service FORD ESCAPE HYBRID 2007 2.G Quick Reference Guide

Fuel Tank Capacity:Your vehicle is
equipped with a 15gallon (56.8L)
fuel tank.
Octane Recommendations:Your vehicle isdesigned to use “Regular” unleadedgasolinewith a pump octane rating of 87 for
optimum performance. Using gasoline with
lower octane ratings may
decrease performance.
Tire Pressure:Your
tire pressure is
properly set at the
dealership according
to the recommended specifications found
on the Certification Label located on the
driver’s side front door latch pillar, the
trailing edge of the driver’sdoor or the
edge of the driver’sdoor.Tire pressure
information can also be
found on the Tire
Information Label on the driver’s side front
door latch pillar or edge of driver’s door.
Please check your tirepressure during
routine maintenance and seasonal
changes.
WARNING:Improperly inflated
tires can affect vehicle handling and can
fail suddenly, resulting in a possible loss of
vehicle control.Unique Service Intervals:
Please check
your Owner’s Guide for proper service
intervals. Your vehicle is equipped with a
rear air filter that must be inspected or
replaced at every service interval to avoid
damage to the hybrid system. Special
caution is required when servicing brake
pads.
Please refer to the Owner’s Guideand/or Service Manual for information on
servicing brake pads.
Fuel Pump / High Voltage
Shutoff Switches:The fuel
pump shutoff switch is
located in the front
passenger’s footwell behind the
flipup cover. The high voltage shutoff
switch is located in the rear passenger
side of the vehicle, in the jack
compartment behind the jack access
door. These switches provide added
protection by discontinuing fuel to the
engine and by shutting offpower to the
high voltage battery in case of
an accident.
2007 FORD Escape Hybrid
*F7M6J19G217AA*
Ford Motor CompanyCustomer Relationship Center
P.O. Box 6248
Dearborn, MI 48121
18003923673 (FORD)
(TDD for the hearing impaired: 18002325952)
7M6J19G217AA
February 2006
First Printing
Quick Reference Guide
This Quick Reference Guide is not intended to replace your vehicle Owner’s Guide which contains more detailed information concerning the features of
your vehicle, as well as important safety warnings designed to help reduce the risk of injury to you and your passengers. Please read your entire Owner’s
Guide carefully as you begin learning about your new vehicle and refer to the appropriate sections when questions arise.
All information contained in this Quick Reference Guide was accurate at the time of duplication. We reserve the right to change features, operation
and/or functionality of any vehicle specification at any time. Your Ford dealer is the best source for the most current information.
For detailed operating and safety information, please consult your Owner’s Guide.
MANUAL HEATING & AIR CONDITIONING SYSTEM
1Fan Speed Control:Rotate the knob to
adjust the speed of air that is circulated
in the vehicle.
2 Max A/C:With the climate system set to
MAX A/C, the engine will run continuously,
reducing fuel economy.
3Recirculated Air:Recirculated air flows
from the instrument panel vents to cool
the vehicle.
4A/C:Outside air flows from the
instrument panel vents to cool the vehicle.
When A/C mode is selected, you may
notice the air temperature cycle from
cooler to warmer as the gas engine turns
on and off. When in electric mode, the
fan will still blow air in the cabin, but no
heat will be removed by the air conditioner.
5Panel:Distributes outside air through
the instrument panel vents only.
6Off:Outside air is shut out and the
climate control system is turned off.
7Panel and Floor:Distributes outside air
through the instrument panel vents and
floor vents.
8Floor:Distributes outside air through the
floor vents only.
9Floor and Defrost:Distributes outside air
through the windshield defroster vents
and the floor vents. This featurewill cause
the gas engine
to run continuously, reducing
fuel economy.
10Defrost:Distributes outside air through
the windshield defroster vents. With the
climate system set to defrost mode, the
engine will run continuously, reducing
fuel economy.
11Temperature Control:Rotate the knob to
adjust the temperature of the airflow
inside the vehicle.
1
234
6
79
11
5
810
HYBRID ENERGY FLOW WITH AUDIOPHILE AND NAVIGATION
(if equipped)
1AM/FM:Pressing AM/FM in navigation mode
will return the system to the audio screen.
2 Fuel Economy Function:Press to view average
and instantaneous fuel economy screen.
3Seek:Use to find the next/previous listenable
radio station or to advance tracks, if in
CD mode.
4HOME:Press and hold the HOME key to
storecurrent vehicle location as home.
Pressing HOME after the home location has
been set will calculate a route to return to that
set home location when in navigation mode.
5 Energy Flow Function:Press for status of
engine and battery. To disengage, press the
control again. Your energy flow screen displays
how power is used and transferred between
the electric motor, the high voltage battery,
and the gasoline engine. It also indicates
which mode you arecurrently operating in.
Please see your Owner’s Guide for
more information.
6Current Location:Press for information on
current location.
7Memory Presets:Stores favorite AM/FM
stations and allows CD access when in CD
mode. To store, press and hold until
PRESET SAVED appears in display.
8Navigation:Press NAV to access the navigation
system menu. Make sure the vehicle is in Park
(P) before you enter a destination and the
navigation CD is loaded into the radio head.
9MAP:The control works in all modes. Press
MAP to show current location.
10 Back:Works only in navigation mode. Press
to return to the previous screen.
11 ENTER:Use ENTER to view a menu in the
navigation system. Press the control up, down,
left, or right to highlight an item in the
display. Press the center of the control to
make selection.
NOTE:With this system, the Six CD Changer is
located under the passenger seat. To use the
navigation system and listen to an audio CD,
the navigation CD must be loaded into the
radio head and the audio CD must be loaded
into the changer.
Smudges, fingerprints or scratches on the navigation disks could effect performance of the navigation system.
Keep disks clean and stored in the protective jackets when not in use.
1Band:Press to select AM, FM1 or FM2
frequency bands.
2CD:Press to enter CD mode. If a CD is
already loaded into the system, the CD
play will begin where it last ended.
3Load:Press to open the CD door, thenload the CD into the player. Press LOAD
and then a preset number to select a slot.
Press and hold LOAD to activate autoload.
4Scan Function:In radio mode, press to
hear a sampling of all listenable stations.
In CD mode, press to hear a brief sampling
of all selections on the current CD.
5Volume/Power Control:Push the control
to turnthe audio system on or off. Turnthe
control to raise or lower volume.
6Disc/Tune CAT:In radio mode, press to
move to the next frequency up or down
the band. In CD mode, press to select a
disc in the CD player.CAT is only available
when equipped with satellite radio. The kit
to enable satellite reception is availablethrough your Ford dealer. Detailed satellite
instructions are included with the dealer
installed kit.
7Memory Presets:Select AM, FM1, or
FM2 band, then tune to a station. Next,
press and hold a control until the
sound returns.
8Aux:This function is not operational.
9Setting the Clock:Press MENU until
SELECT HOUR or SELECT MINS is
displayed. Press SEL and the up/down
arrows to set the time. Press MENU again
to disengage the clock mode.
Speed Sensitive Volume:This audio systemmay have speed sensitive volume control.For moreinformation on its features and
functions, please consult your Owner’s
Guide.
1
3
5
7
8
10
2
6
4
9
11
AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREO INDASH SIX CD/MP3 RADIO
(if equipped)
1
34
5
6
7
9
8
2
Essential Information >

1Fog Lamp Control:Press the control to
activate the fog lamps during headlamp
operation. Press the control again to deactivate
the fog lamps. The fog lamps will not operate
when the high beams are activated.
2Power Side View Mirrors:Rotate clockwise to
adjust the right mirror or counterclockwise to
adjust the left mirror. Then, move the control in
the direction you wish to tilt the mirror. Return
the control to the center position to lock the
mirror in place. To adjust the power side view
mirrors, ignition must be in the RUN position.
3Speed Control:To operate, the speed control
must be ON and the vehicle’s speed must be
over 30 mph (48 km/h). To set a speed, press
SET ACC. Toset a higher speed, press SET
ACC again. To set a lower speed, press CST.
Pressing RSM will return to the previously set
speed. To disengage the speed control, press the
CAN button or depress the brake pedal. To turn
off the speed control, press the OFF button.
4 ABS Warning Lamp:Illuminates briefly when ignition is turned
to the RUN position. If the light remains
on for morethan a few seconds, an ABS
fault is indicated. Normal braking is still
functional unless the brake warning light
is also illuminated.
5 Battery Gauge:The battery gauge provides
information about your vehicle’s energy usage.
When the pointer is directed at ASSIST, this
means the batteryis providing extra power to
boost the vehicle’s acceleration. When it’s
pointing to CHARGE, extra energy is being
stored in the battery while idling, coasting or
slowing down. When you press the brake pedal,
the pointer swings counterclockwise into the
CHARGEzone to report that regenerative
braking is underway. If the needle does not
move when braking, the battery is fully charged.
6 Tire Pressure Monitoring System (TPMS): Using radiofrequency pressure sensors, this
system monitors tire pressure on all road tires
and provides the driver with a warning light
when air needs to be added. Please see your
Owner’s Guide for additional information.
7 Tachometer:Engine RPMs are indicated by
the tachometer. When the vehicle operates
in pure electric mode, the tachometer
pointer drops
below the zero mark where it
points at a special symbol labeled EV for
electric vehicle. Driving with your tachometer
pointer continuously at the top of the scale
may damage the engine.
