fuel GENESIS G70 2023 Service Manual

Maintenance9-34
TIRES AND WHEELS
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:

[ Inspect your tires monthly for
proper inflation as well as wear
and damage.

[ The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.

[ Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.

[ Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.

[ ALWAYS replace tires with the
same size, type, construction and
tread pattern as each tire that
was originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.
Tire Care
For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended
tire inflation pressures and stay
within the load limits and weight
distribution recommended for your
vehicle.
OIK087002L
All specifications (sizes and
pressures) can be found on a label
attached to the driver’s side center
pillar.
Recommended Cold Tire
Inflation Pressures
All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold tires” means the
vehicle has not been driven for at
least three hours or driven less than
one mile (1.6 km).
Warm tires normally exceed
recommended cold tire pressures
by 4 to 6 psi (28 to 41 kPa). Do not
release air from warm tires to adjust
the pressure or the tires will be
under-inflated. For recommended
inflation pressure, refer to “Tire and
Wheels” section in chapter 2.

09
9-35
WARNING
Recommended pressures must be
maintained for the best ride, vehicle
handling, and minimum tire wear.
Over-inflation or under-inflation
can reduce tire life, adversely
affect vehicle handling, and lead to
sudden tire failure that could result
in loss of vehicle control resulting in
an accident.
Severe under-inflation can lead
to severe heat build-up, causing
blowouts, tread separation and
other tire failures that can result in
the loss of vehicle control resulting
in an accident. This risk is much
higher on hot days and when
driving for long periods at high
speeds.
CAUTION

[Under-inflation results in
excessive wear, poor handling
and reduced fuel economy.
Wheel deformation is also
possible. Keep your tire pressures
at the proper levels. If a tire
frequently needs refilling, have it
checked by an authorized retailer
of Genesis Branded products.

[ Over-inflation produces a harsh
ride, excessive wear at the center
of the tire tread, and a greater
possibility of damage from road
hazards.
Check tire Inflation Pressure
Check your tires including the spare
tire once a month or more.
How to check
Use a good quality tire pressure
gauge to check tire pressure. You
can not tell if your tires are properly
inflated simply by looking at them.
Radial tires may look properly
inflated even when they are under-
inflated.
Remove the valve cap from the tire
valve stem. Press the tire gauge
firmly onto the valve to get a
pressure measurement. If the cold
tire inflation pressure matches the
recommended pressure on the tire
and loading information label, no
further adjustment is necessary. If
the pressure is low, add air until you
reach the recommended pressure.
Make sure to put the valve caps
back on the valve stems. Without
the valve cap, dirt or moisture could
get into the valve core and cause
air leakage. If a valve cap is missing,
install a new one as soon as possible.
If you overfill the tire, release air by
pushing on the metal stem in the
center of the tire valve. Recheck the
tire pressure with the tire gauge. Be
sure to put the valve caps back on
the valve stems. Without the valve
cap, dirt or moisture could get into
the valve core and cause air leakage.
If a valve cap is missing, install a new
one as soon as possible.

Maintenance9-42
WARNING
The temperature grade for this tire is
established for a tire that is properly
inflated and not overloaded.
Excessive speed, under-inflation,
over-inflation, or excessive loading,
either separately or in combination,
can cause heat build-up and
possible sudden tire failure. This
may cause loss of vehicle control
resulting in an accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim. Bias ply tire
A pneumatic tire in which the plies are
laid at alternate angles less than 90
degrees to the centerline of the tread.
Cold tire pressure
The amount of air pressure in a tire,
measured in pounds per square inch
(psi) or kilopascals (kPa) before a tire
has built up heat from driving.
Curb weight
This means the weight of a motor
vehicle with standard and optional
equipment including the maximum
capacity of fuel, oil and coolant, but
without passengers and cargo.
DOT markings
A code molded into the sidewall
of a tire signifying that the tire
is in compliance with the U.S.
Department of Transportation motor
vehicle safety standards. The DOT
code includes the Tire Identification
Number (TIN), an alphanumeric
designator which can also identify
the tire manufacturer, production
plant, brand and date of production.
GVWR
Gross Vehicle Weight Rating
GAWR FRT
Gross Axle Weight Rating for the
Front Axle.
GAWR RR
Gross Axle Weight Rating for the
Rear axle.

