display FORD FOCUS 2012 3.G Workshop Manual

911 operators to provide the most appropriate emergency
services. If you do not want to disclose this information, do not
enable (set to ON) the feature.
Note:If 911 Assist™ is enabled/disabled by any user, the current setting
will apply for all paired phones. If the 911 Assist™ setting is disabled
(set to OFF), a voice message and/or display item will inform the vehicle
occupants when a previously paired phone connects to SYNCat vehicle
start up.
In the event of a crash involving the deployment of an airbag or the
activation of the fuel pump shut-off, in certain vehicles, SYNCis
designed to assist occupants in attempting to contact emergency services
by dialing 911 through the occupant’s paired and connectedBluetooth
enabled cellular phone. In the event that a connected cellular phone is
damaged or loses connection to SYNC, SYNCwill search for and
connect to any available, previously paired cell phone and attempt to
place the call to 911. Before initiating the call, SYNCprovides a short
window of time (approximately 10 seconds) that allows the driver or
passenger to decide whether to cancel the call by pressing and
holding
or PHONE on the steering wheel controls or on the audio
system. Before initiating the 911 call for the occupants, SYNCwill say
the following or a similar message:
“SYNCwill attempt to call 911. If you wish to cancel the call, press and
hold the phone button.”
If the call is not cancelled and a successful call is made, a pre-recorded
message will be played for the 911 operator and then the occupant(s) in
the vehicle will be able to communicate with the 911 operator.
Note:Failure to cancel the call as described above will result in SYNC
dialing 911.
Note:When you are connected to the 911 operator, be prepared to
provide your name, phone number and location immediately, because not
all 911 systems are capable of receiving this information electronically.
The following steps are required for the 911 Assist™ feature to perform
properly:
•SYNCis on and functioning properly at the time of the incident and
throughout feature activation and use.
•SYNC911 Assist™ feature is set to ON prior to the incident.
•ABluetoothenabled and compatible cellular phone is paired and
connected to SYNC.
•A connectedBluetoothenabled cellular phone that has the ability to
make and maintain an outgoing call at the time of the incident.
Entertainment Systems
85
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

•A connectedBluetoothenabled cellular phone that has adequate
network coverage, battery power and signal strength.
•The vehicle is located in the U.S. or Canada or in a territory in which
911 is the emergency number.
WARNING:Unless 911 Assist™ is previously configured to ON
prior to a crash, 911 Assist™ will not dial for help during an
emergency, which could delay response time, increasing the risk of
serious injury or death after a crash.
The 911 Assist™ feature is initially set to OFF. To access the setting:
1. Press
or PHONE to enter thePhone Menu.
2. Scroll repeatedly until911 Assistappears in the radio display.
3. Press OK to confirm and enter the911 Assistmenu.
4. Scroll to select between On and Off selections.
5. Press OK when the desired option appears in the radio display. Set On
or Set Off will appear in the display as confirmation.
Note:Off selections include: Off with reminder and Off without
reminder. Off with reminder provides a display and voice reminder at
phone connection at vehicle start. Off without reminder provides a
display reminder only without a voice reminder.
For more information, please visit www.SyncMyRide.com or
www.syncmaroute.ca.
Note: Before enabling (setting to ON), review the 911 Assist™
Privacy Notice.
Vehicle health report (if equipped, U.S. only)
WARNING:Always follow scheduled maintenance instructions,
regularly inspect your vehicle, and seek repair for any damage or
problem you suspect. Vehicle Health Reports supplements, but cannot
replace normal maintenance and vehicle inspection. Vehicle Health
Report only monitors certain systems that are electronically monitored
by the vehicle and will not monitor or report the status of any other
system, (i.e., brake lining wear). Failure to perform scheduled
maintenance and regularly inspect your vehicle may result in vehicle
damage and serious injury.
Note: Your Vehicle Health Report feature requires activation
prior to use. Visit www.SyncMyRide.com to register.There is no fee
or subscription associated with Vehicle Health Report, but youmust
register to use this feature.
Entertainment Systems
86
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

