FIAT ULYSSE 2009 2.G User Guide

GETTING TO KNOW YOUR CAR
10
1.Side vents
2.Left-hand stalk: headlight control
3.Horn
4.Instrument panel: odometer display and warning lights
5.Right-hand stalk, windscreen washer, rear window
washer and trip computer
6.Gear lever
7.Central vents
8.Revolution counter
9.Speedometer
10.Fuel gauge with low fuel warning light and engine
coolant temperature gauge with warning light showing
when the temperature is too high
11.Sound system/Infotelematic Connect system display
(for versions/markets, where provided)
12.Sound system/Infotelematic Connect system (for ver-
sions/markets, where provided)
13.Passenger air bag14.Glove compartment
15.Climate system automatic controls
16.Hazard lights
17.Cigar lighter
18.Glove compartment/Infotelematic Connect system re-
mote controls (for versions/markets, where provided)
19.Console
20.Ashtray and glove compartment
21.Ignition switch
22.Sound system controls on steering wheel
23.Document compartment
24.Driver air bag
25.Cruise control control lever
26.Headlight beam adjuster (Xeno light versions excluded)
27.ASR system on/off.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 10

GETTING TO KNOW YOUR CAR
11fig. 2
F0B0401b
THE FIAT CODE
SYSTEM
To further protect your vehicle from
attempted theft, it has been fitted with
an electronic engine immobiliser sys-
tem (called Fiat CODE) which is au-
tomatically activated when the ignition
key is removed. Each ignition key, in
fact, contains an electronic device,
which modulates a radio-frequency
signal emitted by a special aerial, built
into the ignition switch, during ignition.
The modulated signal is a “password”
with which the control unit recognis-
es the key. Engine ignition is enabled
only if the key is recognised by the sys-
tem.THE KEYS fig. 2
The following keys are supplied with
the car:
– two keys Aif the car is fitted with
remote central door locking system
and electronic alarm.
– two keys Bif the car is fitted with
remote central door locking system,
electronic alarm and powered side
sliding doors.The keys shall be used to:
– ignition switch;
– lock/unlock the driver and passen-
ger door
– operate remote door lock-
ing/unlocking
– operate the alarm system (for ver-
sions/markets, where provided)
– deactivate the passenger side airbag
– lock/unlock the fuel filler cap
– lock/unlock the glove compart-
ment.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 11

GETTING TO KNOW YOUR CAR
12
The key fig. 3, is fitted with 2 but-
tons:
A -to activate the central locking
system, the alarm and the localisation
function;
B -to activate the central unlocking
system and deactivate the alarm.By pressing button Athe so-called
“localisation” function is turned on: all
the passenger compartment lights and
direction indicators are switched on
for a couple of seconds. Such function
is recognised by the system up to a
distance of around 30 meters from the
vehicle.
The key is also fitted with a metal in-
sert Dwhich can be pushed inside the
key grip by pressing button C.
Press button Cagain to let it come
out from the key grip.When pressing the but-
ton C, take care to pre-
vent the metal insert
from causing harm or damage
when it comes out. The button C
should only be pressed when the
key is away from the body, in par-
ticular from the eyes and from
objects that can be spoilt (e.g.
clothes). Make sure the key can
never be touched by others, es-
pecially children, who may inad-
vertently press button C.
fig. 3
F0B0402b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 12

GETTING TO KNOW YOUR CAR
13
A CODE card fig. 5is provided with
the keys. This CODE card bears the
electronic code used by the Fiat
Dealershipswhenever the vehicle
cannot be started. The key fig. 4is fitted with 4 but-
tons:
A -to activate the central locking
system, the alarm and the localisation
function;
B -to activate the central unlocking
system and deactivate the alarm;
C -to lock/unlock the right-hand
side sliding door;
D -to lock/unlock the left-hand side
sliding door.
By pressing button Athe so-called
“localisation” function is turned on: all
the passenger compartment lights and
direction indicators are switched on
for a couple of seconds. Such function
is recognised by the system up to a
distance of around 30 meters from the
vehicle.
The key is also fitted with a metal in-
sert Fwhich can be pushed inside the
key grip by pressing button E.The remote control inside the key
works on radio-frequency.
IMPORTANTIn order to ensure
perfect efficiency of the electronic de-
vices contained inside the keys, they
should never be exposed to direct
sunlight. When pressing the but-
ton E, take care to pre-
vent the metal insert
from causing harm or damage
when it comes out. The button
E should only be pressed when
the key is away from the body, in
particular from the eyes and
from objects that can be spoilt
(e.g. clothes). Make sure the key
can never be touched by others,
especially children, who may in-
advertently press button E.The electronic compo-
nents inside the key may
get damaged if the key is
submitted to sharp knocks.
fig. 4
F0B0403b
Press button Eagain to let it come
out from the key grip.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 13

GETTING TO KNOW YOUR CAR
14
REPLACING THE KEY
BATTERIES fig. 6-7
If the doors do not lock and the di-
rection indicators do not come on
when the button on the remote con-
trol is pressed, replace the batteries
with others of the same time:
– open the metal insert;
– open the plastic casing Aby forc-
ing recess B;
– remove the printed circuit Cwith
the battery;
– extract the battery Dand replace
it respecting the polarity;
– refit the printed circuit Cwith the
battery facing inwards;
– close the plastic casing A.Since the electronic alarm absorbs
electricity, if you will not be using the
vehicle for more than a month, you
are advised to switch the system off
with the remote control. This will pre-
vent the battery from going flat. All the keys and the
CODE card must be
handed over to the new
owner when selling the car.
fig. 5
F0B0404b
This code is masked by a special
paint, which should be removed when
the CODE card is used. The CODE
card should therefore be kept in a safe
place and not in the vehicle.Used batteries pollute
the environment. Dispose
of them in the special
containers as specified by current
legislation or take them to your
nearest Fiat Dealership, which
will deal with their disposal. Do
not expose them to naked flames
and high temperatures. Keep out
of children’s reach.
fig. 6
F0B0440b
fig. 7
F0B0441b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 14

GETTING TO KNOW YOUR CAR
15
DUPLICATE KEYS
Go directly to your Fiat Dealer-
ship, taking all the keys in your pos-
session and the CODE card with you.
The codes of any keys that are not
available when the new storage pro-
cedure is carried out will be deleted
from the memory to prevent any lost
or stolen keys being used to start the
engine.
All the keys and the CODE card
must be handed over to the new own-
er when selling the car.OPERATION
When the ignition switch is turned
to Sthe Fiat CODE system deacti-
vates the engine control unit functions.
After the engine is started by turning
the key to M, the Fiat CODE system
control unit sends the code for the
function lock deactivation to the en-
gine control unit. The crypted and
varying code is sent only if the system
control unit has recognised the code
sent by the electronic device con-
tained in each ignition key, through the
signal emitted by a special aerial built
into the ignition switch.
If the code is not recognised, you are
recommended to turn the key to S
and then again to M; if the lock cannot
be deactivated, repeat the operation
with the other key provided with the
vehicle.If you are still not able to start the
engine contact a Fiat Dealership.
IMPORTANTEach key supplied
with the vehicle has its own code
which is different from all the others
and which must be stored in the mem-
ory of the system control unit. Con-
tact a Fiat Dealershipfor the new
key storage procedure, taking with
you the CODE card, a personal iden-
tity document and the vehicle owner-
ship documents.
The codes of any keys
that are not available
when the new storage
procedure is carried out will be
deleted from the memory when
all the keys are stored again, in
order to prevent any mislaid keys
being used to start the vehicle.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 15

GETTING TO KNOW YOUR CAR
16
ELECTRONIC
ALARM
(for versions/markets, where provided)
The vehicle is equipped with an elec-
tronic alarm with perimeter (external)
protection and volumetric (internal)
protection. To switch on the alarm,
press the button A-fig. 8on the re-
mote control.
This will be accompanied by the di-
rection indicator flashing and then the
red led on the dashboard A-fig. 9
flashing.
Door locking by turning the key
does not activate the alarm. When the alarm is triggered
The siren comes on, the direction in-
dicators and the headlights flash for
about 30 seconds when:
– - the doors, bonnet, boot or sun-
roof (for versions/markets, where
provided) are opened;
– a variation in the volume inside the
vehicle is experienced (do not leave the
windows open or animals inside the ve-
hicle when the alarm is switched on);
– if an attempt is made to neutralise
the alarm system without the remote
control.Switching the alarm system off
To switch the alarm system off, press
button B-fig. 8on the remote con-
trol.
The direction indicators will flash
rapidly for about 2 seconds.
If the alarm system has triggered, led
A-fig. 9will flash rapidly.
fig. 8
F0B0405b
fig. 9
F0B0003b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 16

