four wheel drive GEELY FC 2008 Workshop Manual

Drive shaft--Left rear shaft hub and bearing assemblyLeft rear shaft hub and bearing assemblyChangeHint: changing procedure for right side is same as left side.129 6. Disassemble rear wheel speed sensor assembly (equipping with ABS) [67000023]
(referring to page 52)
7. Assemble rear wheel speed sensor assembly (equipping with ABS) [67000023] (referring
to page 52) 1. Disassemble rear wheels.
2. Disassemble rear brake caliper assembleDisassemble two bolts and take down brake caliper.3. Disassemble the wiring harness of rear wheel speed
sensor (equipping with ABS).Disassemble the joint of rear wheel speed sensor.4. Disassemble left rear brake assembly [64000137]
5. Disassemble left rear shaft hub and bearing
assembly.Disassemble four bolts, then take down lower shaft hub and
bearing assembly.8. Assemble left rear shaft hub and bearing assemblyUse four bolts to assemble left rear shaft hub and bearing
assembly9. Assemble wiring harness of rear wheel speed sen-
sor (equipping with ABS).Connect the joint of rear wheel speed sensor.

Supplemental restraint system--Scrap treatment for safety airbag
b. Use maintenance electric wire used for automobile to fix
safety airbag module at the side of driver on wheel.
Section area of nude wire part of wiring harness is more
than 2 mm
2. If the wiring harness is too thin, it might
break for the shake when airbag explodes. This is very
dangerous.
c. Use four wiring harnesses, and the wiring harness should
twist the fixed bolts and small bracket of airbag assem-
bly twice at least. Tighten the wiring harness twisted to
avoid them loosen, if wiring harness loosen, they might
incur airbag assembly loosens for shake when airbag
explodes. This is very dangerous.
d. Place the airbag module upwards, and bind the wiring
harnesses at the two sides of airbag module in wheel
tightly. After twisting the tyre twice with the wiring har-
ness twisted on middle small bracket, bind it on tyre.
After twisting the tyre twice with the wiring harness
twisted on left and right small bracket, bind it on tyre.
Adjust the fixed position of airbag module to make the
joint hang in the wheel hub hole of wheel. Then fix the
wiring harness getting through the center of left and right
small bracket on tyre to prevent the module from shak-
ing left and right, and the wiring harness twisted on bolts
of small bracket is fixed on tyre to prevent airbag mod-
ule from shaking front and back.
(4) Place the wheel on flat ground, and connect one end of
wiring harness used for unfolding with airbag short wiring
harness, and connect the other end with short circuit. The
terminal end of unfolding wiring harness is 10m apart from
wheel of fixed airbag at least.
 268 
Safety airbag assembly
Wiring harness for explosion
Tyre
(over five)

Panel/combination instrument-- panel
3 Fixing clamp
4 Fixing clasp
5. Disassemble safety airbag assembly at the side of
driver [67010011] (Referring to page 261)
6. Disassemble steering wheel assembly [67010001]
(referring to page 194)
7. Disassemble Combination instrument cover
[68000077]
(a) Disassemble fixing clamp.
(b) Use screw driver to unclench three fixing clamps and four
fixing clasps, then disassemble Combination instrument.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
8. Disassemble Combination instrument assembly
[67000081]
(a) Disassemble A screw.
(b) Liking that shown in figure, unclench two fixing clamps.
(c) Disassemble the joint, then disassemble Combination in-
strument assembly.
9. Disassemble panel left ventilation hole assembly
[68010010]
Use disassembling tool for trim tape to disassemble panel left
ventilation hole assembly.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
10. Disassemble panel right ventilation hole assembly
[68010011]
11. Disassemble front ashtray
12. Disassemble shift organization trim board assem-
bly [68000076]
(a) Use screw driver to unclench six fixing clamps.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble the joint, then disassemble shift organization
trimmain board.
 341 
4 Fixing clasp
6 Fixing clamp

Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of rear bumper on page 381.
Exterior/inner trim board--Rear bumper
 382  1. Disassemble trunk carpet assembly [68000114]
2. Disassemble rear trim board of trunk [68000118]
(a) Use two fixing clasps.
(b) Use disassembling tool for trim tape to disassemble rear
trim board of trunk.
3. Disassemble left decoration of trunk [68000112]
(a) Use disassembling tool for fixing clamp to disassemble
fixing clamp and a part of left decoration of trunk.
Hint:
Disassemble the fixing clasp and left decoration of trunk in the scope of screw cap used for
fixing rear bumper and trunk which could be disassembled.
4. Disassemble right decoration of trunk [68000113]
5. Disassemble mudguard of left rear wheel [68000223]
(a) Disassemble two screws and mudguard of left rear wheel.
6. Disassemble mudguard of right rear wheel [68000224]
7. Disassemble trim board of left rear wheel [68000230]
(a) Use screw driver to disassemble fixing clasp from rear bumper.
(b) Use disassembling tool for fixing clasp to disassemble fix-
ing clasp.
(c) Disassemble trim board of left rear wheel.
Hint: Disassemble trim board of left rear wheel in the
scope of screw used for fixing rear bumper which could
be disassembled.
8. Disassemble trim board of right rear wheel [68000231]
9. Disassemble rear bumper [68000012]
(a) Use screw driver to disassemble two fixing clasps.
(b) Disassemble four screw caps and two screws.
(c) Disassemble fixing clasp and rear bumper.
(d) Equipping with radar probe head: disassemble four joints of
radar probe head.
10. Disassemble reversing radar probe head assembly.
(a) Disassemble fixing pedestal of radar probe and radar probe.
11. Disassemble left rear fog light assembly [67000100]
(a) Disassemble fixing nut and left rear fog light assembly.
12. Disassemble right rear fog light assembly [67000101]