ECU FORD BRONCO 1988 User Guide

47
*
[SR16415(BEF )04/95]
8. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode,
Figure 8.
*
[SR16420(BEF )04/95]
half page art:0011245-B
Checking the retractor
*
[SR16425(BEF )04/95]
9. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR16430(BEF )04/95]
To remove the retractor from automatic lock
mode, allow webbing to retract fully to its
stowed position and the retractor will
automatically switch back to the vehicle sensitive
locking mode for normal adult usage.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

48 [SR16440(BEF )04/95]Installing a Child Safety Seat at the Rear
Center Seating Position with Locking
Adjustable Lap Belt
[SR16450(BEF )04/95]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue up the webbing.
[SR16455(BEF )04/95]
2. Place the child safety seat in the center
seating position.
[SR16460(BEF )04/95]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
[SR16465(BEF )04/95]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
[SR16470(BEF )04/95]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
[SR16475(BEF )04/95]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

52
*
[SR16535(B )04/95]
5. Insert the belt tongue into the proper buckle
for that seating position until you hear a
snap and feel it latch. Make sure the tongue
is securely latched to the buckle by pulling
on the tongue. See Figure 3.
*
[SR16540(B )05/95]
half page art:0011365-A
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

54
*
[SR16555(B )04/95]
7. Grasp belt close to child seat and pull on the
shoulder belt portion of the combination
lap/shoulder belt, then allow the belt to
retract and remove all slack to securely
tighten the child safety seat in the vehicle.
See Figure 5.
*
[SR16560(B )05/95]
half page art:0011367-A
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

55
*
[SR16565(B )04/95]
8. Before placing the child into the child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to make sure that
the seat is held securely in place. See Figures
6 and 7. If the child seat moves excessively,
repeat steps 6 through 8, or properly install
the child seat in a different seating position.
[SR16570(B )05/95]
half page art:0011368-AFile:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

57
*
[SR18400(BEF )04/95]
Attaching Safety Seats With Tether Straps
*
[SR18410(BEF )03/01]
General Instructions
[SR18413(BEF )02/95]
Some manufacturers make safety seats that
include an upper tether strap that goes over the
seatback and attaches to an anchoring point.
Other manufacturers offer the tether strap as an
accessory. Contact the manufacturer of your
child safety seat for information about ordering
a tether strap.
*
[SR18417(B )12/91]
You can attach a tether strap anchor bracket to
the rear floor by using a tether anchor kit
(613D74), available at no charge from any Ford
dealership.
*
[SR18420(BEF )03/91]
Read and follow the instructions provided with
the kit carefully for installation of the child
tether strap anchor.
*
[SR18501(BEF )03/91]
Follow the child seat manufacturer's instructions
to attach the tether strap to the tether bracket.
*
[SR18700(B )04/95]
Ford recommends placement of tethered safety
seats in a rear seating position with the tether
strap installed to the tether anchoring point as
shown in the instructions provided with the
child tether strap anchor kit.
[SR18875(B )04/95]
This vehicle has provisions to install a tether
anchorage in the front, right hand and all second
row seating positions. It is easiest to install a
tether anchor at the second row, rear, center
seating position.
[SR18900(B )03/91]
If the tethered seat is installed in the front seat,
Ford recommends the center front seating
position, with the tether strap secured to the
center rear lap belt tongue or to the webbing of
the buckled center rear lap belt behind the child
safety seat. The front, right hand seating position
may be used if it is the only seating position
available.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

58
*
[SR18950(BEF )05/95]
RWARNING
Only use the tether attachment hole
locations shown in the illustrations. The
tether anchor may not perform properly if
the wrong mounting location is used.
*
[SR19400(B F )04/95]
The rear lap/shoulder safety belts should not be
used to secure the tether strap of a safety seat
located in the front seat.
*
[SR19500(BEF )05/95]
RWARNING
Failure to follow these precautions could
increase the chance of injury in an
accident.
*
[SR19550(B )05/95]
RWARNING
If the anchor bolt(s) is ever removed, the
hole(s) in the floor must be sealed to
prevent the possibility of exhaust fumes
entering the passenger compartment.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

