technical data FORD KUGA 2011 1.G Workshop Manual

 .XJD
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALBACK TO FRONT PAGE
VIEW MAIN INDEX
Tothebestofourknowledge,theillustrations,technicalinformation,dataanddescriptionsin
thisissuewerecorrectatthetimeofgoingtoprint.Therighttochangeprices,specifications,
equipmentandmaintenanceinstructionsatanytimewithoutnoticeisreservedaspartofFORD
policyofcontinuousdevelopmentandimprovementforthebenefitofourcustomers.
Nopartofthispublicationmaybereproduced,storedinadataprocessingsystemortransmitted
inanyform,electronic,mechanical,photocopy,recording,translationorbyanyothermeans
withoutpriorpermissionofFord Motor Company.Noliabilitycanbeacceptedforany
inaccuraciesinthispublication,althougheverypossiblecarehasbeentakentomakeitas
completeandaccurateaspossible.
Copyright©
FOREWORD

Types of self-locking nuts and bolts
NOTE:There are more types of self-locking fasteners available than shown in following illustration.
E126782
123
4567
Description
Item
Completely coated self-locking bolt
1
Partially coated self-locking bolt
2
Self-locking bolt with a locking washer
3
Self-locking nut with a plastic locking insert
4
Self-locking nut with thread deformation
(3 identations)
5
Self-locking nut with thread deformation
(to oval shape)
6
Self-locking nut with integrated locking ring
7
• All types of seals and gaskets must be discarded and new seals and gaskets installed
unless otherwise stated within the procedure.
• Nuts and bolts with a chemical coating for locking and/or sealing and/or antiseize must be
discarded unless the procedure advises to
reapply the coating with a specified material. • Nuts and bolts with a mechanical locking such
as thread inserts, thread deformation or locking
washers must be discarded and new nuts and
bolts installed unless otherwise stated within
the procedure.
• Torque to yield bolts must be discarded and new torque to yield bolts installed unless
otherwise stated within the procedure,
recognizable by a tightening torque with more
than one stage together with a torque angle.
Reuse of exterior trim parts
All type of glued exterior trim parts or parts
fastened with adhesive tape must be discarded
and new parts installed unless otherwise stated
within the procedure.
Specification data
Specification procedures will only contain technical
data that is not already part of a repair procedure.
Sequence of tasks
If components must be removed or installed in a
specific sequence, the sequence will be identified
G836098en2008.50 Kuga8/2011
100-00- 5
General Information
100-00- 5
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Vehicles with upgraded audio system.
The upgraded audio system is available with the
following equipment:
• • Radio/individual CD player with MP3
• • Radio/individual CD player with MP3 and
Digital Audio Broadcasting (DAB)
• • Radio with integrated 6x CD changer with MP3
• • Radio with integrated 6x CD changer with MP3
and DAB
DAB radio
DAB is a procedure for digital transmission of radio
programs.
The DAB system was developed in Europe within
the framework of a European development program
and in recent years has been introduced in many
European countries.
The audio signals from up to 12 radio stations are
packaged into a multiplex and bundled into a single
data stream. This is then broadcast via one or more
terrestrial transmitters. This means that individual
transmitters are no longer needed for each radio
station.
In addition to the much larger range of stations that
can be provided to radio listeners through DAB,
there are also several big technical advantages
over the current FM, MW, LW and SW
transmission:
• Provided the receiver can receive the signal from the DAB transmitter, sound reproduction
is guaranteed. There is no fading, as is typical
for AM and mobile FM reception.
• Interference, such as crackling noises caused by high voltage lines, is filtered out by the DAB
receiver. • With DAB, there is no overlapping of different
stations.
• If the transmission signal is reflected by natural obstacles or buildings while en route, this
causes interference with FM. With DAB,
however, reception is significantly improved by
this.
Service linking
As soon as the audio device no longer receives
the FM signal in sufficient quality, it automatically
switches to the corresponding DAB transmitter, but
the FM display in the audio device remains active.
When the FM signal becomes available again in
sufficient quality, the device automatically switches
back.
AUX port
The audio systems have an auxiliary device input
(AUX IN) which enables the playback of auxiliary
devices such as MiniDisc or MP3 players via the
vehicle's audio system. Sounds is played back
through the vehicle loudspeakers.
Radio remote control. The following functions can be controlled with the
remote control:
G1055647en
2008.50 Kuga 8/2011 415-01-9
Information and Entertainment System
415-01-9
DESCRIPTION AND OPERATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALE99207 E98650

Programmable Module Installation
Activation
5.
Install the most up-to-date software version in
IDS.
6. If, before replacing a module, it was not possible
to read out the vehicle-specific data using the
integrated diagnostic system (IDS) (the module
to be replaced does not respond) then, during
programming of the new module, the
vehicle-specific data must be entered manually
via a selection list in IDS or via a code which
can be obtained from the Technical Hotline.
7. In order to program, select the "Install
programmable module" submenu in the "Module
programming" menu tool box and then follow
the instructions.
8. The following modules must be programmed
after replacement:
•
• Anti-lock braking system module (ABS)
• Audio system module (ACM)
• CD player (CDP)
• Driver's door control unit (D-DCU)
• Passenger's door control unit (P-DCU)
• Rear left door control unit (RL-DCU)
• Rear right door control unit (RR-DCU)
• Electrical power steering (EPS)
• Generic Display Module (GDM) (vehicles
with DVD navigation system with
touchscreen)
• Generic electronic module (GEM)
• Headlamp control module (HCM) (vehicles with gas discharge headlamps)
• Instrument cluster (IC)
• Navigation system (NAV) (vehicles with navigation system)
• Parking aid module(PAM)
• Powertrain control module (PCM)
• Restraint control module (RCM)
• Rear entertainment system module (RETM) (vehicles with rear seat entertainment
system)
9. In order to configure the PCM, select the
"Programmable parameters" submenu in the
"Module programming" menu tool box and then
follow the instructions.
10. For vehicles with anti-lock braking system and
electronic stability program, these must also be configured using IDS following replacement of
the lateral acceleration sensor, yaw rate sensor
or pressure sensor. Configuration is performed
in the "Programmable parameters" menu tool
box.
G1158258en
2008.50 Kuga 8/2011 418-01-3
Module Configuration
418-01-3
GENERAL PROCEDURESTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL