timing belt FORD FIESTA 2007 Owner's Manual

Engine - 1.25L Dura
303-01 A-41 Duratec-I 6V (Sigma)ll.~
:eel 6V (Sigma)llI4L
iL Duratec-1 6V (Sigma) 303-01 A-41
IN-VEHICLE REPAIR
Discard the retaining bolts.
3. Turn the camshafts to TDC on cylinder
number
1 and install the special tool.
4. Remove the blanking plug and install the
special tool.
Carefully turn the crankshaft against the
special tool.
5.
N0TE:lnstall a new timing belt.
N0TE:lnstall the timing belt, beginning with the
crankshaft timing pulley working counterclockwise.
Install the timing belt.
6. Measuring the depth of the threaded hole in
the crankshaft.
Depth of the threaded = 42 mm: Use an
M12x29 mm crankshaft pulley center bolt.
Depth of the threaded
= 52 mm: Use an
MI 2x44,5 mm crankshaft pulley center bolt.
7. Attach the timing belt lower cover.
8. N0TE:lnstall a new crankshaft pulley
retaining bolt.
Install the crankshaft pulley.
Tighten the crankshaft pulley retaining bolt
in two stages.
Stage1:45Nm.
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-42 Duratec-1 6V (Sigma)/lm6L Duratec-1 6V (Sigma) 303-01 A-42
IN-VEHICLE REPAIR
Stage 2: 90 degrees.
Engines with eccentric cam timing belt
tensioner
Tension the timing belt by turning the
tensioner clockwise until the arrow points in
line with the center of the rectangular hole
and tighten the bolt.
9. Install the timing belt tensioner. Vehicles built 0912003 onwards
10. Tension the timing belt.
Tension the timing belt by turning the
tensioner counterclockwise until the arrow
points at the mark and tighten the bolt.
I*' AWARNING:D~ not remove the special
tool, until the timing belt is correctly
positioned. Failure to follow this instruction
may result in personal injury, or may
damage the timing belt tensioner.
Install the timing belt tensioner.
/--
13. Tension the timing belt.
Remove the special tool.
Engines with slotted bracket timing belt
tensioner
I I. Install the timing belt tensioner and tension
the timing belt.
Screw in the bolts finger tight.
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-011 Am43 Duratec-1 6V (Sigma)lII6L Duratec-I 6V (Sigma) 303-01 A-43
IN-VEHICLE REPAIR
Vehicles built 0412005 onwards 16. Remove special tool.
/ 14' AWARNING:D~ not remove the special
tool, until the timing belt is correctly
positioned. Failure to follow this instruction
may result in personal injury, or may
damage the timing belt tensioner.
Tension the timing belt.
Remove the special tool.
All vehicles
15. CAUTIONS:
( , nlnstall a hose (order no. E890438S) to
the special tool studs, to prevent damage
to the camshaft pulleys. 17.
Remove the special tool.
ADO not tighten the camshaft pulley bolts 18. N0TE:Only turn the engine in its normal
against the timing plate. direction
of rotation.
N0TE:The camshafts must remain at TDC. Turn
the engine two revolutions.
N0TE:lnstall new camshaft pulley retaining bolts. 19. Install the special tool.
Using the special tool, tighten the camshaft Carefully turn the crankshaft against the
pulleys. special tool.
20. Check the valve timing.
If necessary loosen the camshaft pulleys and
correct the camshaft alignment.
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-44 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-44
IN-VEHICLE REPAIR
* Remove the special tool.
21. Remove the special tool.
22. Install the blanking plug.
23. Using the special tool, install the spark
plugs.
Apply grease to the spark plug threads.
24. Install the engine front mount bracket.
Tighten the bolts in the indicated order in
three stages.
Stage 1 : Hand tighten bolt 1.
Stage 2: Tighten bolts 2 to 55 Nm.
Stage 3: Tighten bolt 3 to 55 Nm.
25. Install the timing belt upper cover.
26. N0TE:lnstall new engine front mount
retaining nuts.
2006.0 Fiesta 121zo06 GI 83738en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llm4L
303-01A-45 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-45
IN-VEHICLE REPAIR
lnstall the engine front mount.
27. Remove the
trolley jack.
28. Attach the generator.
1. lnstall the stud and nut.
2. lnstall the bolt.
3. Tighten the bolt.
31. lnstall the timing belt upper cover retaining
bolts.
32. N0TE:Do not tighten the coolant pump
pulley retaining bolts at this stage.
lnstall the coolant pump pulley.
I 33. lnstall the accessory drive belt.
29. Connect the generator electrical connector.
For additional information, refer to:
Accessory Drive
Belt - 1.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
30. Raise and support the vehicle.
For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
and Operation).
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
27. Remove the exhaust manifold upper heat
shield 30.
Detach the oil level indicator tube from the
intake manifold.
f
28. Detach the exhaust manifold and position
31. CAUTIONS:
it to one side. A~he cylinder head must have cooled to
Discard the nuts and the exhaust manifold below 30°C before removal.
gasket.
A~osition the cylinder head on a soft
surface.
A~emove the cylinder head bolts in the
sequence shown.
Using the special tool, remove the cylinder
-
head bolts.
Discard the cylinder head gasket.
29. Remove the timing belt rear cover (engine
shown removed for clarity).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 A-59 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-59
IN-VEHICLE REPAIR
installation 2. Attach the oil level indicator tube to the
intake manifold.
! ACAUTION:T~~ thickness of the new
cylinder head gasket must be the same as
that of the old one (hole marked).
N0TE:lnstall a new cylinder head gasket.
N0TE:Position the cylinder head into the two guide
sleeves.
Using the special tool, install the cylinder
head.
Tighten the cylinder head bolts in the
sequence shown in three stages.
Stagel: 15Nm.
Stage 2: 30 Nm.
Stage 3: 90 degrees. 3. Install the timing belt rear cover (engine
shown removed for clarity).
4. N0TE:lnstall a new exhaust manifold gasket
and new exhaust manifold retaining nuts.
N0TE:Do not fully tighten the nuts and bolt at this
stage.
Install the exhaust manifold.
5. Tighten the exhaust manifold upper retaining
nuts and bolt in the sequence shown in two
stages.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A-66 Duratec-1 6V (Sigma)/l.GL Duratec-1 6V (Sigma) 303-01 A-66
IN-VEHICLE REPAIR
Oil Pump(21 714 0)
Special Tool(s)
Removal
1. Remove the timing belt.
For additional information, refer to Timing
Belt in this section.
2. Remove the crankshaft timing belt pulley.
3. Detach the air conditioning (AIC) compressor
from the cylinder block and position
it to one
side.
4. Remove the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Detach the oil pick-up tube from the oil pump
and remove the oil pump (engine shown
removed for clarity).
Discard the gaskets.
Remove and discard the crankshaft front oil
seal.
Installation
1. N0TE:lnstall a new oil pump gasket.
Install the oil pump (engine shown removed
for clarity).
2. N0TE:lnstall a new oil pump intake pipe
gasket.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 A-67 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-67
IN-VEHICLE REPAIR
Attach the oil pick-up tube to the oil pump 6. Install the crankshaft timing belt pulley.
(engine shown removed for clarity).
7. Install the timing belt.
3. N0TE:lnstall a new crankshaft front oil seal.
For additional information, refer to Timing
Using the special tool, install the crankshaft Belt
in this section.
front oil seal.
4. Install the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Attach the air conditioning (AIC) compressor
to the cylinder block.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
DISASSEMBLY
Engine(21 134 8)
Special Tool(s)
I I Slide Hammer I
I I Universal Flange Holding I
I I Locking Tool, Flywheel
21167
Mounting Stand
303-435 (2 1 -1 87)
Socket, Cylinder Head Bolt
303-392 (21 -1 67)
Mounting Bracket for 303-435
303-435-06 (21 -031
B)
I I Socket, Spark Plug
Special
Tool(s)
Adapter
for 205-047
303-633 (2 1 -227)
0 0
0 ES21212
Locking Tool, Timing Belt
Tensioner
303-1 054
Mounting Plate for
303-435-06
303-435-1 4A (21 -2 12A)
General Equipment
I Securing straps I
I Engine hoist I
I Oil filter strap wrench I
All vehicles
1. Remove the engine wiring harness.
2006.0 Fiesta 1212006 GI 54224en
procarmanuals.com