ignition FORD C MAX HYBRID 2013 2.G User Guide

Optional Settings
You can configure MyKey settings when you first create a MyKey.
You can also change the settings afterward with an admin key.
The following settings can be configured using an admin key:
•Set various vehicle speed limits. Warnings will be shown in the display
followed by an audible tone when your vehicle reaches the set speed.
You cannot override the set speed by fully depressing the accelerator
pedal.
•Set various vehicle speed reminders. Warnings will be shown in the
display followed by an audible tone when the set vehicle speed is
exceeded.
•Audio system maximum volume of 45%. A message will be shown
in the display when you attempt to exceed the limited volume.
Automatic volume control will be disabled.
•Always on setting. When this is selected, you will not be able to
disable Advance Trac, 911 Assist or the do not disturb feature
(if your vehicle is equipped).
CREATING A MYKEY
Use the information display to create a MyKey:
1. Insert the key you want to program into the ignition. If your vehicle
is equipped with a push-button start and you have a backup slot, put
the intelligent access key in the backup slot. If your vehicle does not
have a backup slot, hold your intelligent access key fob next to the
steering column. See theStarting and Stopping the Enginechapter
for the proper key fob placement.
2. Turn the ignition on.
3. From the main menu within the information display, pressOKor the
>button to navigate through the various screens. SelectSettings
and thenMyKey.
4. PressOKor the>button to selectCreate.
5. When prompted, hold theOKbutton until you see a message
informing you to label this key as a MyKey. The key will be restricted
at your vehicle’s next start.
After the key is successfully programmed, make sure you label it so you
can distinguish it from the admin keys.
You can also program optional settings for the key(s). Refer to
Programming/Changing Optional Settings.
MyKey67
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Programming/Changing Optional Settings
Note:All programmed keys can be cleared within the same key cycle in
which a key was programmed, otherwise an admin key is required to
clear the keys. To clear all keys, seeClearing all MyKeys.
You can access the optional settings through the information display
control.
1. Turn the ignition on using an admin key.
2. Access the main menu and select Settings, then MyKey.
3. Use the arrow buttons to get to an optional feature.
4. PressOKor>to scroll through settings.
5. PressOKor>to make a selection.
CLEARING ALL MYKEYS
You can clear the programming while you create a MyKey or use an
admin key to clear the restrictions. When you clear the restrictions, you
return the key to its original admin key status.
To clear your MyKey, use the information display to do the following:
1. Access the main menu and selectSettings, thenMyKey.
2. Scroll toClear Alland press theOKbutton.
3. Hold theOKbutton untilALL MYKEYS CLEAREDdisplays .
CHECKING MYKEY SYSTEM STATUS
The information display shows the programmed keys’ status:
•MYKEY DISTANCE:Tracks distance when drivers use a restricted
key. The only way to delete the accumulated distance is by using an
admin key to reset this to zero. If the MyKey distance does not
accumulate as expected, then:
1. The intended user is not using the programmed key.
2. An admin key user recently reset the distance.
•NUMBER OF MYKEY(S):Indicates the number of restricted keys
programmed to the vehicle. Use this feature to detect how many
restricted keys you have for your vehicle, or when a MyKey has
recently been deleted.
•NUMBER OF ADMIN KEY(S):Indicates how many admin keys are
programmed to the vehicle. Use this feature to determine how many
unrestricted keys you have for your vehicle, or if an additional MyKey
has been programmed.
68MyKey
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

USING MYKEY WITH REMOTE START SYSTEMS
MyKey is not compatible with non-Ford-approved (unlicensed)
aftermarket remote start systems. If you choose to install a remote start
system, please see your Ford authorized dealer for a Ford-approved
remote start system.
The following information may help customers who choose to install an
unlicensed remote start system. The instructions provided below do not
make the MyKey system or its features compatible with any unlicensed
remote start system, but they may help you retain some MyKey
functions.
Vehicles Equipped with Traditional Keys
MyKey programming and restrictions are not compatible with unlicensed
remote start systems, but there are ways you can retain some of the
MyKey functions. To learn if this is possible, use the remote start to start
your vehicle. While the vehicle’s engine is running: .
1. Insert your key into the ignition cylinder.
2. Restart the engine using the key in the ignition.
3. If MyKey recognizes your unlicensed remote start system as an
additional admin key with its associated privileges, then you can
program it as a MyKey just as you would program a traditional key.
To program an unlicensed remote start system as a MyKey, do the
following:
•Enter the vehicle and close all doors.
•Use the remote start to start your vehicle.
•See theCreating a MyKeysection and follow Steps 1–5.
Vehicles Equipped with Intelligent Access Key (Push-button Start)
It is not possible to program your unlicensed remote start system
as a MyKey if your vehicle is equipped with intelligent access keys
(push-button start), but you can still retain the MyKey programming
with your intelligent access key fob by following this process:
1. Enter the vehicle and close all doors.
2. Start your vehicle with the remote start. Do not open a door or shift
the vehicle out of P (Park) as either action will cause the engine to
stall. While the engine is running, your remote start retains its admin
key status.
