door lock GEELY FC 2008 User Guide

Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15, 6-10
4-10, 6-10
6-15,4-10right rear, avometer
terminal
9-15, 7-10
9-10, 7-10
7-15, 9-10Left rear, avometer
terminal
3-15, 1-10
3-10, 1-10
1-15, 3-15situations
Conduction
Conduction
Conduction
Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15
4-6
6-15right rear, avometer
terminal
9-15
7-9
7-15Left rear, avometer
terminal
3-15
1-3
1-15situations
Conduction
Conduction
Conduction
Windshield/bodywork glass/wing mirror--Electric window control system
Phenomena
Electric window does not Work(all)(electric
door lock does Not work)
Electric window does not work(all) (electric
door lock is normal)
Automation system does Not work
Only one window can not Move
Electric window system Does not workimpossible positions
1. POWER fuse(center power distribution box)
2.
window shift main relay (center Distribution box)
3. wiring harness
1. ignition switch
2. left front door control Panel assembly
3. wiring harness
4. electric window generator
1. left front door control panel assembly
2. electric window generator (driver seat)
1. left front control panel assembly
2. electric window switch
3. electric window generator
4. wiring harness
1. left front door control panel assembly
2. wiring harnesswiring harness
-
-
-
-
319
-
320
319
320
319
320
320
-
319
-.
Inspect
1. Inspect left front door control panel assembly
[68000142]
Action switch, inspect the conduction among joint terminals.
Notes: Whether it works good or bad ,it can judged by
basic function. Becauce the conduction can not inspect
by ascending or descending driver’s electric window main
switch.
Electric window does not locked
Electric window locked
Malfunction phenomena table
If the conduction does not limit to regulations, replace electric window main switch.
 319 

Windshield/bodywork glass/wing mirror--Rear ventilation window
Rear ventilation window
Change
Clues on: Please assemble by the sequence opposite with disassembling sequence. Assemble
directions could be got when necessary.
1. Disassemble the step trim board of left rear door [68010022] (referring to page 390)
2. Disassemble the step trim board of right rear door [68010024] (referring to page 390)
3. Disassemble left rear door frame sealed tape [68010059]
4. Disassemble right rear door frame sealed tape [68010060]
5. Disassemble rear seat cushion
6. Disassemble rear seat back assembly (fixed) [68010076] (referring to page 354)
7. Disassemble rear seat right back assembly (fixed) [68010079] (referring to page 352)
8. Disassemble rear seat left side back assembly (separate) [68010078](referring to page
352)
9. Disassemble left rear pillar interior trim board assembly [68010026] (referring to page
390)
10. Disassemble right rear pillar interior trim board assembly [68010027] (referring to page
390)
11. Disassemble high brake light assembly [68010008]
12. Disassemble rear platform front-below trim board [68010034]
13. Disassemble rear wind window sealed trim tape [68000104]
(a) Use blade to cut the trim tape as the drawing.
steel wire
 324 
Notes: Do not damage the bodywork by blade.
(b) Disassemble rudimental trim tape.
14. Disassemble rear ventilation window assembly
[68000103]
(a) Use a steel wire to drill through windows and bodywork.
(b) Tie something like wood block at both the end of steel wire.
Clues on: Stick adhesive tape on the bodywork at work
to prevent paintwork from scraping.
Notes: When separate window, do not damage
paintwork and interior and exterior trim board.
(c) Pull steel wire along front windscreen around, removal
agglutinant.
(d) Disassemble front windscreen.
Note: When cut front windscreen down, leave aggluti-
nant as much as possible on the bodywork.
15. Clean rear ventilation window assembly [68000103]
Use white gasoline to clean rear ventilation window around.
16. Assemble windscreen orientation plastic button
[68000064]
Assemble two orientation block on the rear windscreen as the

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Panel/combination instrument--panel
32. Disassemble lower panel assembly [68010005]
(a) Disassemble the joint of indoor temperature sensor.
(b) Disassemble machine cover locking pull cable with handle assembly.
(c) Disassemble six D bolts.
(d) Disassemble six fixing clamps and panel lower board.
33. Disassemble left storage box of lower panel [68010007]
34. Assemble upper panel assembly [68010004]
Assemble upper panel assembly with D bolt and two A screws.
D bolt: 18 N⋅m
35. Assemble CD machine assembly [67000126]
(a) Assemble pedal central ventilation hole assembly on CD machine assembly.
<D><D><D>
<D>
<D>
<D>
 345 