8Message Center:When the ignition is in the
RUN position, the message center in your
vehicle’sinstrument cluster will display
information on your vehicle’s operating
functions, as well as warning messages. There
are two selectable features, located on the
center console, for your message
center: SET
and INFO. SET is used to select and reset
various functions shown in the INFO menu.
INFO displays a menu which consists of
average fuel economy (if equipped), distance to
empty,instantaneous fuel economy
(if equipped), high voltage battery status, units
(english/metric), language, system check and
INFOdisplay on/off.
9 Tilt Steering Wheel Lever:Push the tilt
steering wheel lever downward to unlock the
steering wheel. Then move the steering
wheel up or down. Pull the lever
up into the
original position to lock the steeringwheel.
Never adjust the steering wheel while the
vehicle is moving.
10 Ready Indicator:Illuminates after the vehicle has successfully
started. The vehicle is ready to drive even if
you don't hear the engine running.
11 Service Soon:Illuminates when the vehicle has detected
amalfunction. Report the fault to your
Hybrid certified dealer at the earliest
opportunity.
12 Master Vehicle Electrical Hazard Warning Lamp:Indicates a major hybrid component failure
or other major vehicle failure that will cause
the vehicle to shut down or fail to start.
Please see your Owner’s Guide for
additional information.
13 Service Engine Soon Lamp:Illuminates briefly when ignition is turned to
the RUN position. Solid illumination after
start indicates the on board diagnostics
system has detected a malfunction. Have
your
vehicle serviced immediately at a Hybrid
certified dealer.
14 Front and Rear Wiper / Washer Control:
Front:Move the control down one position for
intermittent operation. Rotate the speed control
up for fast intervals and down for slow intervals.
Move the control down two positions from OFF
for normal or lowspeed wiper operation. Move
the control down three positions from OFF for
highspeed wiper operation. Pull the control
towardyou to activate the windshield washer.
Release the control to stop washer fluid spray.
Move the control up and release for one wipe
with mist.
Rear:Rotate the end of the control
upward to the position for intermittent
operation. Adjust the speed control for fast or
slow intervals. Rotate the control upward to ON
for normalspeed operation. Rotate the control
down to the position and release to activate
the rear washer.
15 Auxiliary Power Point (12V):The 12V
power point outlet, located to the left of
the 110 VAC outlet (if equipped), is
designed for accessory plugs only. Do not
insert any other object; damage may occur
and blow the fuse. This power outlet will
require an adapter in order to plug in an
electric device.
16 Rear Window Defroster Control:Push to
clear the rear window of thin ice and frost.
The rear window defroster turns off
automatically after 15 minutes or when the
ignition is turned off. To manually turn off
the defroster, push the control.
17 Power Point 110 VAC (if equipped):Thisoutlet, located on the floor console in front of
the gearshift, is used for powering electrical
devices that require up to 150W. Exceeding
this limit will cause the power point to cut off
the power temporarily to provide overload
protection. The green indicator light will
illuminate when the power point is ready to
supply power, will blink when it is in fault
mode, and will turn off when the power
supply is off(ignition is not in the RUN
position). This outlet does not require an
adapter in order to plug in an electrical
device.
18 Passenger Airbag Off: The passenger
airbag off indicator, located just below the
radio, will illuminate when the passenger’s
frontal airbag is off. Please see your Owner’s
Guide for additional information.
Unique Hybrid Operating Characteristics
Battery:The Ford Escape Hybrid is equipped
with a high voltage battery temperature
management system in the rear of the
vehicle. This system cools the battery in order
to ensure battery life and optimize high
voltage battery performance. You may hear a
slight tap sound as the vent door operates. In
addition, you may hear a fan noise in the rear
of the vehicle. This is the temperature
management fan. These noises are a
customary part of hybrid operation and do not
require service. The hybrid high voltage
battery may go through a self–reconditioning
process from timetotime, to optimize high
voltage battery performance.
You may notice
slight changes in drivability during thereconditioning process. This is an important part
of the Escape Hybrid's high voltage battery
optimizing features.
Engine:The engine speed in a hybrid is not
directly tied to the vehicle speed. Under
certain conditions the engine speed, as
indicated on the tachometer while driving,
may appear much higher than that of a
conventional automobile. This is caused by
engine speed optimization to maximize fuel
economy.In prolonged mountainous driving,
you may also see the engine tachometer
slowly moving up and down. This is done to
maintain the battery. You may also hear a
slight whine or whistle when operating your
vehicle. This is the normal operation of the
electric generator in the hybrid system.