Maintenance9-52
Fuse Name Fuse Rating Circuit Protected
DOOR LOCK 20
A Door Lock Relay, Door Unlock Relay, Dead Lock Relay
SEAT HEATER 25AFront Air Ventilation Seat Control Module
Front Seat Warmer Control Module
TRUNK 10A Trunk Lid Relay, Fuel Lid Relay, Crash Pad Switch
IBU2 10A IBU, Rain Sensor
AIR BAG2 15A SRS Control Module
POWER OUTLET1 20A Front Power Outlet
MODULE8 10A Cooling Fan Controller (BLDC Motor)
MODULE7 10ADosing Control Module, AWD ECM, Active Air Flap LH,
ECS Unit, Front View Camera, Console Switch, Crash
Pad Switch, IBU, Console Switch, Front View Camera,
Front Wireless Charger, Steering Tilt & Telescopic
Module, Surround View Monitor ECU, Electronic Control
Engine Mounting Module, Steering Angle Sensor
POWER HANDLE 15A Steering Tilt & Telescopic Module
MODULE9 10A Driver Air Lumbar Control Unit
MODULE1 10AData Link Connector, Console Switch, Hazard
Switch, Electronic Control Engine Mounting Module
CHARGER 10A Front/Rear USB Charger, Front Tray USB Charger
MODULE5 10AA/C Control Module, A/C Switch, A/V & Navigation
Head Unit, Low DC-DC Converter (Audio/AMP), Electro
Chromic Mirror, AMP, Emergency Module, Driver IMS
Control Module, Front Air Ventilation Seat Control
Module, Data Link Connector, Front/Rear Seat Warmer
Control Module, IFS Module
SUNROOF 20A Sunroof Control Unit (Glass)
PASSENGER P/ WINDOW 25APassenger Safety Power Window Module, Rear Power
Window Switch RH, Rear Safety Power Window Module
RH
POWER
OUTLET2 20A [5DR] Rear Power Outlet

09
9-57
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ESC3 10
A ESP Control Module
ECU3 10A ECM
ECU2 15A ECM
HORN 20A Horn Relay
WIPER1 30A Wiper Power Relay
TCU2 15A P/N Relay, TCM
SENSOR4 10AElectronic Oil Pump Module, Brake Vacuum Switch, E/R
Junction Block (RLY.1 (Brake Vacuum Relay))
TCU1 20A TCM
WIPER2 10A IBU, ECM
SENSOR1 15ARear Sub Junction Block (Fuel Pump Relay),
[D4HB] Rail Pressure Regulating Valve, DieseL Junction
Block (RLY.1 (Fuel Filter Heater Relay))
SENSOR5 20A[G4KL] Ignition Coil #1/#2/#3/#4
[G6DP] Ignition Coil #1/#2/#3/#4/#5/#6
[D4HB] Electronic Water Pump
MODULE 10A Active Air Flap LH
SENSOR1 10A[D4HB] Glow Relay Unit, Fuel Heater & Water Separator
Sensor
ECU1 20A ECM
SENSOR3 15A[G4KL] Oxygen Sensor (Up/Down)
[G6DP] Oxygen Sensor #1/#2/#3/#4
[D4HB] Lambda Sensor #1/#2, Electronic VGT Actuator,
Fuel Metering Unit, EGR Cooing Bypass Solenoid
Vlave, PTC Heater, Mid Nox Sensor, PM Sensor,
Rear Nox Sensor

Maintenance9-60
Rear fuse box panel
Fuse Name Fuse Rating Circuit Protected
DCU2 15A Dosing Control Module
DCU3
15A Dosing Control Module
REAR WIPER 15A Wipre RR Relay, Rear Wiper Motor ECS 15A ECS Unit
POWER TRUNK 30A Power Trunk Module, Power Tailgate Unit DCU1 15A Dosing Control Module
FUEL PUMP 20A Fuel Pump Relay
HEAT MIRROR 10A A/C Switch, Driver/Passenger Power Outside Mirror AMP2 25A AMP
REAR S/HEAT 20A Rear Seat Warmer Control Module AMP1 30A[W/O ISG] Fuse - F9
[With ISG] Low DC-DC Converter (AMP)
IG1 15A PCB Block (IG1 Relay)
ACC 30A ICU Junction Block (Fuse - F32, F40, F54)
B+1 40AICU Junction Block
(IPS5, IPS6, IPS7, IPS8, IPS9, IPS10, Fuse - F20, 30F)
B+2 40A ICU Junction Block (IPS1, IPS2, Fuse - F15, F39)
REAR HEATED 30A Rear Heated Relay

09
9-71
Bright-metal maintenance

[To remove road tar and insects, use
a tar remover, not a scraper or other
sharp object.

[ To protect the surfaces of brightmetal
parts from corrosion, apply a coating
of wax or chrome preservative and rub
to a high luster.

[ During winter weather or in coastal
areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, accelerated
rusting can occur on underbody parts
such as the fuel lines, frame, floor pan
and exhaust system, even though they
have been treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter.
Pay special attention to these areas
because it will do more harm than good
if the road grime becomes wet without
removing it. The lower edges of doors,
rocker panels, and frame members have
drain holes that should not be allowed
to clog with dirt; trapped water in these
areas can cause rusting.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
while maintaining a slow forward
speed.
Aluminum wheel maintenance
The aluminum wheels are coated with a
clear protective finish.

[Do not use abrasive cleaner, polishing
compound, solvent, or wire brushes
on aluminum wheels.

[ Clean the wheel when it has cooled.

[ Use only a mild soap or neutral
detergent, and rinse thoroughly with
water. Also, clean the wheels after
driving on salted roads.

[ Do not wash the wheels with high-
speed car wash brushes.

[ Do not use any cleaners containing
acid or alkaline detergents.

09
9-77
EMISSION CONTROL SYSTEM
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Owner’s
Handbook & Warranty Information
booklet in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
applicable emission regulations. There
are three emission control systems, as
follows.
(1) Crankcase emission control system
(2) Evaporative emission control system
(3) Exhaust emission control system
In order to ensure the proper function
of the emission control systems, it
is recommended that you have your
vehicle inspected and maintained by an
authorized retailer of Genesis Branded
products in accordance with the
maintenance schedule in this manual.
NOTICE
For the Inspection and Maintenance
Test (with Electronic Stability Control
(ESC) system)

[ To prevent the vehicle from misfiring
during dynamometer testing, turn
the Electronic Stability Control
(ESC) system off by pressing the ESC
switch (ESC OFF light illuminated).

[ After dynamometer testing is
completed, turn the ESC system back
on by pressing the ESC switch again.
1. Crankcase Emission Control
System
The positive crankcase ventilation system
is employed to prevent air pollution
caused by blow-by gases being emitted
from the crankcase. This system supplies
fresh filtered air to the crankcase through
the air intake hose. Inside the crankcase,
the fresh air mixes with blow-by gases,
which then pass through the PCV valve
into the induction system.
2. Evaporative Emission Control System Including Onboard
Refueling Vapor Recovery
(ORVR)
The Evaporative Emission Control System
is designed to prevent fuel vapors from
escaping into the atmosphere. The
ORVR system is designed to allow the
vapors from the fuel tank to be loaded
into a canister while refueling at the gas
station, preventing the escape of fuel
vapors into the atmosphere.
Canister
Fuel vapors generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in the
canister are drawn into the surge tank
through the purge control solenoid valve.
Purge Control Solenoid Valve (PCSV)
The purge control solenoid valve
is controlled by the Engine Control
Module (ECM); when the engine coolant
temperature is low during idling, the
PCSV closes so that evaporated fuel
is not taken into the engine. After the
engine warms up during ordinary driving,
the PCSV opens to introduce evaporated
fuel to the engine.