Anti-stealing and door lock--Electric door lock control system
Anti-stealing and door lock
Electric door lock control system
Position of parts (only for reference)
Inspection on automobile
1. Basic inspection for electric door locker.
(a) Press middle control switch to locker closing side, and check the all doors should be locked; then
press middle control switch to locker opening side, and check all doors should be opened.
(b) Insert key in door locker and turn it anticlockwise, and check all doors should be locked; then turn the
key clockwise, and check all doors should be opened.
(c) Check the keeping protection function of the key.
Note: When checking the keeping protection function of the key, it is necessary to open elec-
tric window at the side of driver to prevent its function from losing and lock the key in
automobile.
(1) Insert key in ignition switch.
(2) Open the door, and press middle control switch on the door at the side of driver to locker closing
side, at this time, door locker could not close.
(3) Open the door, and press locker button on the door at the side of driver to locker closing side, at
this time, door locker could not close.
(4) After pressing locker button upwards for over two seconds, and locking driver door; when driver
door is closed and key is not used to lock, check whether all doors could open automatically.
 355 
Door control switch of electric
window main switch assembly
(Used for handle operation)
Door control switch of left front
door locker assembly
(Used for key operation)
Door control light switch
Left rear door locker
assembly
Right front door
locker assembly
Right rear door
locker assembly

Anti-stealing and door lock--Electric door lock control system
3. Check panel junction box assembly.
(a) Check 25A DOOR fuse.
(b) Check conformity relay.
(1) Disassemble F, G, H and I joint on instrument junction
box.
(2) Check the voltage and conduction of every terminal of
joint. (d) Check security function:
(1) When closing all doors, open the driver window to operate door control switch out of automobile.
(2) Take down the key, open driver door, then close the door and lock (not use key). In this situation
above, check that door could not open locker even if door control switch (handle operation) is
pressed to locker opening side out of automobile.
(3) Take down the key, close and use the key to lock driver door. In this situation above, check that
door could not open locker even if door control switch (handle operation) is pressed to locker
opening side out of automobile.
(4) Take down the key, close and use remote control key to lock driver door. In this situation above,
check that door could not open locker even if door control switch (handle operation) is pressed to
locker closing side out of automobile (only applicable for the automobile equipping with remote
control door locker control system).
Hint:
zIn following situation, check whether security has been canceled.
zIgnition switch is turned to ON.
zUse key operation to open the driver door locker.
zAfter door locker is pressed to opening side by hand, door control switch (handle
operation) is pressed to locker opening side.
zUse remote control locker control to open the door (only applicable for the automobile
equipping with remote control door locker control system).
2. Electric window main switch assembly
Operate door control switch by hand to check its conduction.
 356 
Position of switch Terminal connected by avometerRegulated situation
LOCK 5-1 or 5-3Conduction
UNLOCK8-1 or 8-3↑

Anti-stealing and door lock--Electric door lock control system
 357 
Power supply (+) Power supply (+)
Power supply
(+)
1G2 in Power supply
(+)
1G2 out Power supply (-)
Power supply (+) Power supply (+) Power supply (+) Power supply (+)
Power supply
(+)Power supply
(+)Power supply
(-) Power supply
(+)
Power supply (+)
Power supply (+)
Grounding wire
Sunroof
Rain wiperBrake light Anti-steal
Power supply
(+)
InstrumentRear fog light

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Anti-stealing and door lock--Electric door lock control system
Inspection
1. Check driver sear door locker assembly.
(a) Liking that shown in figure, check the conduction of every
terminal of door key switch.
If the conduction does not accord with the regulation, change
the switch.
(b) Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change
the door locker assembly.
Open Close
Open Close
 359 
Position of switch Terminal connected by avometerRegulated situation
LOCK 2-4Conduction
OFF - Not conduction
UNLOCK 1-2-3 Conduction
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose

Anti-stealing and door lock--Electric door lock control system
2. Check front passenger seat door locker assembly
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
3. Check the left rear and right rear door locker assembly.
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
OpenClose
Open
Close
 360 
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose