clock FORD MUSTANG 1996 4.G User Guide

243
*
[SV06700( ALL)05/95]
2. Put the nozzle all the way inside the fuel
filler pipe before pumping the fuel.
*
[SV06800( ALL)09/95]
NOTE: If you spill any fuel on the body of
your vehicle, clean it off immediately.
The fuel may dull or soften the paint
if you do not wash it off.
%*
[SV06850( ALL)08/95]
3. Replace the fuel cap completely when you
are finished. Turn it clockwise 1/4 turn until
it is tight. It will click when it is fully
tightened.
*
[SV06875( ALL)10/95]
4. Push the fuel door closed.
[SV06900( ALL)05/95]
RWARNING
If you lose the fuel cap, replace it with a
Motorcraft or equivalent fuel cap. If you
do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision, endangering you and your
passengers.
*
[SV06950( ALL)09/95]
NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer
warranty may be void for any damage
to the fuel tank and/or fuel system.
%*
[SV07500( ALL)06/95]
Choosing the Right Fuel
*
[SV07600( ALL)06/95]
Use only UNLEADED FUEL in your vehicle.
Using leaded fuel is prohibited by federal law.
Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
*
[SV07701( ALL)05/95]
Using a high-quality fuel makes your vehicle
more responsive and maintain its good fuel
economy and emissions. It should not be
necessary to add any aftermarket products to
your fuel tank if you continue to use a
high-quality fuel.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

254 %
*
[SV18600( ALL)08/95]
Checking Hoses
*
[SV18700( ALL)11/94]
Inspect all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in theMaintenance
Schedule and Recordbooklet. Repair or replace
with Motorcraft hoses or equivalent as necessary.
*
[SV18800( ALL)09/95]
Adding Engine Coolant
*
[SV18900( ALL)09/95]
RWARNING
Do not put engine coolant in the container
for the windshield washer fluid.
*
[SV18950( ALL)09/95]
If sprayed to clean the glass, engine coolant or
antifreeze could make it difficult to see through
the windshield.
[SV19000(MBC )05/95]
RWARNING
Never remove the radiator cap or vent
plug while the engine is running or hot.
[SV19030( ALL)05/95]
Follow these steps to avoid personal injury that
can be caused by escaping steam or engine
coolant.
[SV19040(MBC )03/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the
radiator cap or vent plug.
[SV19145( ALL)03/95]
2. When the engine is cool, wrap a thick towel
around the cap and turn it slowly
counterclockwise to unscrew.
*
[SV19150( ALL)09/95]
3. Step back while the pressure releases.
[SV19160( ALL)12/94]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it, and remove it.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

291 [SV46710(M )05/95]
quarter page art:0011232-B
Headlamp access covers
[SV46875(M )08/93]
3. Lift the cover and find the bulb in the
headlamp socket.
[SV47125(M )06/93]
4. Remove the electrical connector from the
bulb by lifting the connector clip upward
while pulling the connector rearward.
[SV47250(M )08/93]
5. Remove the retaining ring by turning
counterclockwise 1/8 of a turn to free it
from the socket. Then slide the ring off the
plastic base.Keep the ring.You must use it
again to hold the new bulb in place.
[SV47300(M )11/92]
6. Carefully remove the bulb assembly from its
socket by gently pulling it rearward without
turning.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

292
*
[SV47400( ALL)03/95]
Installing the headlamp bulb
*
[SV47600(MBC )02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV47800(MBC )08/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[SV47900( ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV48000(MBC )02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
[SV48075(M )05/95]
5. Reinstall the headlamp cover pushpin and
tighten until snug.
File:15rcsvm.ex
Update:Thu Mar 28 14:48:54 1996

Index 321
Cleaning your vehicle (continued)
engine compartment......... 242
exterior............... 5±6
exterior lamps............. 86
fabric................ 125
headlamps............... 86
instrument panel............ 80
instrument panel lens.......... 89
interior............... 125
interior lamps............. 89
mirrors............... 127
plastic parts.............. 7
polishing................ 6
rustproofing.............. 7
safety belts............... 21
tail lamps............... 86
upholstery and interior trim...... 125
washing............... 5±6
waxing................ 6
wheels................ 269
Climate control system
air conditioning............ 80
heating................ 80
heating only system........... 82
Clock.................. 89
Clutch
adjusting............... 272
fluid................. 272
fluid reservoir............ 272
operation while driving........ 182
recommended shift speeds....... 184
shifting the gears........... 183
specifications............. 300
Cold engine starting............ 53
Combination lap and shoulder belts . . . 9, 11
Compact disc player (see Electronic sound
system)............... 155
Console, description........... 129
File:rcixm.ex
Update:Wed Mar 27 09:41:15 1996