ice FORD MONDEO 2014 4.G User Guide
Page 32 of 446
Downloaded from www.Manualslib.com manuals search engine The airbag will deploy during significantlateral collisions. It will also deploy duringsignificant frontal angled collisions. Thecurtain airbag will not deploy in minorlateral and frontal collisions, rear collisions,or overturns.
INFLATABLE SAFETY BELTS
Rear Inflatable Safety Belt (If
Equipped)
WARNINGS
Do not attempt to service, repair, ormodify the rear inflatable safety belt.
If the rear inflatable safety belt hasdeployed, it will not function again.The rear inflatable safety belt systemmust be replaced by an authorized dealer.
The rear inflatable safety belts are fittedin the shoulder portion of the safety beltsof the second-row outboard seatingpositions.
Note:The rear inflatable safety belts areonly compatible with belt positioningbooster seats of Group 2 and 3 whenproperly installed. See Installing ChildSeats (page 17). This is because they aredesigned to fill with a cooled gas at a lowerpressure and at a slower rate thantraditional airbags. After inflation, theshoulder portion of the safety belt remainscool to the touch.
The rear inflatable safety belt consists ofthe following:
•An inflatable bag located in theshoulder safety belt webbing.
•Lap safety belt webbing withautomatic locking mode.
•The same warning light, electroniccontrol and diagnostic unit as used forthe front safety belts.
•Impact sensors located in various partsof the vehicle.
How does the rear inflatable safety beltsystem work?
The rear inflatable safety belts willfunction like standard restraints ineveryday usage.
During a crash of sufficient force, theinflatable belt will inflate from inside thewebbing.
30Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSupplementary Restraints System
Page 38 of 446
Downloaded from www.Manualslib.com manuals search engine Many states and provinces haverestrictions for the use of remote start.Check your local and state or provinciallaws for specific requirements regardingremote start systems.
The remote start system will not work if:
•The ignition is on.
•The alarm system triggered.
•You disable the feature.
•The hood is open.
•The transmission is not in park (P).
•The vehicle battery voltage is too low.
•The service engine soon light is on.
Remote Starting the Vehicle
Note:You must press each button withinthree seconds of each other. Your vehiclewill not remote start if you do not follow thissequence.
The tag with your transmitter details thestarting procedure.
To remote start your vehicle:
1.Press the lock button to lock all thedoors.
2.Press the remote start button twice.The exterior lamps flash twice.
The horn sounds if the system fails to start,unless quiet start is on. Quiet start will runthe blower fan at a slower speed to reducenoise. It can be switched on or off in theinformation display. See GeneralInformation (page 86).
Note:If you remote start the vehicle withan integrated keyhead transmitter, you mustswitch the ignition on before driving yourvehicle. With an intelligent accesstransmitter, you must press theSTART/STOP button on the instrumentpanel once while applying the brake pedalbefore driving your vehicle.
The power windows will not work duringthe remote start and the radio will not turnon automatically.
The parking lamps will remain on and thevehicle will run for 5, 10 or 15 minutes,depending on the setting.
Extending the Vehicle Run Time
Repeat Steps 1 and 2 with the vehicle stillrunning to extend the run time for anotherremote start duration. If you programmedthe duration to last 10 minutes, the second10 minutes will begin after what is left ofthe first activation time. For example, if thevehicle had been running from the firstremote start for five minutes, the vehiclewill continue to run now for a total of 15minutes. You can extend the remote startup to a maximum of 35 minutes.
Wait at least five seconds before remotestarting after a vehicle shutdown.
Turning the Vehicle Off After RemoteStarting
Press the button once. Thevehicle and parking lamps willturn off.
You may have to be closer to the vehiclethan when starting due to ground reflectionand the added noise of the running vehicle.
You can disable or enable the remote startsystem through the information display.See General Information (page 86).
36Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingKeys and Remote Controls
Page 46 of 446
Downloaded from www.Manualslib.com manuals search engine LOCKING AND UNLOCKING
Note:Check your vehicle is locked beforeleaving it unattended.