If your 12V battery should become
disconnected, you may experience engine
spin for 35 seconds after the key is turned
to the LOCK position, for the next key cycle
only. The computer is relearning the start up
characteristics of your vehicle.
Driving to Optimize Fuel Economy
As with any vehicle, fuel economy can be
significantly impacted by your driving habits
and accessory usage. To maximize fuel
economy, try to extend the length of
time you run in electric mode by lightly
accelerating the vehicle. The longer you keep
the engine from starting, the better the fuel
economy you will achieve.
Please be aware of the following
vehicle functions which reduce fuel
economy performance:
TireInflation:Keep tires properly inflated and
use only recommended size.
Climate Control:With the climate control system
set to MAX A/C, defrost and defrost/floor mode
(the orange graphics on your climate control),
the gas engine will run continuously, reducing
fuel economy.The A/C mode is more
fuelefficient than the MAX A/C mode.
Driver Habits:Rapid starts (jackrabbit starts),
towing, and heavy loads all impact the
amount of energy required to move the
vehicle. In general, better fuel economy is
achieved during moderate acceleration and
deceleration, as opposed to aggressive
acceleration and deceleration. This is true
regardless of the mode in which you're operating.
Do not carry extra loadsDo not decrease aerodynamicsUse speed controlObserve posted speed limitsKeep engine tuned
Normal Vehicle OperationStarting:Turn the ignition key to the START
position while the vehicle is in Park (P). The gas
engine will turn on, but may shut off shortly after
starting, depending on temperature and battery
state of charge. This is a natural part of the
Escape Hybrid's fuelsaving features. You do not
need to restart the vehicle.
NOTE:If the vehicle is
left inoperative for over 31 days — it may (but
probably won’t) be necessary to jumpstart the
vehicle. Your Escape Hybrid is equipped with a
high voltage battery jumpstart feature in addition
to the traditional 12V system. Consult your
Owner’s Guide for jumpstart instructions.
Driving:The gas engine automatically starts
and stops to provide power when it's needed
and to save fuel when it's not. While coasting
at low speeds, idling, or coming to a stop,
the gas engine typically shuts down to
conserve fuel and the vehicle operates in
electriconly mode. The gas engine will kick
in upon acceleration. Conditions that cause
the engine to start up include:
High voltage battery recharge required
Driver acceleration demands
additional power
Overly hot or cold outside temperature,
or if the batteryis overly hot or cold, the
engine may engage sooner than usual
Ascending a hill, accelerating quickly,
or when driving conditions require
additional power
The gasoline engine will not shut offif
the climate control is set to MAX A/C,
defrost mode or defrost / floor mode
Stopping:The gas engine may shut off as you
come to a stop to conserve fuel. Restarting
the vehicle is not required. Simply step on
the accelerator when you are ready to drive.
Transmission Operation:Due to the
technologically advanced, electronically
controlled Continuously Variable Transaxle
(eCVT) you will not feel shift changes like
those of a traditional vehicle. The Escape
Hybrid's transmission is designed to do
its work seamlessly.
Neutral:It is not recommended to idle the
vehicle in (N) Neutral for extended periods
of time because this will discharge your high
voltage battery and decrease fuel economy.
Low Gear:Slowing down in (L) Low gear may
cause a sensation of engine braking during
deceleration. Response during acceleration
should be the same as in (D) Drive position.
Reverse:(R) Reverse gear vehicle speed is
limited to 22 mph (35 km/h) until shifted to
a nonreverse gear.In most cases, the vehicle
will operate in electriconly mode while
in (R) Reverse.
Hybrid Operation >The Ford Escape Hybrid is a whole new kind of SUV that combines electric and gasoline propulsion
without compromise, to provide breakthrough performance and efficiency. It requires no special fuels and never has to be plugged in.
Familiarizing yourself with these unique characteristics will help ensure optimal performance from your new vehicle. Instrument Panel Features >
INSTRUMENT PANEL
12
12
16
11
6
43
5
879
10
13314 15
17
18
THE FORD ESCAPE HYBRIDis 100% SUV and
100% Hybrid. It requires no special fuels and never
has to be plugged in. All you have to do is get in
and drive.
With all the confidence of an authentic Ford SUV
combined with the benefits of a full hybrid system,
every Ford Escape Hybrid is equipped to help you go
anywhere and do anything — now more efficiently than
ever and in an environmentally conscious manner.
In order to help you fully appreciate the
features of your new vehicle and its unique
characteristics, we invite you to explore this
easytouse Quick Reference Guide.
This vehicle has unique driving characteristics to
maximize its hybrid operation. Drive with care and wear asafety belt at all times. Ford urges you to read the
Owner’s Guide and the Driving Your SUV or Truck
Supplement for further information on safe driving
precautions and instructions.