brake FORD FOCUS 2014 3.G Quick Reference Guide

insTrumenT paneL
1 Trunk*/Liftgate* Release
2 Cruise Control*
To Set Your Cruise Control Speed
1. Press the ON control and release.
2. Accelerate to the desired speed.
3. Press the SET + control and release,
then take your foot off the accelerator.
After you set your speed, you can press
SET +/ SET – to adjust your cruise speed. To
disable, tap the brake, press the clutch pedal
or pull the CAN (Cancel) control toward you.
Note: Using the clutch pedal to cancel a set
speed may cause the engine speed to
increase briefly.
3 Information Display
Provides information about various systems
on your vehicle. Use the left, 5-way controls
located on the steering wheel to choose and
confirm settings and messages. Refer to the
Information Displays chapter of your Owner’s
Manual for more information.
4 Service Engine Soon Light
Illuminates briefly when the ignition
is turned on. If it remains on or is blinking after the engine is started, the On-Board
Diagnostics (OBD-II) system has detected a
malfunction.
Drive in a moderate fashion and
contact your authorized dealer as soon
as possible.
5 Tilt/Telescope Steering Column
Unlock the steering wheel by pulling the
lever down. Adjust the wheel to the desired
position. Push the lever back up to lock the
steering wheel in place.
6 Voice Controls*
Pull toward you to access
voice recognition.
Press to answer a call.
Press to exit phone mode or end a call.
7 Push Button Start*
Allows you to start your vehicle by pressing
the ENGINE START/STOP button while
fully pressing down on the brake (automatic
transmission) or clutch and brake (manual
transmission) pedal(s). Press the button
again to turn the engine off.
Note: Your intelligent access key must be
inside the vehicle for keyless starting to work.
8 Audio Controls*
Use the right-hand, 5-way controls to
adjust your audio system:
(Volume): Press to increase (+)
or decrease (–) volume levels.
(Seek): Press the right arrow to hear the
next saved radio station, CD track or MP3 choice.
Press the left arrow to hear the previous selection.
Press M to select a different audio source.
9 Wiper Controls
Use the rotary control on the stalk to adjust the
wipe intervals. Pull the stalk toward you to spray
and wash the windshield. Press the button at the
end of the lever to turn the rear wiper* on, off or
change to intermittent wipe.
10 Hazard Control
11 Power Door Locks
Press the control to lock or unlock
the doors. When the light on the
button is on, it indicates that all
of the doors and the luggage compartment are
locked. When the light is off, it indicates that either
the luggage compartment or one or more of the
doors are unlocked.
2014 focus
4*if equipped
26
38
5
49
1011
3
7
5
1
*if equipped

sync®*
Why Do I Need a SYNC Owner Account?
A SYNC owner account is required for Vehicle Health Report
activation and the ability to view your reports online. You’ll
also be able to take advantage of all of SYNC’s Services*
and personalization features, such as saving your Favorites
and Points of Interest. You’ll receive the latest software
updates that add new places, directions and information;
and if you have questions, you’ll get free customer support.
Note: Your SYNC system may offer advanced features such
as SYNC Services, AppLink
TM and Vehicle Health Reports. Visit
the website or call the toll-free number for more information.
See the inside front cover of this guide for details.

Using My Phone with SYNC
Note: You must download your phone book to make phone
calls with voice commands by name.
Making a Phone Call
Use SYNC to make a phone call to anyone in your phone
book by pulling the voice control
. When prompted, give a
voice command.
For example, you could say “Call Jake Smith at home”.
SYNC repeats the command back to you and dials
the number.
Note: You can also make phone calls by pulling the voice
button
. When prompted, give the voice command “Dial”,
then say the phone number. Answering Incoming Calls
Whenever you have an incoming call, you will be able to see
the name and number of the person calling in your display.
Press the phone button
to answer an incoming call. You
can hang up at any time by pressing the phone button .
Do Not Disturb Mode
This feature blocks incoming calls and text messages, and
saves them for later. You still have access to outgoing calls
when this feature is active. Say the voice command “Do not
disturb on” to enable and “Do not disturb off” to disable.
Using SYNC to Access Digital Media
Plug in your USB media devices such as phones and MP3
players, and use SYNC to play all of your favorite music.
Note: SYNC indexes your music. The more music that is
stored on your device, the longer it takes SYNC to index.
Using Voice Commands to Play Music
1. Plug your media player into your USB port.
2. Pull the voice control
. When prompted, say
“USB”, then follow-up saying a voice command.
7*if equipped
*if equipped
Getting Started with
Your SYNC System
SYNC is a hands-free, voice
recognition system used for
entertainment, information
and communication.
SYNC. Say the Word.
Before You Get Started
1. Set up your owner account at
SyncMyRide.com (U.S.) or
SyncMyRide.ca (Canada).
Register by following the
on-screen instructions. After
registering, you can see what
available services you are
eligible for.
2. SYNC uses a wireless
connection called
Bluetooth®
to communicate with your phone.
Turn Bluetooth mode on in your
phone’s menu options. This lets
your phone find SYNC. If you
need more details on setting
up your phone with SYNC, visit
SyncMyRide.com (U.S.) or
SyncMyRide.ca (Canada), or your
phone manufacturer’s website.
Pairing Your Phone
with SYNC
In order to use many of the features
of SYNC, you must first pair and
connect your phone with SYNC.
To Pair Your Phone for the First Time
1. Make sure that your vehicle is in
P (Park) or N (Neutral) with the
parking brake applied (for vehicles
with manual transmissions only)
and both your ignition and radio
are switched on.
2. Press the phone button. When
the display indicates no phone is
paired, press OK.
3. When Find SYNC appears in the
display, press OK.
4. Put your phone into Bluetooth
discovery mode. See your phone’s
user guide, if necessary.
5. When prompted on your phone’s
display, enter the six-digit PIN
provided by SYNC in the
radio display.
6. The display will indicate when the
pairing is successful. The System May Prompt You to

• Set your phone as primary/
favorite (the primary phone
will receive messages
and voicemails).
• Download your phone book
(this is required to use the full
set of voice commands).
• Turn on 911 Assist
®.
Tips
• Make sure you accept SYNC’s
request to access your phone.
• To pair subsequent phones,
please refer to Pairing
Subsequent Phones in the SYNC
chapter of your Owner’s Manual.
• If you are experiencing pairing
problems, try performing a clean
pairing by deleting your device
from SYNC, deleting the SYNC
connection from your phone, and
then repeating the Pairing your
Phone with SYNC process.

6
2014 focus

2014 focussync® wiTh my ford Touch®* continued
Climate
SYNC with MyFord Touch controls the temperature,
airflow direction and fan speed for you and
your passenger.
To use voice commands to operate the climate controls,
say a voice command like “Climate temperature 72
degrees” and MyFord Touch will make that adjustment.
Set Your Temperature
• Touch the lower-right, blue corner on the touchscreen.
• Set your exact, desired temperature using the
+ or – buttons.
Entertainment
No matter how you store your music, SYNC makes it
yours to enjoy when you’re behind the wheel. Just press
the lower-left, red corner of the touchscreen. From here,
you can easily go between AM/FM, Sirius and other media
sources. You use your touchscreen or the audio controls
on your steering wheel to interact with your digital media.
Bring in Your Own Music
Gain access to any audio source by voice and even control
how each operates, like changing radio stations, CD tracks
or music on one of the following devices:
• USB
• Bluetooth
®
Streaming
• SD Card
• A/V In
For additional support, refer to your Owner’s Manual, visit
the website or call the toll-free number. See the inside
front cover of this guide for details.
1011
conVenience
Intelligent Access Key*
Note: Your intelligent access key must be within 3 feet
(1 meter) of your vehicle.
To unlock a front door: Pull the front exterior door handle.
To lock all of the doors: Press and hold the door handle
lock sensor.
To unlock and open the trunk: Press the exterior trunk
release button near the license plate.
The intelligent access key also contains a mechanical
key blade, which can be used to unlock the driver door,
if necessary.Remote Start*
Remote start allows you to start the engine from outside
your vehicle using your transmitter.
To Start
1. Press
and then press twice within three seconds.
2. Once inside, apply the brake while pressing the ENGINE
START/STOP button.
3. Shift into D (Drive) and go.
If You Have an Integrated Keyhead Transmitter
1. Insert the key into the ignition.
2. Turn the ignition on as you normally would before driving.
To turn the engine off from outside the vehicle after
using your remote start: Press
once.
MyKey®
Allows you to program speed
restrictions, limited volume
levels, safety belt reminders
and more. For complete
information, refer to the
MyKey chapter in your
Owner’s Manual.
*if equipped
*if equipped

funcTion continued2014 focus
Ambient Lighting*
The ambient lighting system illuminates the interior with
a choice of several colors. The ambient lighting control
is located in the overhead console. Rotate the control
knob to switch the feature on and adjust the desired
brightness. Press the palette button to cycle through
your color choices.
Ambient lighting will switch on when the following
conditions have been met:
• You switch the ignition on, or
• You switch the headlamps on.
Traction Control
The traction control system helps avoid drive wheel
spin and loss of traction.
If your vehicle begins to slide, the system applies
the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels
spin when accelerating on slippery or loose surfaces,
the system reduces engine power in order to
increase traction.
In certain situations (for example, stuck in snow or
mud), turning the traction control off may be beneficial
as this allows the wheels to spin with full engine power.
Turn the traction control system off through
the information display.
AdvanceTrac® Stability Control System
The system helps you keep control of your vehicle when
on a slippery surface. The electronic stability control
portion of the system helps avoid skids and lateral slides,
while the traction control system helps avoid drive wheel
spin and loss of traction.
Interior Lamps
The lamps will switch on when you open any door, press
a remote control button or press the overhead control.
Press
to switch off the
door illumination function
when you open any door.
Press
again to switch
the door illumination
function back on.
Press
to turn the
overhead lamps on and off.
comforT2014 focus
Tilting Head Restraints*
Your vehicle’s front-row head
restraints can be adjusted.
To raise: Pull up on the
head restraint.
To lower: Press the head
restraint down while pressing
and holding the guide sleeve
adjust/release button.
To tilt the head restraint: Gently pull the top of the head
restraint forward.
To return it to its upright position: Tilt it forward once
more and release.
Note: Do not attempt to force the head restraint backward
after it is tilted. Instead, continue tilting it forward until the
head restraint releases to the upright position.
Heated front Seats*
The heated front seat controls are located on the center
console near the gearshift lever.
To Use, Simply
• Adjust the dial to the desired
heat setting.
• Choose from 0–5 (off-high).

Front-Seat Adjusters
Height/Recline Adjustment
Lift the control to adjust the height
of the seat. Lift the control to adjust the angle
of the seatback.
Dual Zone Temperature Control*
You can operate the
temperature with one control,
called single zone, or two,
called dual zone where both
driver and front passenger
can select independent
temperatures using their own
rotary dials.
To operate the dual zone: Use the rotary control on the
passenger’s side. Single zone automatically shuts off.
You can now adjust the driver’s side and passenger’s side
temperatures independently.
To return back to single zone: Press and hold the AUTO
button for 2–4 seconds. The passenger’s temperature
switches to the driver’s temperature setting.
Height
Adjustment
Control
Seatback
Recline
Control
1415*if equipped *if equipped