load capacity GENESIS G80 2021 Owner's Manual
Page 304 of 604
06
6-39
Emergency Precautions
Tires
When replacing tires, be sure to equip 
all four tires with the same size, type, 
tread pattern, brand and load-carrying 
capacity.
 WARNING
Do not use tire and wheel with different 
size and type from the one originally 
installed on your vehicle. It can affect 
the safety and performance of your 
vehicle, which could lead to steering 
failure or rollover causing serious injury.
In an emergency situation, a compact 
spare tire may be used. But, do not use 
the compact spare tire continuously. 
Repair or replace the original tire as 
soon as possible to avoid failure of the 
differential or AWD system.
 WARNING
ORG3060019
Never start or run the engine while a 
vehicle is raised on a jack. The vehicle 
can slip or roll off of a jack causing 
serious injury or death to you or those 
nearby.
Towing
AWD vehicles must be towed with 
a wheel lift and dollies or flatbed 
equipment with all the wheels off the 
ground. For more details, refer to 
"Towing" section in chapter 8.
Vehicle inspection
• If the vehicle needs to be operated on 
a vehicle lift do not attempt to stop 
any of the four wheels from turning. 
This could damage the AWD system.
• Never engage the parking brake while 
running the engine on a car lift. This 
may damage the AWD system.   
Page 324 of 604
06
6-59
The Loading Information Label
„„Type A
ORG3080040N
„„Type B
ORG3080042N
„„Type C
ORG3080041N
The label located on the driver’s door 
sill gives the original tire size, cold 
tire pressures recommended for your 
vehicle, the number of people that can 
be in your vehicle and vehicle capacity 
weight.
Vehicle capacity weight
882 lbs. (400 kg)
Vehicle capacity weight is the maximum 
combined weight of occupants and 
cargo. If your vehicle is equipped with a 
trailer, the combined weight includes the 
tongue load.
Seating capacity
Total :  5 persons (Front seat : 2 persons, Rear seat : 3 persons)
Seating capacity is the maximum 
number of occupants including a driver, 
your vehicle may carry. However, the 
seating capacity may be reduced based 
upon the weight of all of the occupants, 
and the weight of the cargo being carried 
or towed. Do not overload the vehicle as 
there is a limit to the total weight, or load 
limit including occupants and cargo, the 
vehicle can carry.
Towing capacity
We do not recommend using this vehicle 
for trailer towing.
Cargo capacity
The cargo capacity of your vehicle will 
increase or decrease depending on the 
weight and the number of occupants 
and the tongue load, if your vehicle is 
equipped with a trailer.   
Page 325 of 604
Driving Your Vehicle
6-60
Steps for determining correct load 
limit
1. Locate the statement "The combined 
weight of occupants and cargo should 
never exceed XXX kg or XXX lbs." on 
your vehicle's placard.
2. Determine the combined weight of 
the driver and passengers that will be 
riding in your vehicle.
3. Subtract the combined weight of the 
driver and passengers from XXX kg or 
XXX lbs.
4. The resulting figure equals the 
available amount of cargo and 
luggage load capacity. For example, 
if the "XXX" amount equals 1400 
lbs. and there will be five 150 lb 
passengers in your vehicle, the 
amount of available cargo and 
luggage load capacity is 650 lbs. 
(1400 - 750 (5 x 150) = 650 lbs.)
5. Determine the combined weight of 
luggage and cargo being loaded on 
the vehicle. That weight may not 
safely exceed the available cargo and 
luggage load capacity calculated in 
Step 4.
6. If your vehicle will be towing a 
trailer, load from your trailer will be 
transferred to your vehicle. Consult 
this manual to determine how this 
reduces the available cargo and 
luggage load capacity of your vehicle.
 WARNING
Do not overload the vehicle as there 
is a limit to the total weight, or load 
limit, including occupants and cargo, 
the vehicle can carry. Overloading can 
shorten the life of the vehicle. If the 
GVWR or the GAWR is exceeded, parts 
on the vehicle can break, and it can 
change the handling of your vehicle. 
