front light FIAT PUNTO EVO 2010 1.G Repair Manual

191
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0152mfig. 170
A
A
B
F0U0151mfig. 169
DIRECTION INDICATORS
Front fig. 169
To change the bulb, proceed as follows:
❒steer the right/left wheel inwards;
❒turn the catch A-fig. 169, then lift off the access lid B;
D
F0U0153mfig. 171
❒remove the bulb holder cover C-fig. 170 by turning it
anti-clockwise;
❒remove the bulb D-fig. 171 by pushing it in gently and
turning anti-clockwise (“bayonet” clamping), then re-
place it;
❒refit the bulb holder cover C-fig. 170 by turning it clock-
wise and locking it properly;
❒close the lid B-fig.169 then tighten the catch A.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 191

192
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
A
F0U0526mfig. 173/b
❒loosen the fixing screws C and remove the headlamp;
❒remove the bulb A-fig.173/b by rotating it counter-
clockwise and disconnect the electrical connector.
F0U0280mfig. 172
Side fig. 172
To change the bulb, proceed as follows:
❒slide the lens A towards the front of the car to press
in the internal catch B, then pull the unit outwards;
❒turn the bulb holder C anti-clockwise, extract bulb D
and replace it;
❒refit the bulb holder C into the lens by turning it clock-
wise;
❒refit the unit making sure the internal catch B clicks in-
to place.
FRONT FOG LIGHTS
(for versions/markets where provided)
To replace the bulb:
❒loosen the screw A-fig.173/a and remove the protec-
tion template B;
C
AC
B
C
F0U0525mfig. 173/a
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 192

195
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0160mfig. 179
F0U0159mfig. 178
❒change the bulb fig.179 by releasing it from the side
contacts and making sure the new bulb is correctly fas-
tened between these contacts;
❒refit the snap-fitted lens unit.
F0U0163mfig. 180
CHANGING AN INTERIOR BULB
For the type of bulb and relevant power rating, see
“Changing a bulb”.
FRONT CEILING LIGHT
Proceed as follows to replace the bulbs:
❒manipulate the points shown by the arrows and remove
light A-fig. 180;
❒ open the protective flap B-fig. 181;
❒replace bulbs C-fig. 181 by releasing them from the side
contacts and making sure that new bulbs are correctly
clamped between these contacts;
❒close the flap B-fig. 181 and fasten the courtesy light
A-fig. 180 in its housing, making sure it is locked in cor-
rectly.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 195

203
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
7.5
7.5
5
5
10
5
20
20
20
20
5
5
7.5 1
8
13
2
5
11
4
6
14
7
12
3
10
FUSE TABLE
Dashboard fuse box fig. 190
DEVICESFUSE AMPS
Right dipped beam headlight
Lift dipped beam headlight, headlamp alignment corrector
INT/A supply for switch coils on engine fuse box
and switch coils on body computer control unit
Front ceiling light, rear ceiling light, visor lights,
door marker lights, boot light, glove box light
Supply and battery for EOBD diagnostic plug, automatic climate
control system control unit, alarm, sound system, convergence control unit
INT supply for instrument panel, switch on brake pedal
(N.O. contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot
unlocking motor
Windscreen/rear window washer pump
Electric window motor on driver-side front door
Electric window motor on passenger-side front door
INT supply for dashboard control lights, parking control unit,
tyre pressure measurement control unit, electric wing mirror movement,
rain sensor, sunroof control unit, My Port infotelematic system socket,
electric rear view mirror
Instrument panel
INT supply for brake pedal switch (NC contact), clutch pedal switch,
interior heating unit, convergence control unit, sound system capabilities,
voltage stabiliser control unit, reverse light on rear bumper,
water sensor on diesel filter, glow plug heating control unit, airflow meter,
brake booster sensor, switch coils on engine compartment fuse box
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 203

205
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
17
14
01
03
04
15
10
16
08
07
05
11
13
09
06
0220
7.5
–
–
10
–
20
–
10
–
15
20
5
10
–
– Boot fuse box fig. 194
DEVICESFUSE AMPS
Sunroof opening system
Alarm system management control unit
Spare
Spare
Electric lumbar movement on driver’s seat
Spare
Electric windows system (motor, control unit) on right-hand door
Spare
Driver’s seat heater control unit
Tow hook system (capability for after-sale fuse assembly)
Boot socket
Electric windows system (motor, control unit) on left-hand door
TPMS (tyre pressure monitoring system) control unit
Front passenger seat heater control unit
Spare
Spare
175-210 PUNTO FL EN 4ed 20-01-2010 15:10 Pagina 205

209
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TOWING THE CAR
The tow ring provided with the car is housed in the tool
box under the boot carpet.
fig. 197aF0U0179m
F0U0180mfig. 197b
FASTENING THE TOW RING fig. 197a-197b
Proceed as follows:
❒release the cap A;
❒take the tow ring B from its support;
❒fully tighten the ring on the rear or front threaded pin.
175-210 PUNTO FL EN 4ed 20-01-2010 15:10 Pagina 209