To connect using voice commands:
1. Plug the device into the vehicle’s USB port.
2. Press VOICE or
and when prompted, say, “USB”.
3. You can now play music by saying any of the appropriate voice
commands. Refer to theMedia voice commands.
To connect using the system menu:
1. Plug the device into the vehicle’s USB port.
2. Press AUX.
3. Press MENU to enter theMedia Menu.
4. Scroll untilSelect Sourceappears and press OK.
5. Scroll to select USB and press OK.
6. Depending on how many digital media files are on your
connected device,Indexingmay appear in the radio display until
indexing is complete. You will then be taken to thePlay Menu.
7. Press OK and scroll through selections of:
•Play All
•Albums
•Genres
•Playlists
•Tracks
•Explore USB
•Similar Music
•Return
5. When the desired selection appears in the display, press OK to
build your desired music selection.
For more information, refer toAccessing your play menulater in
this chapter.
What’s playing?
At any time while a track is playing, you can press
and say, “What’s
playing?”. SYNC will read the metadata tags of the playing track to you
(if populated).
Entertainment Systems
89
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Media Settings: Allows you to choose to shuffle or repeat your music in
addition to setting your Autoplay settings. Press OK to select and then
scroll to choose from:
•Shuffle: Press OK to shuffle available media files in the current
playlist.Note:To shuffle all media tracks, you must selectPlay All
in the Play Menu and then select Shuffle.
•Repeat: Press OK to repeat any song.
•Autoplay: Press OK to listen to music which has already been
randomly indexed during the indexing process.
Note:Once these selections are turned on, they will remain on
until turned off. Some digital media players require both USB and
Line in ports to stream data and music separately.
Applications (if available):You can download new software
applications (if available) and then load the desired applications onto
SYNC through your USB port. Please refer to www.SyncMyRide.com or
www.syncmaroute.ca for more information.
System Settings: Allows you to accessBluetoothDevice menu listings
(add, connect, set as primary, on/off, delete) as well as Advanced menu
listings (prompts, languages, defaults, master reset, install application
and system information).
•Please refer toSystem Settingsin this chapter for complete
information.
Exit Media Menu: Press OK when this appears to exit the media menu.
Accessing your play menu
The Play menu allows you to select and play your media by artist, album,
genre, playlist, track, similar music or even to explore what is on your
USB device.
To access:
1. Press AUX and then MENU to access theMedia Menu.
2. Scroll to select thePlay Menuand press OK.
3. If there are no media files to access, the display will indicate there is
no media. If there are media files, you will then have the following
options to scroll through and select from:
Play All: Allows you to play all indexed media (tracks) from your
playing device in flat file mode, one at a time in numerical order.
Entertainment Systems
94
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

•Press OK to select. The first track title will appear in the display.
Artists: Allows you to sort all indexed media by artist. Once selected,
the system will list and then play all artists and tracks alphabetically. If
there are less than 255 indexed artist, they will be listed alphabetically in
flat file mode. If there are more, they will be categorized into
alphabetical categories.
1. Press OK to select. You can select to playAll Artistsor any
indexed artist.
2. Scroll until the desired artist is chosen and press OK.
Albums: Allows you to sort all indexed media by albums. If there are
less than 255 indexed albums, they will be listed alphabetically in flat file
mode. If there are more, they will be organized into alphabetical
categories.
1. Press OK to enter the album menu and select from playing all
albums or from any individual indexed album.
2. Scroll until the desired album is chosen and press OK.
Genres: Allows you to sort indexed music by genre (category) type.
SYNC will list the genres alphabetically in flat file mode. If there are
more than 255, SYNC will automatically organize them into alphabetical
categories.
•Press OK to select and then scroll to select the desired genre
and press OK.
Playlists: Allows you to access your playlists. SYNC will list your
playlists alphabetically in flat file mode. If there are more than 255,
SYNC will automatically organize them into alphabetical categories.
Note:SYNC supports many playlist formats such as: .ASX, .M3U, .WPL,
.MTP.
•Press OK to select. Then scroll to select the desired playlist and
press OK.
Tracks: Allows you to search for and play a specific track which has
been indexed. SYNC will list your tracks alphabetically in flat file mode.
If there are more than 255, SYNC will automatically organize them into
alphabetical categories.
•Press OK to select. Then scroll to select the desired track and
press OK.
Entertainment Systems
95
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

4. Press OK and then scroll to select from the following:
Add Bluetooth Device: This is a speed dependent featurewhich
allows you to pair additional devices to the system.
1. Press OK to select and press OK again whenFind SYNCappears
in the display.
2. Follow the directions in your phone’s user guide to put your
phone into discovery mode. A six digit PIN will appear in the
display.
3. When prompted on your phone’s six digit display, enter the PIN.
You can now change SYNC sources to BT Audio and stream music
from your device.
Connect Bluetooth Device: Allows you to connect a previously paired
Bluetoothenabled phone.
1. Press OK to select and view a list of devices.
2. Scroll until the desired device is chosen and press OK to connect
the device.
Set Bluetooth On/Off: Allows you to turn theBluetoothfeature on /off.
•Press OK and scroll to toggle between On and Off. When the
desired selection is chosen, press OK.
Note:Turning OffBluetoothwill disconnect allBluetoothdevices
and deactivate allBluetoothfeatures.
Delete Device: Allows you to delete a paired media device.
•Press OK and scroll to select the device. Press OK to confirm.
Delete All Devices: Allows you to delete all previously paired devices.
•Press OK to select.
Return: Press OK to exit the current menu.
Advanced menu options
This menu allows you to access settings such as prompts, language,
performing a master reset as well as returning to factory defaults.
To access:
1. Press AUX and then MENU to access theMedia Menu.
2. Scroll untilSystem Settingsappears and select OK.
3. Scroll untilAdvancedappears.
Entertainment Systems
98
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