These could cause you to lose control 
and result in an accident.   
Page 327 of 604
Driving Your Vehicle
6-62
Certification label
OBH059070
The certification label is located on the 
driver's door sill at the center pillar and 
shows the maximum allowable weight of 
the fully loaded vehicle. This is called the 
GVWR (Gross Vehicle Weight Rating). The 
GVWR includes the weight of the vehicle, 
all occupants, fuel and cargo.
This label also tells you the maximum 
weight that can be supported by the 
front and rear axles, called Gross Axle 
Weight Rating (GAWR).
The total weight of the vehicle, including 
all occupants, accessories, cargo, and 
trailer tongue load must not exceed the 
Gross Vehicle Weight Rating (GVWR) or 
the Gross Axle Weight Rating (GAWR). 
To find out the actual loads on your front 
and rear axles, you need to go to a weigh 
station and weigh your vehicle. Be sure 
to spread out your load equally on both 
sides of the centerline.
 WARNING
Overloading
• Never exceed the GVWR for your 
vehicle, the GAWR for either the front 
or rear axle and vehicle capacity 
weight. Exceeding these ratings 
can affect your vehicle's handling 
and braking ability, and cause an 
accident.
• Do not overload your vehicle. 
Overloading your vehicle can cause 
heat buildup in your vehicle's tires 
and possible tire failure, increased 
stopping distances and poor vehicle 
handling-all of which may result in a 
crash.
NOTICE
Overloading your vehicle may cause 
damage. Repairs would not be covered 
by your warranty. Do not overload your 
vehicle.   
Page 509 of 604
08
8-17
NOTICE
Check the tire pressure as soon as 
possible after installing a spare tire. 
Adjust it to the recommended pressure.
 CAUTION
Your vehicle has metric threads on the 
studs and wheel bolts. Make certain 
during tire changing that the same bolts 
that were removed are reinstalled. If 
you have to replace your wheel bolts 
make sure they have metric threads to 
avoid damaging the studs and ensure 
the wheel is properly secured to the 
hub. Consult an authorized retailer 
of Genesis Branded products for 
assistance.
If any of the equipment such as the jack, 
wheel bolts, studs, or other equipment 
is damaged or in poor condition, do not 
attempt to change the tire and call for 
assistance.
Use of compact spare tires
Compact spare tires are designed for 
emergency use only. Drive carefully on 
the compact spare tire and always follow 
the safety precautions.
 WARNING
To prevent compact spare tire failure 
and loss of control possibly resulting in 
an accident:
• Use the compact spare tire only in an 
emergency.
• NEVER operate your vehicle over  
50 mph (80 km/h).
• Do not exceed the vehicle’s 
maximum load rating or the load 
carrying capacity shown on the 
sidewall of the compact spare tire.
• Do not use the compact spare tire 
continuously. Repair or replace the 
original tire as soon as possible to 
avoid failure of the compact spare 
tire.   
Page 553 of 604
Maintenance
9-38
 WARNING
The temperature grade for this tire is 
established for a tire that is properly 
inflated and not overloaded. 
Excessive speed, under-inflation, 
over-inflation, or excessive loading, 
either separately or in combination, 
can cause heat build-up and 
possible sudden tire failure. This 
may cause loss of vehicle control 
resulting in an accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire 
pressing outward on the tire. Air 
pressure is expressed in pounds per 
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight 
of optional accessories. Some 
examples of optional accessories 
are automatic transmission, power 
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to 
its width.
Belt
A rubber coated layer of cords that 
is located between the plies and the 
tread. Cords may be made from steel 
or other reinforcing materials.
Bead
The tire bead contains steel wires 
wrapped by steel cords that hold the 
tire onto the rim.Bias ply tire
A pneumatic tire in which the plies are 
laid at alternate angles less than 90 
degrees to the centerline of the tread.
