when the rear fog
lights are turned on.
4
HEATED REAR WINDOW (amber)
The warning light turns on when switching the
heated rear window on.
(
123-134 PANDA EN 7-10-2009 13:49 Pagina 132

149KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CHANGING A BULBGENERAL INSTRUCTIONS❒
Before changing a bulb check the contacts for oxidation;
❒
burnt bulbs must be replaced by others of the same type
and power;
❒
always check the headlight beam aiming after changing
a bulb;
❒
when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing fus-
es” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or
do not take the system technical specifications in-
to account can cause malfunctions leading to the
risk of fire.
WARNING
Halogen bulbs contain gas under pressure;
if they break, glass fragments may be dis-
persed.
WARNING
When handling halogen bulbs, only touch
the metal part. If the transparent bulb is
touched with the fingers, its lighting inten-
sity is reduced and life of the bulb may be com-
promised. In the event of accidental contact, wipe
the bulb with a cloth moistened with alcohol
and leave it to dry.
IMPORTANT The headlight inner surface might be slight-
ly misted: this should not be considered irregular rather
a natural phenomenon due to low temperature and the air
humidity level. Misting will disappear as soon as the head-
lights are turned on. The presence of drops inside the
headlights indicates infiltration of water. Contact a Fiat
Dealership.
Where possible, it is advisable to have bulbs
changed at a Fiat Dealership. The correct
operation and aiming of the outer lights are
absolutely important to the safety of the car and
its passengers and the subject of specific laws about
road traffic.
135-168 PANDA EN 7-10-2009 14:07 Pagina 149

150KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0118m
fig. 140
TYPES OF BULBS fig. 140
Various types of bulbs are fitted to your car:
A Glass bulbs: they are pressure-fit. Pull to remove.
B Bayonet-type bulbs: to remove this type of bulb from
its holder, press the bulb and turn it counter-clockwise.
C Tubular bulbs: release them from their contacts to re-
move.
D Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
E Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
135-168 PANDA EN 7-10-2009 14:07 Pagina 150

151KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
H4
H4
W5W
PY21W
W5W
PY21W
P21/5W
P21W
P21W
C5W
W5W
C5W
H1
W5W
60/55
60/55
5
21
5
21
21/5
21
21
5
5
5
55
5
D
D
A
B
A
B
B
B
B
C
A
C
E
A
Bulbs Type Power Re. figure 140Main beamDipped beamFront side lightsFront direction indicatorsSide direction indicatorsRear direction indicatorsStop/tail lightsReversing lightsRear fog lightsCeiling lightBoot lightNumber plate lightFog lightsThird stop
135-168 PANDA EN 7-10-2009 14:07 Pagina 151

152KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0089m
fig. 141
F0Z0091m
fig. 143
F0Z0090m
fig. 142
To change the direction indicator bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder D-fig. 142 and remove it (it is pres-
sure-fit);
CHANGING AN EXTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
FRONT LIGHT UNIT
To change the side light bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder C-fig. 142 and remove it (it is pres-
sure-fit);
❒
remove the burnt bulb E-fig. 143 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 152

153KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0092m
fig. 144
F0Z0094m
fig. 146
F0Z0093m
fig. 145
❒
remove the burnt bulb F-fig. 144 and fit the new one;
❒
refit by reversing the above mentioned operations.
To replace the main/dipped beam light bulb, proceed as
follows:
❒
release the clip A-fig. 141 and remove the cap B;
❒
remove the connector G-fig. 145;
❒
release the bulb-holder clip H-fig. 145;
❒
remove the burnt bulb I-fig. 146 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 153

154KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0095m
fig. 147
F0Z0227m
fig. 149
F0Z0604m
fig. 148
FRONT FOG LIGHTS
(for versions/markets where provided)
To change the halogen bulb, proceed as follows:❒
undo the two screws A and B-fig. 149 for fog light fas-
tening on the bumper and take out trim and fog light,
disconnecting the connector;
❒
loosen the cover C-fig. 150 and remove the connec-
tor D;
❒
release the clip E-fig. 151 and remove the bulb F;
❒
refit by reversing the above mentioned operations. SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒
push the lamp lens A-fig. 147 in the car running direc-
tion (it is pressure-fit);
❒
remove the bulb B-fig. 148 and replace it;
❒
remove the lamp lens.
135-168 PANDA EN 7-10-2009 14:07 Pagina 154

155KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0229m
fig. 151
TOP
OFF
ON
F0Z0228m
fig. 150
F0Z0097m
fig. 153
F0Z0096m
fig. 152
❒
loosen the four screws B-fig. 153 from their housings
and remove the bulb-holder C;
❒
remove the bulbs, pushing them slightly and rotating
counter-clockwise;
❒
refit by reversing the above mentioned operations. REAR LIGHT UNIT
To change the bulb proceed as follows:
❒
loosen the three screws A-fig. 152 from their seats, pull
gently outwards until releasing the whole headlight from
the three clips (press-fit), then release the connector;
135-168 PANDA EN 7-10-2009 14:07 Pagina 155

156KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0099m
fig. 155
F0Z0098m
fig. 154
F0Z0100m
fig. 156
NUMBER PLATE LIGHTS
To change the bulb, proceed as follows:❒
use a screwdriver to remove the retaining spring as
shown fig. 155 and remove the lens A-fig. 156; take out
the bulb B from the bulb-holder;
❒
replace the 12 V - 5 W pressure-fit bulb in the bulb-
holder and refit the lens. Figure 154
D 12 V – 21 W bulb for reversing light on right light unit;
❒
rear fog light on left light unit;
❒
on right-hand drive versions, reversing light in the
left rear light unit and rear fog lamp in the right rear
light unit;
E 12 V – 21 W bulb for the direction indicators;
F 12 V – 21/5 W double-light bulb for stop light and tail
lights.
135-168 PANDA EN 7-10-2009 14:07 Pagina 156

157KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0211m
fig. 158
F0Z0101m
fig. 157
F0Z0210m
fig. 159
❒
release the clip C-fig. 158 and remove the bulb unit from
the lens unit;
❒
replace the pressure-fit burnt out bulb D;
❒
refit by reversing the above mentioned operations. THIRD STOP LIGHTS
To change one or more bulbs, proceed as follows:
❒
undo the two screws A-fig. 157 and remove the whole
cover;
❒
disconnect the connector B-fig. 159 and remove the
light unit;
135-168 PANDA EN 7-10-2009 14:07 Pagina 157