Note:Do not leave your keys in your vehicle.
Power Door Locks
The power door lock control is on the driverand front passenger door panels.
Unlock.A
Lock.B
Door Lock Indicator
An LED on each door window trimilluminates when you lock the door. Itremains on for up to 10 minutes after youswitch the ignition off.
Door Lock Switch Inhibitor
When you electronically lock your vehicle,the power door lock switch will no longeroperate after 20 seconds. You must unlockyour vehicle with the remote control, orswitch the ignition on to restore functionto these switches. You can switch thisfeature on or off in the information display.See Information Displays (page 86).
Remote Control
You can use the remote control at any timewhen the ignition is off.
Unlocking the Doors
Press the button to unlock alldoors. The direction indicatorswill flash.
Note:The driver door can be unlocked withthe key if the remote control is notfunctioning.
Note:When you leave your vehicleunattended for several weeks, the remotecontrol turns off. Your vehicle must beunlocked and the engine started using thekey. Unlocking and starting your vehicle onceenables the remote control.
Reprogramming the UnlockingFunction
You can reprogram the unlocking functionso that only the driver door is unlocked.See Remote Control (page 32).
Locking the Doors
Press the button to lock alldoors. The direction indicatorswill flash.
Note:If any door or the liftgate is open, orif the hood is open on vehicles that have ananti-theft alarm or remote start, thedirection indicators will not flash.
Double Locking the Doors
WARNING
Do not use double locking whenpassengers or animals are inside yourvehicle. The doors cannot beunlocked or opened from the inside whendouble locked.
Double locking is a theft protection featurethat prevents someone from opening thedoors from the inside. It will only operateif all of the doors are fully closed.
Press the button twice withinthree seconds.
44Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 47 of 446
Downloaded from www.Manualslib.com manuals search engine Automatic Relocking
The doors automatically relock if you donot open a door within 45 seconds ofunlocking the doors with the remotecontrol. The door locks and the alarmreturn to their previous state.
Locking and Unlocking the DoorsFrom Inside
Use the power door lock control locatedon the driver and front passenger doorpanels.
Locking and Unlocking the Doorswith the Key Blade
Locking with the Key Blade
Turn the top of the key toward the front ofyour vehicle.
Double Locking with the Key Blade
Turn the top of the key toward the front ofyour vehicle twice within three seconds.
Unlocking with the Key Blade
Turn the top of the key toward the rear ofyour vehicle.
Note:If the child safety locks are on andyou pull the interior door handle, you willonly switch off the emergency locking, notthe child safety lock. You can only open thedoors using the exterior door handle.
Locking and Unlocking the DoorsIndividually with the Key Blade
Locking
If the central locking function fails tooperate, lock the doors individually usingthe key in the position shown.
Left-Hand Side
Turn clockwise to lock.
Right-Hand Side
Turn counterclockwise to lock.
Unlocking
If the central locking function fails tooperate, unlock the driver door and thenunlock all other doors individually bypulling the interior door handles.
Note:If the doors have been unlocked usingthis method, the doors must be lockedindividually until the central locking functionhas been repaired.
45Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 48 of 446
Downloaded from www.Manualslib.com manuals search engine MANUAL LIFTGATE
WARNINGS
It is extremely dangerous to ride in acargo area, inside or outside of avehicle. In a crash, people riding inthese areas are more likely to be seriouslyinjured or killed. Do not allow people to ridein any area of your vehicle that is notequipped with seats and safety belts. Makesure everyone in your vehicle is in a seatand properly using a safety belt. Failure tofollow this warning could result in seriouspersonal injury or death.
Make sure to close and latch theliftgate to prevent drawing exhaustfumes into your vehicle. This will alsoprevent passengers and cargo from fallingout. If you must drive with the liftgate open,keep the vents or windows open so outsideair comes into your vehicle. Failure tofollow this warning could result in seriouspersonal injury.
Note:Be careful when opening or closingthe liftgate in a garage or other enclosedarea to avoid damaging the liftgate.
Note:Do not hang anything, for example abike rack, from the glass or liftgate. Thiscould damage the liftgate and itscomponents.
Note: Do not leave the liftgate open whiledriving. This could damage the liftgate andits components.
Opening the Liftgate
Manually
Press the release button above the licenseplate to unlatch the liftgate.
With the Remote Control
Press the button twice withinthree seconds.
Closing the Liftgate
A handle is located inside the liftgate tohelp with closing.
POWER LIFTGATE (If Equipped)
WARNINGS
Do not operate the liftgate unless itis free from obstruction.
Careless opening and closing of theliftgate can override the protectionfunction and cause injuries.
46Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 49 of 446
Downloaded from www.Manualslib.com manuals search engine WARNINGS
Do not place objects on the liftgate.
Make sure you fully close the liftgateafter operation.
Operate the liftgate only when yourvehicle is stationary.
You can operate the liftgate using theremote control, the center console switch,the liftgate switch or the liftgate releasehandle.
Note:Make sure there is enough headroomto open the liftgate.
Note:If your vehicle has an automatictransmission, make sure the transmissionselector lever is in park.
Note:In extreme weather conditions,automatic opening and closing will not workwith the liftgate frozen to the seal.
Note:The liftgate will stop automaticallywhile opening and reverse some distance ifthere is an obstacle in the way.
Note:The liftgate will stop automaticallywhile closing and fully open if there is anobstacle in the way.
Note:You can manually operate theliftgate.
Liftgate Switch
Remote Control and Center ConsoleSwitch
Note:Switch the ignition on to operate theliftgate using the center console switch.
You will hear three chimes when theliftgate begins to close.
Five short chimes indicate a malfunctionwith the open or close request. This couldbe caused by one of the following:
•You switch the ignition on and thetransmission selector lever is not inpark.
•The battery voltage is below theminimum operating voltage.
•Your vehicle speed exceeds 3 mph (5km/h).
To open a fully closed liftgate, you caneither:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch.
•Use the liftgate release handle.
To fully open a partially opened liftgate,you can either:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
To stop the liftgate, you can either:
•Press the button on the remote control.A further remote control operation willbe delayed for approximately threeseconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
47Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 50 of 446
Downloaded from www.Manualslib.com manuals search engine Closing the Liftgate
WARNING
The bounce-back feature will notwork and it will not detect obstacleswhen the liftgate is in contact withthe vehicle body.
Note:Do not leave a passive key in yourvehicle when closing the liftgate. A messagewill be shown in the display. SeeInformation Messages (page 96).
Note:A recessed grip is located inside theliftgate to help with closing.
You can either:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
•Manually close the liftgate
The liftgate will close automatically whenit comes into contact with the vehicle body.
Programming the Liftgate
1.Open the liftgate.
2.Manually move the liftgate to the newrequired position.
3.Press and hold the liftgate switch forat least three seconds. You will hear achime.
KEYLESS ENTRY
General Information
The system will not function if:
•Your vehicle battery has no charge.
•The passive key frequencies arejammed.
•The passive key battery has no charge.
Note:If the system does not function, youwill need to use the key blade to lock andunlock your vehicle.
The system allows you to operate yourvehicle without the use of a key or remotecontrol.
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.These are located approximately 3.3 ft(1 m) from the front door handles and theliftgate.
Note:The system may not function if thepassive key is close to metal objects orelectronic devices, for example keys or a cellphone.
48Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 51 of 446
Downloaded from www.Manualslib.com manuals search engine Passive Key
Your vehicle can be locked and unlockedwith the passive key. You can use thepassive key as a remote control. SeeLocking and Unlocking (page 44).
Locking Your Vehicle
Locking sensors are located on each of thefront doors.
For central locking and to arm the alarm,touch a locking sensor once.
For double locking and to arm the alarm,touch a locking sensor twice within threeseconds.
Note:Your vehicle does not automaticallylock. If you do not touch a locking sensoryour vehicle will remain unlocked.
Note:When locking your vehicle, do notgrip the door handle.
Note:Keep the door handle surface cleanto make sure the system operates correctly.
Note: Your vehicle will remain locked forapproximately three seconds. When thedelay period is over, you can open the doorsagain, provided the passive key is within therespective detection range.
Two short flashes of the directionindicators confirms that all the doors andthe liftgate have been locked and that thealarm has been armed.
Liftgate
Note:The liftgate cannot be closed andwill reopen if the passive key is locatedinside the luggage compartment with thedoors locked.
Note:If a second valid passive key islocated within the liftgate detection range,the liftgate can be closed.
Unlocking Your Vehicle
One long flash of the direction indicatorsconfirms that all the doors and the liftgatehave been unlocked and that the alarmhas been disarmed.
Note:When your vehicle remains lockedfor longer than three days, the system willenter an energy-saving mode. This is toprevent the vehicle battery running out ofcharge. When your vehicle is unlocked whilein this mode, the reaction time of the systemmay be a little longer than normal. To exitthe energy-saving mode, unlock yourvehicle.
Note:A valid passive key must be locatedwithin the detection range of that door.
Unlocking Only the Driver Door
You can program the system so that onlythe driver door is unlocked. See RemoteControl (page 32).
If the unlocking function is reprogrammedso that only the driver door is unlocked thefollowing will occur:
•If the driver door is the first dooropened, all the other doors will remainlocked. All the other doors can beunlocked from inside your vehicle bypressing the unlock button. The otherdoors can be unlocked individually bypulling the interior door handle on therespective door.
•If the front passenger door is the firstdoor opened, all the doors will beunlocked.
49Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks
Page 60 of 446
Downloaded from www.Manualslib.com manuals search engine VOICE CONTROL
Push the control to select or deselect voicecontrol. See SYNC™ 2 (page 343).
CRUISE CONTROL
Type 1
Type 2
See Cruise Control (page 181).
INFORMATION DISPLAY
CONTROL
See Information Displays (page 86).
58Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSteering Wheel
Page 63 of 446
Downloaded from www.Manualslib.com manuals search engine Note:Wet or winter driving conditions withice, snow or salty road mist can causeinconsistent and unexpected wiping orsmearing.
In these conditions, you can do thefollowing to help keep your windshieldclear:
•Lower the sensitivity of the autowipersto reduce the amount of smearing.
•Switch to normal or high-speed wipe.
•Switch the autowipers off.
Highest sensitivityA
OnB
Lowest sensitivityC
The autowipers feature uses a rain sensor.You will find it in the area around theinterior mirror. The rain sensor monitorsthe amount of moisture on the windshieldand automatically turns on the wipers. Itwill adjust the wiper speed by the amountof moisture that the sensor detects on thewindshield.
Note:This autowiper feature isautomatically set to on and remains on untilyou switch it off in the information display.You can also switch the feature back on atany time. See (page 86).
Use the rotary control to adjust thesensitivity of the rain sensor. Set thecontrol to low sensitivity, and the wiperswill turn on when the rain sensor detectsa large amount of moisture on thewindshield. Set the control to highsensitivity, and the wipers will turn on whenthe rain sensor detects a small amount ofmoisture on the windshield.
Note:When you set the wiper system tointermittent wipe and the autowiper systemis on, the autowiper sensitivity settingadjusts the wiper speed according to themoisture on the windshield only. Use thewiper lever to wipe the windshieldon-demand.
Keep the outside of the windshield clean.The rain sensor is very sensitive. If the areaaround the mirror is dirty, then the wipersmay operate if dirt, mist or insects hit thewindshield.
WINDSHIELD WASHERS
Note:Do not operate the washers whenthe washer reservoir is empty. This maycause the washer pump to overheat.
To operate the washers and spray thewindshield, pull the lever toward you.
61Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingWipers and Washers