headlamp FORD ESCORT 1999 6.G User Guide

Downloaded from www.Manualslib.com manuals search engine ²Next, at least 20 minutes driving in stop-and-go, city-type traffic with
at least four idle periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete.
EXTERIOR BULBS
Replacing exterior bulbs
It is a good idea to check the operation of the following lights frequently:
²Headlamps
²Turn signals
²Foglamps (if equipped)
²High-mount brakelamp
²Tail lamps
²Brakelamps
²Backup lamps
²License plate lamp
²Hazard flashers
Do not remove lamp bulbs unless they will be replaced immediately. If a
bulb is removed for an extended period of time, contaminants may enter
the lamp housings and affect performance.
Handle a halogen bulb carefully and keep out of children's reach.
Grasp the bulb only by its plastic base and do not touch the
glass; the oil from your hand could cause the bulb to break the next
time that the headlamps are operated.
Maintenance and care
161

Downloaded from www.Manualslib.com manuals search engine Replacing headlamp bulbs
1. Make sure that the headlamps are turned OFF.
²Coupe
²Sedan/wagon
2. Open the hood and disconnect the headlamp wiring socket from the
in-line connector. This will make it easier to change the bulb.
3. Remove the protective dust shield
from the housing by turning the
dust shield counterclockwise (when
viewed from the rear).
4. Release clip and disconnect the electrical connector from the bulb.
Maintenance and care
162

Downloaded from www.Manualslib.com manuals search engine 5. Remove the bulb retaining ring by
rotating it counterclockwise.
6. Without turning, remove the old
bulb from the lamp assembly by
pulling it straight back out of the
lamp assembly and replace.
7. Install the new bulb in lamp assembly by pushing straight in with the
bulb's plastic base facing upward. Turn the bulb slightly to align the
grooves in the plastic base with the tabs in the lamp assembly.
8. Install the bulb retaining ring over the plastic base and lock the ring
by rotating it clockwise until it snaps into place.
9. Connect the electrical connector into the plastic base until it ªsnapsº.
10. Install the protective dust shield and lock the shield by rotating it
clockwise until it locks into position.
11. Connect the headlamp wiring socket to the in-line connector.
12. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.
Maintenance and care
163

Downloaded from www.Manualslib.com manuals search engine INTERIOR BULBS
Dome lamp
1. Remove the lamp lens by applying
pressure to both tabs at the top of
the lamp and pulling lens
downward.
2. Pull out the burned-out bulb and
install a new one.
3. Install the lamp lens by applying
pressure to both sides of the lamp
lens and popping the lamp lens up
on the assembly.
Map lamps
For bulb replacement, see a qualified service technician or your dealer.
Using the right bulbs
Function Trade Number
Front park/turn lamps 3457 NAK
Foglamps (if equipped) 881
Headlamps-aero high and low beam 9007
Rear license plate lamps 168
High-mount brake lamp 921
Backup lamps 3156K
Brake lamps 3157K
Interior overhead lamp 12V/10W
To replace all instrument panel lights - see your dealer
OFF DOOR ON
Maintenance and care
167

Downloaded from www.Manualslib.com manuals search engine AIMING THE HEADLAMPS
Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD)
on each headlamp. Each headlamp may be properly aimed in the vertical
(up/down) and the horizontal (left/right) directions using your VHAD
system. The headlamps on your vehicle are properly aimed at the
assembly plant.
A bubble (vertical indicator) that is not centered between the two red
lines does not necessarily indicate out-of-aim headlamps. If your vehicle
is not positioned on a level surface, the slope will be included in the
vertical indication. Therefore, vertical and horizontal headlamp
adjustment should be performed only when the beam direction appears
to be incorrect.
You will need one 4 mm wrench or socket to make the adjustments.
If the vehicle has been in an accident, the vehicle's front structure
should be properly aligned before aiming the headlamps.
Horizontal aim adjustment
1. Park the vehicle on a level
surface.
2. With the hood open, locate the
horizontal indicator and the
adjusting screw. They are located
below the viewing window at the
rear of the headlamp assembly.
3. The ªLº and ªRº under the viewing window on the top of the
headlamp refer to the directional change (left or right) of the horizontal
aim.
4.Usea4mmwrench or socket to turn the horizontal adjusting screw
until the forward edge of the knurled portion of the screw is aligned with
the ª0º reference mark (as shown) on the plastic slider when viewed
directly from above.
Maintenance and care
168

Downloaded from www.Manualslib.com manuals search engine Vertical aim adjustment
1. Park the vehicle on a level
surface.
2. With the hood open, locate the
bubble level and the vertical
adjustment screw. The adjustment
screw is located on the outboard
side of the headlamp below the
headlamp upper attachment.
3. The ªUPº and ªDNº on the bubble
indicate the directional change (up
or down) of the vertical aim.
4.Usea4mmwrench or socket to
turn the vertical adjusting screw
clockwise or counterclockwise until
the bubble is centered between the
lines.
Repeat the above process to the other headlamp, if necessary.
CLEANING AND CARING FOR YOUR VEHICLE
Refer to the Customer Assistance chapter for a list of Ford-approved
cleaners, polishes and waxes.
L
R
UP
DN
DNUP
Maintenance and care
169

Downloaded from www.Manualslib.com manuals search engine Headlamps ...................................42
aiming ...............................168,169
bulb specifications ..................167
daytime running lights .............43
flash to pass ..............................43
high beam ..............................9,43
replacing bulbs .......................162
turning on and off ....................42
warning chime ..........................10
Heating ........................................37
heater only system ...................37
heating and air
conditioning system .................39
Hood ..........................................127
Ignition ................................176,177
positions of the ignition ...........42
Infant seats
(see Safety seats) .......................77
Inspection/
maintenance (I/M) testing .......160
Instrument panel ..........................6
cleaning ...................................172
lighting up panel
and interior ...............................14
location of components ..............6
Jump-starting your vehicle ......117
Keys
key in ignition chime ...............10
positions of the ignition ...........42
Lamps
cargo lamps ...............................14
daytime running light ...............43
fog lamps ...................................44
headlamps ..........................42,162
headlamps, flash to pass ..........43
instrument panel, dimming .....14
interior lamps ....................51,167
replacing bulbs ..161,164,165,166
Lane change indicator
(see Turn signal) ........................43
Lights, warning and indicator ......6
air bag ..........................................8anti-lock brakes (ABS) .........9,89
anti-theft .....................................9
brake ............................................8
charging system ........................10
high beam ...................................9
liftgate ajar ................................10
low fuel ........................................7
oil pressure ...............................10
safety belt ...................................8
service engine soon ....................7
turn signal indicator ...................9
Load limits .................................100
GAWR ......................................100
GVWR ......................................100
trailer towing ..........................100
Locks
childproof ..................................52
Lubricant specifications ....175,176
Manual transaxle .........................92
fluid capacities ........................174
lubricant specifications ..........176
reverse .......................................95
Mirrors
side view mirrors (power) .......14
Moon roof ....................................50
Motorcraft parts .................156,174
Octane rating ............................155
Odometer .....................................13
Panic alarm feature, remote
entry system ................................57
Parking brake ..............................90
Parts (see Motorcraft parts) ....174
Power distribution box
(see Fuses) ...............................110
Power door locks ........................52
Power steering ............................91
fluid, checking and adding ....140
fluid, refill capacity ................174
fluid, specifications ..........175,176
Radio ............................................15
Relays .................................107,113
Remote entry system ............55,57
Index
196