Cold tire pressure
The amount of air pressure in a tire, 
measured in pounds per square inch 
(psi) or kilopascals (kPa) before a tire 
has built up heat from driving.
Curb weight
This means the weight of a motor 
vehicle with standard and optional 
equipment including the maximum 
capacity of fuel, oil and coolant, but 
without passengers and cargo.
DOT markings
A code molded into the sidewall 
of a tire signifying that the tire 
is in compliance with the U.S. 
Department of Transportation motor 
vehicle safety standards. The DOT 
code includes the Tire Identification 
Number (TIN), an alphanumeric 
designator which can also identify 
the tire manufacturer, production 
plant, brand and date of production.
GVWR
Gross Vehicle Weight Rating
GAWR FRT
Gross Axle Weight Rating for the 
Front Axle.
GAWR RR
Gross Axle Weight Rating for the 
Rear axle.    
Page 554 of 604
09
9-39
Intended outboard sidewall
The side of an asymmetrical tire, 
that must always face outward when 
mounted on a vehicle.
Kilopascal (kPa)
The metric unit for air pressure.
Light Truck (LT) tire
A tire designated by its manufacturer 
as primarily intended for use on 
lightweight trucks or multipurpose 
passenger vehicles.
Load ratings
The maximum load that a tire is rated 
to carry for a given inflation pressure.
Load index
An assigned number ranging from 1 
to 279 that corresponds to the load 
carrying capacity of a tire.
Maximum inflation pressure
The maximum air pressure to which 
a cold tire may be inflated. The 
maximum air pressure is molded 
onto the sidewall.
Maximum load rating
The load rating for a tire at the 
maximum permissible inflation 
pressure for that tire.Maximum loaded vehicle weight
The sum of curb weight; accessory 
weight; vehicle capacity weight; and 
production options weight.
Normal occupant weight
The number of occupants a vehicle 
is designed to seat multiplied by 150 
pounds (68 kg).
Occupant distribution
Designated seating positions.
Outward facing sidewall
An asymmetrical tire has a particular 
side that faces outward when 
mounted on a vehicle. The outward 
facing sidewall bears white lettering 
or bears manufacturer, brand, and/or 
model name molding that is higher 
or deeper than the same moldings 
on the inner facing sidewall.
Passenger (P-Metric) tire
A tire used on passenger cars 
and some light duty trucks and 
multipurpose vehicles.
Ply
A layer of rubber-coated parallel 
cords.   
Page 555 of 604
Maintenance
9-40
Pneumatic tire
A mechanical device made of rubber, 
chemicals, fabric and steel or other 
materials, that, when mounted on 
an automotive wheel provides the 
traction and contains the gas or fluid 
that sustains the load.
Pneumatic options weight
The combined weight of installed 
regular production options weighing 
over 5 lb. (2.3 kg) in excess of the 
standard items which they replace, 
not previously considered in 
curb weight or accessory weight, 
including heavy duty breaks, ride 
levelers, roof rack, heavy duty 
battery, and special trim.
Recommended inflation pressure
Vehicle manufacturer’s 
recommended tire inflation pressure 
as shown on the tire placard.
Radial ply tire
A pneumatic tire in which the ply 
cords that extend to the beads are 
laid at 90 degrees to the centerline 
of the tread.
Rim
A metal support for a tire and upon 
which the tire beads are seated.
Sidewall
The portion of a tire between the 
tread and the bead.
Speed rating
An alphanumeric code assigned to a 
tire indicating the maximum speed 
at which a tire can operate.Traction
The friction between the tire and 
the road surface. The amount of grip 
provided.
Tread
The portion of a tire that comes into 
contact with the road.
Treadwear indicators
Narrow bands, sometimes called 
“wear bars”, that show across the 
tread of a tire when only 1/16 inch of 
tread remains.