GETTING TO KNOW YOUR CAR
17
Switching the volumetric
protection off
Before turning on the alarm system,
press button A-fig. 10, which can be
reached when the door is open, and
red led A-fig. 9, placed on the instru-
ment panel, will light up.
In this case only the perimeter pro-
tection (external) system will be ac-
tive.
Press the button A-fig. 9 again to re-
turn to the normal external and in-
ternal protection mode.Deactivation without
the remote control
Proceed as follows:
– open the door with the key (the
siren will come on);
– within 10 seconds, from when the
siren sounds, turn the ignition key to
Mand then press button A-fig. 10.
The siren will be switched off.
If it is necessary to repeat the oper-
ation, wait for the siren to come on.
PROGRAMMING THE SYSTEM
When your new vehicle is handed
over to you the electronic alarm will
have already been programmed by
your Fiat Dealership. Any subse-
quent programming should also be
carried out by a Fiat Dealership.REQUEST FOR ADDITIONAL
REMOTE CONTROLS
If you ever need a new remote con-
trol, go to your nearest Fiat Deal-
ership, taking with you all the vehi-
cle keys in your possession, the CODE
card, a personal identity document and
the vehicle ownership documents.
fig. 10
F0B0218b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 17

GETTING TO KNOW YOUR CAR
18
IGNITION SWITCH
fig. 11
The key can turn through 4 different
positions:
S -engine off, key can be removed
and the steering column is locked;
M -drive position;
D -starting the engine.When you get out of the
vehicle, always remove
the ignition key. This will
prevent anyone from accidental-
ly working controls. Remember
to apply the handbrake and, if the
vehicle is pointing uphill, first
gear. Put the vehicle into reverse
if it is pointing downhill. Never
leave children in the vehicle by
themselves.
STEERING COLUMN LOCK
To engage the lock:when the ig-
nition switch is in position S, remove
the ignition key and turn the steering
wheel until it locks.
To release the lock:move the
steering wheel slightly as you turn the
ignition key toM.Never remove the igni-
tion key while the vehicle
is moving. The steering
wheel would automatically lock
as soon as you tried to turn it.
This always applies, even when
the vehicle is being towed.
fig. 11
F0B0406b
If the ignition switch has
been tampered with (e.g.
someone has tried to
steal your vehicle), get a Fiat
Dealership to check it over be-
fore you start driving again.
It is absolutely forbidden
to carry out whatever af-
ter-market operation in-
volving steering system or steer-
ing column modifications (e.g.: in-
stallation of anti-theft Device)
that could badly affect perfor-
mance and safety, cause the lapse
of warranty and also result in
non-compliance of the car with
homologation requirements.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 18

GETTING TO KNOW YOUR CAR
19
DOORS10 km/h is reached, the doors and the
tailgate are automatically locked.
When the key is turned to M, the ac-
tivation of this function is signalled by
a sound (“beep”). Press and keep but-
ton A-fig.12 pressed for more than
3 seconds to deactivate the above
mentioned function.
SECOND ROW CONTROL
ELECTRIC DEACTIVATION
fig. 13
Next to the electric window lock-
ing/unlocking controls on the driver’s
side, there is button Awhich prevents
rear row controls from being used and
therefore windows, sunroof (for ver-
sions/markets, where provided) and
side sliding doors from being opened
by the passengers in the second row.FRONT DOORS
Opening/closing by hand from
the outside fig. 14
Opening:turn the key to position
1and pull the door handle in the di-
rection of the arrow.
Closing:close the door and turn the
key to position 2.
IMPORTANT Insert the key right
into the lock before turning it.
fig. 12
F0B0012b
fig. 13
F0B0013b
fig. 14
F0B0407b
Always use these locks
when transporting chil-
dren.
Before opening a door
make sure that the oper-
ation can be performed in
safety conditions.
A buzzer will sound to inform the
driver that the outside lights are on
when a door is opened and the igni-
tion key is removed. Switch off the
lights, close the door or start the en-
gine to stop the buzzer. The vehicle
is fitted with button A-fig. 12, placed
next to the front ceiling lamp, to
lock/unlock the doors from the inside.
The vehicle is delivered to the cus-
tomer with the ”autoclose” system on.
It means that when a speed above
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 19