09
9-79
Operating precautions for catalytic
converters
WARNING
The exhaust system and catalytic
system are very hot while the engine is
running or immediately after the engine
is turned off. To avoid SERIOUS INJURY
or DEATH:

[Do not park, idle, or drive the vehicle
over or near flammable objects, such
as grass, vegetation, paper, leaves,
etc. A hot exhaust system can ignite
flammable items under your vehicle.

[ Keep away from the exhaust system
and catalytic converter or you may
get burned.
Also, do not remove the heat sink
around the exhaust system, do not
seal the bottom of the vehicle, and
do not coat the vehicle for corrosion
control. It may present a fire risk
under certain conditions.
Your vehicle is equipped with a catalytic
converter emission control device.
To prevent damage to the catalytic
converter and to your vehicle, take the
following precautions:

[ Use only UNLEADED FUEL for
gasoline engines.

[ Do not operate the vehicle when
there are signs of engine malfunction,
such as misfire or a noticeable loss of
performance.

[ Do not misuse or abuse the engine.
Examples of misuse are coasting with
the engine off and descending steep
grades in gear with the engine off.

[ Do not operate the engine at high idle
speed for extended periods
(5 minutes or more).

[Do not modify or tamper with any
part of the engine or emission
control system. All inspections and
adjustments must be made by an
authorized retailer of Genesis Branded
products.

[ Avoid driving with an extremely low
fuel level.
Running out of fuel could cause the
engine to misfire, damaging the
catalytic converter.
CALIFORNIA PERCHLORATE
NOTICE
Perchlorate Material-special handling
may apply, See: https://dtsc.ca.gov/
perchlorate
Notice to California Vehicle Dismantlers:
Perchlorate containing materials, such as
air bag inflators, seatbelt pretensioners
and keyless remote entry batteries, must
be disposed of according to Title 22
California Code of Regulations Section
67384.10 (a).

IndexI-6
F
Forward Collision–Avoidance Assist (FCA) (Sensor fusion) ............................... 7-2
Forward Collision-Avoidance Assist Malfunction and Limitations ................ 7-10
Forward Collision-Avoidance Assist Operation ................................................ 7-5
Forward Collision-Avoidance Assist Settings ................................................... 7-3
Forward/Reverse Parking Distance Warning (PDW) ....................................... 7-109
Forward/Reverse Parking Distance Warning Malfunction and Limitations . 7-112
Forward/Reverse Parking Distance Warning Operation ............................... 7-110
Forward/Reverse Parking Distance Warning Settings .................................. 7-109
Fuel Requirements ........................................................................\
......................... 1-5
Fuses ........................................................................\
............................................ 9-47
Engine Compartment Panel Fuse Replacement .............................................. 9-49
Fuse/Relay Panel Description ........................................................................\
. 9-50
Instrument Panel Fuse Replacement ............................................................... 9-48
G
Genesis Customer Care........................................................................\
.................. 1-2
Genesis Digital Key ........................................................................\
..................... 5-13
Digital Key (Card Key) ........................................................................\
........... 5-19
Digital Key (Smart Phone) ........................................................................\
...... 5-13
Limitations of the System ........................................................................\
....... 5-25
Personalized Profile and Vehicle Settings ....................................................... 5-22
Used Vehicle/Digital Key Maintenance .......................................................... 5-25
Guide to Genesis Parts ........................................................................\
................... 1-3
H
Hazard Warning Flasher ........................................................................\
................ 8-2
Head-Up Display (HUD) ........................................................................\
............. 5-76
Head-Up Display Information.............................................\
............................ 5-76
Head-Up Display Settings ........................................................................\
....... 5-76
Precautions While Using the Head-Up Display .............................................. 5-77
High Beam Assist (HBA) ........................................................................\
............ 5-84
High Beam Assist Malfunction and Limitations ............................................. 5-85
High Beam Assist Operation ........................................................................\
... 5-85
High Beam Assist Settings ........................................................................\
...... 5-84