3. Restart the engine by pressing the Start/Stop button. SeeKeyless
Startingfor more information. The vehicle will identify your
intelligent access fob as an admin key or a MyKey, depending
on the settings of the actual key used to start the vehicle.
MyKey69
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Smart Unlocks for Integrated Keyhead Transmitter
This feature helps to prevent you from locking yourself out of your
vehicle if your key is still in the ignition.
When you open one of the front doors and lock your vehicle with the
power door lock control, all the doors will lock then unlock if your key is
still in the ignition.
You can still lock your vehicle by pressing the lock button on the
transmitter even if the doors are not closed.
If both front doors are closed, you can lock your vehicle by any method,
regardless of whether the key is in the ignition or not.
Smart Unlocks for Intelligent Access Keys (If Equipped)
This feature helps to prevent you from unintentionally locking your
intelligent access key inside your vehicle’s passenger compartment or
rear cargo area.
When you lock your vehicle using the power door lock control (with the
door open, transmissionPand ignition off), after you close the door
your vehicle will search for an intelligent access key in the passenger
compartment. If your vehicle finds a key, all of the doors will immediately
unlock and the horn will sound, indicating that the intelligent access key is
inside.
You can override the smart unlock feature and intentionally lock the
intelligent access key inside your vehicle. To do this, either:
•close all the doors and then press the lock button on another
intelligent access key, or
•touch the locking area on the handle with another intelligent access
key in your hand.
When you open one of the front doors and lock your vehicle using the
power door lock control, all doors will lock then unlock if:
•the ignition is on, or
•the ignition is off and the vehicle is not inP.
Locks75
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Autolock and Unlock (If Equipped)
The autolock feature will lock all the doors when:
•all doors are closed
•the ignition is on
•you shift into any gear putting the vehicle in motion, and
•the vehicle attains a speed greater than 4 mph (7 km/h).
The autounlock feature will unlock all the doors when:
•autolock has locked the doors
•you stop the vehicle and switch the ignition off or to accessory mode,
and
•the driver’s door is opened within 10 minutes.
Note:The doors will not autounlock if you have electronically locked
them before opening the driver’s door.
Enabling or Disabling Autolock and Autounlock
Note:Your authorized dealer can perform this procedure, or you can do
the procedure yourself.
To enable or disable these features, do the following:
Note:You will have 30 seconds to complete the procedure.
1. Switch the ignition on.
2. Press the power door unlock button three times.
3. Switch the ignition off.
4. Press the power door unlock button three times.
5. Switch the ignition on. The horn will chirp indicating the programming
mode has been entered.
Autolock:Press the power door unlock control, then the lock control.
The horn will chirp once if autolock was disabled or twice (one short and
one long chirp) if autolock was enabled.
Autounlock:Press the power door lock control, then the unlock control.
The horn will chirp once if autounlock was disabled or twice (one short
and one long chirp) if autounlock was enabled.
6. Switch the ignition off. The horn will chirp once to confirm the
procedure is complete.
Note:The autounlock feature can be enabled or disabled independently
of the autolock feature.
76Locks
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Illuminated Entry
The interior lamps and select exterior lamps illuminate when you unlock
the doors with the remote entry system.
The illuminated entry system turns off the lights if:
•the ignition is on,
•you press the remote transmitter lock button, or
•after 25 seconds of illumination.
The lights will not turn off if:
•you turn them on with the lamp control, or
•any door is open.
Illuminated Exit
The interior lamps and select exterior lamps illuminate when all doors
are closed and you switch the ignition off and remove the key from the
ignition (integrated keyhead transmitter only).
The lamps turn off if all the doors remain closed and:
•25 seconds elapse
•
you insert the key in the ignition (integrated keyhead transmitter only)
•you press theSTART/STOPbutton (intelligent access key only).
Battery Saver
If you leave the courtesy lamps, dome lamps or headlamps on and switch
the ignition off, the battery saver shuts them off after some time.
Accessory Mode Battery Saver for Intelligent Access Keys
(If Equipped)
If you leave the ignition on after leaving your vehicle, it will shut off
15 minutes after you close all of the doors.
Locks77
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Power Liftgate (If Equipped)
WARNING:Make sure all persons are clear of the power liftgate
area before using the power liftgate control.
WARNING:Keep keys out of reach of children. Do not allow
children to play near an open or moving power liftgate.
Note:Cycling the ignition while the liftgate is power closing and is near
the latch may cause the liftgate to stop operation. Make sure that the
liftgate is closed before operating or moving the vehicle, especially in
an enclosure, like a garage or a parking structure. The liftgate or its
components could be damaged.
Opening and Closing the Power Liftgate
Note:The doors must be unlocked to operate the power liftgate.
Note:The liftgate movement direction can be stopped with a second
press of the instrument panel, or the control button on the liftgate, a
second double press of the transmitter button, or by using a kicking
motion with your foot for hands-free liftgates.
If the engine is running, the liftgate will only operate with the vehicle inP.
A chime sequence will sound as the liftgate begins to power close.
Another chime sequence indicates a problem with the close request,
caused by:
•the ignition is on and the transmission is not inP,or
•the battery voltage is below the minimum operating voltage, or
•the vehicle speed is at or above 3 mph (5 km/h).
If the liftgate reverses and starts to close after an open request, four
short warning chimes indicate excessive load on the gate or a possible
strut failure. See your authorized dealer if you still have a fast chime
after the load is removed.
To open or close from the instrument panel:Press the
instrument panel button.
Note:The doors must be unlocked.
To open or close with the remote control:Press the remote
control button twice within three seconds.
Locks79
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

SECURILOCK® PASSIVE ANTI-THEFT SYSTEM
Note:The system is not compatible with non-Ford aftermarket remote
start systems. Use of these systems may result in vehicle starting
problems and a loss of security protection.
Note:
Metallic objects, electronic devices or a second coded key on the
same key chain may cause vehicle starting issues if they are too close to
the key when starting the engine. Prevent these objects from touching the
coded key while starting the engine. Switch the ignition off, move all
objects on the key chain away from the coded key and restart the engine if
a problem occurs.
Note:Do not leave a duplicate coded key in the vehicle. Always take
your keys and lock all doors when leaving the vehicle.
The system is an engine immobilization system. It helps prevent the
engine from starting unless a coded key programmed to your vehicle
is used. Using the wrong key may prevent the engine from starting.
A message may appear in the information display.
If you are unable to start the engine with a correctly coded key, a malfunction
has happened and a message may appear in the information display.
Automatic Arming
Your vehicle arms immediately after you switch the ignition off.
Automatic Disarming
Your vehicle disarms when you switch the ignition on with a coded key.
Replacement Keys
Note:Your vehicle comes with two integrated keyhead transmitters or
two intelligent access keys.
The integrated keyhead transmitter functions as a programmed ignition key
that operates all the locks and starts the vehicle, as well as a remote control.
The intelligent access key functions as a programmed key that operates
the driver door lock and activates the intelligent access with push button
start systems, as well as a remote control.
If your programmed transmitters or standard SecuriLock coded keys
(integrated keyhead transmitters only) are lost or stolen and you do not
have an extra coded key, you will need to have your vehicle towed to an
authorized dealer. The key codes need to be erased from your vehicle
and new coded keys will need to be programmed.
Store an extra programmed key away from the vehicle in a safe place to
help prevent any inconveniences. See an authorized dealer to purchase
additional spare or replacement keys.
Security83
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Programming a Spare Integrated Keyhead Transmitter
Note:A maximum of eight coded keys can be programmed to your
vehicle; all eight can be integrated keyhead transmitters.
You can program your own integrated keyhead transmitter or standard
SecuriLock® coded keys to your vehicle. This procedure will program
both the engine immobilizer keycode and the remote entry portion of the
remote control to your vehicle.
Only use integrated keyhead transmitters or standard SecuriLock® keys.
You must have two previously programmed coded keys and the new
unprogrammed key readily accessible. See your authorized dealer to have
the spare key programmed if two previously programmed coded keys are
not available.
Read and understand the entire procedure before you begin.
1. Insert the first previously programmed coded key into the ignition.
2. Turn the ignition from off to on. Keep the ignition on for at least three
seconds, but no more than 10 seconds.
3. Turn the ignition off and remove the first coded key from the ignition.
4. After three seconds but within 10 seconds of turning the ignition off,
insert the second previously coded key into the ignition.
5. Turn the ignition from off to on. Keep the ignition on for at least
three seconds, but no more than 10 seconds.
6. Turn the ignition off and remove the second previously programmed
coded key from the ignition.
7. After three seconds but within 10 seconds of turning the ignition off
and removing the previously programmed coded key, insert the new
unprogrammed key into the ignition.
8. Turn the ignition from off to on. Keep the ignition on for at least
six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the engine
and operate the remote entry system (if the new key is an integrated
keyhead transmitter).
If it was not programmed successfully, wait 10 seconds and repeat
Steps 1 through 8. If you are still unsuccessful, bring your vehicle to
your authorized dealer.
Wait 20 seconds and then repeat this procedure from Step 1 to program
an additional key.
84Security
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)

Programming a Spare Intelligent Access Key
See your authorized dealer to have additional keys programmed to your
vehicle.
ANTI-THEFT ALARM (IF EQUIPPED)
The system will warn you of an unauthorized entry to your vehicle.
The park and turn lamps flash and the horn sounds if unauthorized entry
is attempted while the alarm is armed. It triggers immediately if the
luggage compartment or the hood opens, and after a 12-second delay if
any door opens.
Take all remote controls to an authorized dealer if there is any potential
alarm problem with your vehicle.
Arming the Alarm
The alarm is ready to arm when there is not a key in the ignition. Press
the door lock button and close the door to arm the alarm.
Disarming the alarm
Disarm the alarm by any of the following actions:
•Unlock the doors or luggage compartment with the remote control.
•Turn the ignition on or start the vehicle.
•Use a key in the driver door to unlock your vehicle, then turn the
ignition on within 12 seconds.
Security85
2013 C-Max Full Hybrid(34h)
Owners Guide gf, 3rd Printing, January 2013
USA(fus)