210
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
The brake booster and power steering will
not work while the vehicle is being towed.
You will therefore need to apply more force to the
brake pedal and steering wheel. Do not use bendy
cables for towing and avoid jerking. Make sure not
to damage parts in contact with the car while tow-
ing. When towing the vehicle, be sure to respect
the specific rules of the highway code specifical-
ly in relation to the towing device and the be-
haviour to maintain on the road.
WARNING
Clean the threaded housing throughly be-
fore fastening the tow ring. Make sure that
the ring is securely fastened before towing the car.
WARNING
During towing, do not start up the engine.
WARNING
Before towing, switch off the steering lock
(see “Ignition” in the “Dashboard and con-
trols” section). The brake booster and power
steering will not work while the vehicle is being
towed. You will therefore need to apply more
force to the brake pedal and steering wheel. Do
not use bendy cables for towing and avoid jerking.
Make sure not to damage parts in contact with
the car while towing. Respect the rules of the high-
way code when towing the car, specifically in re-
lation to the towing device and road conduct.
WARNING
The front and rear tow hooks should be
used only for emergency operations on the
road. You are allowed to tow the car for short dis-
tances using an appropriate device in accordance
with the highway code (a rigid bar), to move the
vehicle on the road in readiness for towing or
transporting via a breakdown vehicle. Tow hooks
MUST NOT be used to tow vehicles off the road
or where there are obstacles and/or for towing op-
erations using cables or other non-rigid devices.
Respecting the above conditions, towing must
take place with the two vehicles (one towing, the
other towed) aligned as much as possible along
the same centre line.
WARNING
175-210 PUNTO FL EN 4ed 20-01-2010 15:10 Pagina 210

●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●●
●●
●●
●● ●
●● ●● ● ●
212
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SCHEDULED SERVICING PLAN
EURO 4/EURO 5 PETROL AND EURO 4 DIESEL VERSIONS
Thousands of kilometres 30 60 90 120 150 180
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlamps, direction indicators,
hazard warning lights, boot, passenger compartment, glove box,
instrument panel warning lights, etc.)
Check operation of windscreen washer system and adjust nozzles
if necessary.
Check windscreen/rear window wiper blade position/wear
Check conditions and wear of front/rear disc brake pads
(for versions/markets where provided) and operation of pad wear indicator
Check condition and wear of rear drum brake linings
Visually inspect the conditions of: bodywork,
underbody protection, pipes and tubes
(exhaust – fuel – brakes), rubber parts (boots, sleeves, bushes, etc.)
Check cleanliness of bonnet and boot locks, and the cleanliness
and lubrication of linkages
Check and, if necessary, top up fluid levels (brakes/hydraulic
clutch, windscreen washer, battery, engine coolant, etc.)
Check the handbrake lever stroke and adjust it, if necessary
Visually inspect the condition of accessory drive belt/s.
Visually inspect the condition of toothed timing belt
Check tension of accessory drive belt/s, and adjust if necessary
(versions 1.2 – 1.4 heated)
Check and, if necessary, adjust tappet clearance (1.2 8v – 1.4 8vversions)
Check exhaust gas emissions
211-234 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 212

214
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●●
●● ● ● ●
●● ● ● ●
●
EURO 5 DIESEL VERSIONS
Thousands of kilometres 35 70 105 140 175
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlamps, direction indicators, hazard warning lights,
boot, passenger compartment, glove box, instrument panel warning lights, etc.)
Check operation of windscreen washer system and adjust nozzles
if necessary
Check windscreen/rear window wiper blade position/wear
Check condition and wear of front disc brake pads and operation of pad
wear indicator
Check condition and wear of rear disc brake pads (1.6 Multijet versions)
Check condition and wear of rear drum brake linings (1.3 Multijet version)
Visually inspect the conditions of: bodywork, underbody protection,
pipes and tubes (exhaust - fuel - brakes), rubber parts (boots, sleeves, bushes, etc.)
Check cleanliness of bonnet and boot locks, as well as cleanliness and lubrication of linkages
Check and, if necessary, top up fluid levels (brakes/hydraulic clutch, windscreen washer,
battery, engine coolant, etc.)
Check the handbrake lever stroke and adjust it, if necessary
Visually inspect the condition of accessory drive belts
Check emissions/fumes
Check engine management system operation (via diagnostic socket)
Replace accessory drive belt/s
211-234 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 214

216
HEAVY USAGE OF THE VEHICLE
Should the car be used predominantly in one of the fol-
lowing particularly demanding conditions:
❒ trailer or caravan towing;
❒ dusty roads;
❒short (less than 7-8 km) and repeated journeys in sub-
zero temperatures;
❒frequently idling engine or long-distance, low-speed dri-
ving (e.g. door-to-door deliveries), or in the event of
long-term inactivity;
❒ in cities;
perform the following inspections more frequently than
shown on the Scheduled Servicing Plan:
❒ check condition and wear of front disc brake pads;
❒check cleanliness of bonnet and boot locks, as well as
cleanliness and lubrication of linkages;
❒visually inspect the conditions of: engine, gearbox, trans-
mission, pipes and tubes (exhaust – fuel – brakes), rub-
ber parts (boots, sleeves, bushes, etc.);
❒check battery charge and liquid level (electrolyte);
❒ visually inspect condition of accessory drive belts;
❒ check pollen filter and replace it, if required;
❒ check air filter and replace, if required.
REGULAR CHECKS
Every 1,000 km or before long journeys, check and, if nec-
essary, top up:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressures and conditions;
❒operation of lighting system (headlights, direction indi-
cators, hazard lights, etc.);
❒operation of the windscreen wiper/washer system, po-
sition and wear of the windscreen and rear window
wiper blades;
Check and top up, if required, the engine oil level every
3,000 km.
You are recommended to use PETRONAS LUBRICANTS
products, which have been designed and produced specif-
ically for Fiat cars (see table “Capacities” in the “Techni-
cal specifications” section).
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
211-234 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 216