80
*
[LG04675( ALL)05/95]
An example of a condition which corrects itself
occurs when an engine running out of fuel
begins to misfire. In this case, the Check Engine
Warning Light may turn on and will then set a
Diagnostic Trouble Code indicating that the
engine was misfiring while the last of the fuel
was being consumed. After refueling, the Check
Engine Warning Light will turn off after the
vehicle has completed three consecutive warm
up cycles without a misfire condition occurring.
A warm up cycle consists of engine start from a
cold condition (engine at ambient temperature)
and running until the engine reaches normal
operating temperature.
*
[LG04700( ALL)05/95]
On the fourth engine start up, the Check Engine
Warning Light will turn off as soon as the
engine begins to crank. It is not necessary to
have the engine serviced.
*
[LG04725( ALL)05/95]
Under certain conditions, the Check Engine
Warning Light may come on if the fuel cap is
not properly installed. If the Check Engine
Warning Light comes on and you suspect that
the fuel cap is not properly installed, pull off the
road as soon as it is safely possible and turn off
the engine. Remove and replace the fuel cap,
making sure it is properly seated.
*
[LG04750( ALL)05/95]
After completing the three consecutive warm up
cycles and on the fourth engine start up, the
Check Engine Warning Light should turn off. If
the light does not go off after the fourth engine
restart, have your vehicle serviced by your
dealer or a qualified technician.
File:ltlgb.ex
Update:Fri Jun 9 15:30:26 1995
ProCarManuals.com

119
Features
*
[FV00401(BEF )02/95]
Your vehicle has a variety of features designed
for your comfort, convenience and safety. Read
this chapter to find out about standard and
optional features.
*
[FV00601(BEF )01/95]
Doors
%*
[FV01801(BEF )03/95]
Anti-theft front door lock knobs
*
[FV01901(BEF )10/89]
Anti-theft lock knobs are designed to preclude
unlocking the door by pulling up on the bullet
type lock knob. To unlock and open the front
door from the inside of the vehicle, pull on the
inside door handle.
*
[FV06001(B F )05/90]
Tailgate
[FV06101(B )05/90]
To open the tailgate, first lower the tailgate
window.
[FV06201(B )05/90]
Next, lift the latch handle from the inside
tailgate panel of your vehicle, and lower the
tailgate.
[FV06300(B )05/90]
To close the tailgate, lift it and push forward
with enough force to latch the assembly securely
in position.
*
[FV06601(B F )05/90]
When open, the tailgate load should not exceed
500 lbs (227 kgs). If you want to load heavy
items onto your vehicle, Ford recommends that
you load them one at a time, directly on the bed
floor to avoid damage to the tailgate or its
supports.
File:ltfvb.ex
Update:Fri Jun 9 15:28:41 1995
ProCarManuals.com

128
*
[FV24101(BEF )01/95]
Seats
*
[FV24801(BEF )05/90]
Adjusting the Front Seat Manually
*
[FV24901(BEF )08/94]
To move the front seat forward or rearward:
*
[FV25001(BEF )08/94]
1. Find the adjustment lever at the lower left
corner of the front seat.
*
[FV25101(BEF )10/89]
2. Push the lever to the left to unlatch the seat.
*
[FV25201(BEF )04/95]
3. Move the seat to the desired position.
*
[FV25301(BEF )04/89]
4. Release the lever to latch the seat in its new
position. Make sure the seat locks securely in
place.
*
[FV25600(B F )03/91]
one third page art:0020218-B
Adjusting bucket seat
*
[FV25700(B F )05/95]
one third page art:0020220-E
Adjusting the bench seat
File:ltfvb.ex
Update:Fri Jun 9 15:28:41 1995
ProCarManuals.com