roof GEELY FC 2008 Owner's Guide

Electric sunroof (optional)--Sunroof
7. Use screw driver (twisted by adhesive tape) to align
the sunroof driving pull cable with right mark.
8. Assemble sunroof shell body assembly.
(a) Bolt.
Torque: 5.5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
9. Assemble the glass of sunroof.
(a) Check the phase difference between sunroof waterproof ad-
hesive tape and top gasket.
Front end and rear end: 0±1.5mm
Rear corner: 0±1.5mm
0-1.5mm
(b) Adjustment
Use T25 planetary wrench to loosen the screw to adjust
the sunroof on correct position, then lock the screw.
10. Inspection for water leakage.
(a) After the adjustment, check whether the sunroof leaks water.
(b) If sunroof leaks water, adjust it again.
Assembly mark
 363 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof function
1. Inspection for sliding opening function.
(1) Turns ignition switch to ON, when spot contacting sunroof
switch keystroke 2, the sunroof will start automatic sliding
opening work, and it does not stop until it is at complete
opening state. If spot contacting it in running process, or
pressing keystroke 1 or 2 for long time, sunroof glass will
stop running immediately.
(2) Turns ignition switch to ON, when pressing keystroke 2 for
Sunroof system
Specification for sunroof function
1. Operation category
Spot contact: press the keystroke one time, then release immediately (the time is less than 0.3 seconds).
Long press: press the key stroke for long time (the time is more than 0.3).
2. Specification for function.
Anti-clamping function: spot contact the keystroke to make the sunroof could face 10 Kg resistance in the
process of closing from any position, at this time, electric motor turns oppositely, and the sunroof returns
turn-up or opening state.
Automatic closing function: when the key is pulled out from ignition locker, at this time, the sunroof is not
at closing state, it will close automatically in three seconds.
long time, the sunroof will start automatic sliding opening work, and it does not stop until it is at
complete opening state. If releasing keystroke 2 in running process, the sunroof glass will stop running
immediately.
2. Inspection for sliding closing function.
(1) Turns ignition switch to ON, if the sunroof is at opening state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically slide to closing state. If spot contacting it or pressing
keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at opening state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 1 in running
process, sunroof glass will stop running immediately.
3. Inspection for turn-up opening function
(1) Turns ignition switch to ON, if the sunroof is at closing state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically move to turn-up opening state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at closing state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to turn-up opening state. If releasing keystroke 1 in
running process, sunroof glass will stop running immediately.
4. Inspection for turn-up closing function
(1) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when spot contacting sunroof
switch keystroke 2, the sunroof will automatically move to closing state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when pressing sunroof switch
keystroke 2 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 2
in running process, sunroof glass will stop running immediately.
 364 
Front
Rear

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof

Engine cover/automobile door--Rear automobile doorRear automobile doorOverhaulHint:zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction..zOverhaul procedure for right side is same as the left side.1. Disassemble left rear door control panel assembly [68000176]Use screw driver to disassemble left rear door control panel assembly.Fixing
clasp
Fixing
clasp 373  2. Disassemble left rear door inner trim board assem-
bly [68010057](a) Disassemble three screws.
(b) Disconnect the fixing clamp, then pull inner trim board up-
wards to disassemble it.3. Disassemble left door inner handle assembly
[68010051]Disassemble inner handle and two pull cables from inner handle.4. Disassemble left rear door repairing hole cover.Disassemble repairing hole cover.5. Disassemble exterior seal tape of left rear door glass
[68000196]
6. Disassemble seal tape of left rear glass guide slot
[68000199](a) Disassemble seal tape of left rear glass guide slot.7. Disassemble left rear door window glass guide slot
assembly [68000187]Disassemble two bolts and comparting pillar of rear window.8. Disassemble left rear door triangle glass [68000181](a) Disassemble left rear door triangle glass.
Note: do not damage the glass.
(b) Disassemble corner window waterproof rubber from the glass.9. Disassemble left rear glass assembly [68000179]Hint: insert the cloth in the door steel board to prevent the glass from scratching.
(a) Drop the door glass.
(b) Incline door glass and disassemble the roller pole of lift from glass leading slot to disassemble door
glass.10. Disassemble left rear door lift assembly [67000124](a) Disassemble the joint.
(b) Disassemble four bolts and window lift.

Exterior/inner trim board--Inner trim board of top29. Disassemble the pothook of sun shade [68010086]Turn the pothook of sun shade to left for 90°, then disassemble
it.30. Disassemble fixing pedestal of rear window sun
blind.Use screw driver to turn the fixing pedestal of sun blind for 90°,
then disassemble it.31. Disassemble trim tape of top sunroof [67010010]
32. Disassemble inner trim board of top [68010035](a) Use screw driver to disassemble inner trim board of top.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Disassemble three fixing clamps and inner trim board of
top.
(c) Take out inner trim board of top from rear door.33. Assemble inner trim board of top [68010035](a) Liking that shown in figure, align the mark, then fix the wir-
ing harness of top with adhesive tape.
(b) Use three fixing clamps to assemble inner trim board of top.34. Assemble the pothook of sun shade [68010086]Turn the pothook of sun shade to make fixing claw proturde,
then assemble sun shade.35. Assemble rear row chair left backrest assembly
[68010078]
36. Assemble rear row chair right backrest assembly
[68010079]
37. Assemble rear row chair backrest assembly
[68010076]Fixing
clamp
Adhesive
tape393

Electric sunroof Electric chairElectrical schematic diagram--Electric sunroof Electric chair 399