4. Press OK and then scroll to select from the following:
Prompts: Prompts from SYNC can help guide you via questions, helpful
hints or ask you for a specific action. To turn these prompts on or off:
1. Press OK to select and scroll to select between on or off.
2. Press OK when the desired selection appears in the display.
SYNC will take you back to the Advanced menu.
Languages: Allows you to choose from three languages:English,
FrancaisandEspanol. Once selected, all of SYNC’s radio displays and
prompts will be in the selected language.
1. Press OK to select and then scroll throughEnglish,Francais
andEspanol.
2. Press OK when the desired selection appears in the display.
Note:If you change the language setting, the display will indicating
that the system is updating. When complete, SYNC will take you
back to theAdvancedmenu.
Factory Defaults: Allows you to return to the factory default settings.
This selection will NOT erase your indexed information (phonebook, call
history, text messages and paired devices).
1. Press OK to select and then press OK again whenRestore
Defaults?appears in the display.
2. Press OK to confirm.
Master Reset: Allows you to completely erase ALL information stored
on SYNC (all phonebook, call history, text messages and all paired
devices) and return to the factory default settings.
•Press OK to select. The display will indicate when complete and
SYNC will take you back to theAdvancedmenu.
Application (if available):You can download new software application
(if available) and then load the desired applications onto SYNC through
your USB port. Refer to the web site for more information.
Return: Press OK to exit the current menu.
Entertainment Systems
99
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Voice command issues
Issue Possible
Cause(s)Possible Solution(s)
SYNC does not
understand or is
calling the wrong
contact when I
want to make a
call.•You may be
using the wrong
voice commands.
•You may not be
saying the name
exactly as it is
saved.
•Contacts in
your phonebook
may be very short
and similar, or
they may contain
special
characters.
•Your
phonebook
contacts may be
saved in CAPS.•Review the phone voice
commands at the beginning of
the phone chapter.
•Ensure that you are saying
the contacts exactly as they are
listed. For example, if a contact
is saved as Joe Wilson, say, “Call
Joe Wilson”.
•The system does better if you
list full names such as “Joe
Wilson” rather than “Joe”.
•Don’t use special characters
such as 123 or ICE as the
system will not recognize them.
•If contacts are saved in CAPS,
you will have to spell them.
JAKE will require you to say, “
Call J-A-K-E.”
Helpful Hints
•Ensure that the interior of the vehicle is as quiet as possible. Wind
noise from open windows and road vibrations may prevent the system
from correctly recognizing spoken voice commands.
•Ensure that you are speaking naturally and without any large pauses
between words.
•After you press
to begin a voice session, wait until the prompt
sounds andListeningappears in the display. Anything spoken prior to
this will not register with the system.
•You can, at any time, interrupt the system while it is speaking by
pressing
during an active voice session. The system will respond
with a listening prompt and allow you to speak a command.
•For a list of available voice commands, you can press
and say,
“Help” after the tone. The system will audibly list voice commands
available in your current mode.
Entertainment Systems
106
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Digital media player / USB Device:This is a generic term used to
signify any of the following media devices: iPod, Zune™, “Plays from
device” players, and most USB drives (thumb drives, flash drives, PEN
drives, etc.)
Discoverable mode:A mode which allows otherBluetoothenabled
devices to find yourBluetoothenabled device.
Discovery mode:A mode which allows yourBluetoothenabled device
to search for other ‘discoverable’Bluetoothenabled devices.
In-band ringing:This is a phone dependent feature. If yourBluetooth
enabled cellular phone supports this feature, SYNCcan play your ring
tone during incoming calls.
Indexing:A process in which SYNCbuilds a voice recognition grammar
for the media content of your digital media player. While indexing,
SYNCwill play already indexed media if Autoplay is on. However, voice
recognition is not available for the media until the indexing process is
complete.
Metadata:Descriptive tags embedded in your digital media which
provide SYNCwith information such as ARTIST, ALBUM, GENRE and
TRACK.
Pairing:To use yourBluetoothenabled cellular phone with SYNC, you
must go through a pairing (bonding) process. “Pairing” is a special
process used when two devices connect for the first time. The pairing
process is used to generate a link key that is used for authentication
purposes during subsequentBluetoothconnections between the two
devices.
PIN (Personal Identification number):This six digit number
(sometimes referred to as a passkey) will be shown in the radio display
during the pairing process with yourBluetoothenabled device. You do
not need to write down this number as it will only be used for that
specific pairing procedure.
Entertainment Systems
114
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM
(IF EQUIPPED)
Temperature conversion:To switch between Fahrenheit and Celsius:
Press MENU > Display Settings > Temp. Setting. If your vehicle is
equipped with the touchscreen system, press Menu > Settings > System
> Temperature.
1.
(Power):Press to turn the system on or off.
2.
MAX:(Max Defrost):Distributes outside air through the
windshield defroster vents and demister vents. Can be used to clear the
windshield of fog and thin ice. Press this button again to return to the
previous air flow selection.
3.MAX A/C:Press to distribute recirculated air through the instrument
panel vents to cool the vehicle. This re-cooling of the interior air is more
economical and efficient. Recirculated air may also help reduce
undesirable odors from entering the vehicle.
Passenger setting:Turn this knob to activate the passenger settings
(dual zone) and to increase/decrease the temperature for the passenger
side of the vehicle. To return to single zone (MONO mode), press and
hold AUTO.
AUTO
A/C
MAX
A/CMAX
1102113
456789
Climate Controls
118
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)