UTQGS
Uniform Tire Quality Grading 
Standards is a tire information 
system that provides consumers 
with ratings for a tire’s traction, 
temperature and treadwear. 
Ratings are determined by tire 
manufacturers using government 
testing procedures. The ratings are 
molded into the sidewall of the tire.
Vehicle capacity weight
The number of designated seating 
positions multiplied by 150 lbs. (68 
kg) plus the rated cargo and luggage 
load.
Vehicle maximum load on the tire
Load on an individual tire due to curb 
and accessory weight plus maximum 
occupant and cargo weight.
Vehicle normal load on the tire
Load on an individual tire that is 
determined by distributing to each 
axle its share of the curb weight, 
accessory weight, and normal 
occupant weight and dividing by 2.    
Page 556 of 604
09
9-41
Vehicle placard
A label permanently attached 
to a vehicle showing the 
original equipment tire size and 
recommended inflation pressure.
All Season Tires
Genesis Branded Vehicle specifies 
all season tires on some models to 
provide good performance for use 
all year round, including snowy and 
icy road conditions. All season tires 
are identified by ALL SEASON and/
or M+S (Mud and Snow) on the tire 
sidewall. Snow tires have better 
snow traction than all season tires 
and may be more appropriate in 
some areas.
Summer Tires
Genesis Branded Vehicle specifies 
summer tires on some models to 
provide superior performance on dry 
roads. Summer tire performance is 
substantially reduced in snow and 
ice. Summer tires do not have the 
tire traction rating M+S (Mud and 
Snow) on the tire side wall. If you 
plan to operate your vehicle in snowy 
or icy conditions, Genesis Branded 
Vehicle recommends the use of 
snow tires or all season tires on all 
four wheels.
Snow Tires
If you equip your car with snow 
tires, they should be the same size 
and have the same load capacity as 
the original tires. Snow tires should 
be installed on all four wheels; 
otherwise, poor handling may result. 
Snow tires should carry 4 psi (28 kPa) 
more air pressure than the pressure 
recommended for the standard 
tires on the tire label on the driver’s 
side of the center pillar, or up to the 
maximum pressure shown on the tire 
sidewall, whichever is less. Do not 
drive faster than 75 mph (120 km/h) 
when your vehicle is equipped with 
snow tires.
Radial-Ply Tires
Radial-ply tires provide improved 
tread life, road hazard resistance 
and smoother high speed ride. The 
radial-ply tires used on this vehicle 
are of belted construction, and are 
selected to complement the ride 
and handling characteristics of 
your vehicle. Radial-ply tires have 
the same load carrying capacity, 
as bias-ply or bias belted tires of 
the same size, and use the same 
recommended inflation pressure. 
Mixing of radial-ply tires with 
bias-ply or bias belted tires is not 
recommended. Any combinations of 
radial-ply and bias-ply or bias belted 
tires when used on the same vehicle 
will seriously deteriorate vehicle 
handling. The best rule to follow 
is: Identical pairs of radial-ply tires 
should always be used as a set for 
the front tires and a set for the rear 
tires.   
Page 558 of 604
09
9-43
■ Blade type
■ Cartridge type
■  Multi type
■  Midi type Normal
Blown
Normal Blown
Normal Blown
Normal Blown
OCK077071
A vehicle’s electrical system is protected 
from electrical overload damage by 
fuses.
This vehicle has 5 fuse panels, one 
located in the driver’s side panel bolster, 
the other in the engine compartment.
If any of your vehicle’s lights, 
accessories, or controls do not work, 
check the appropriate circuit fuse. If a 
fuse has blown, the element inside the 
fuse will be melted or broken.
If the electrical system does not work, 
first check the driver’s side fuse panel. 
Before replacing a blown fuse, turn the 
engine and all switches off, and then 
disconnect the negative battery cable. 
Always replace a blown fuse with one of 
the same rating.
If the replacement fuse blows, this 
indicates an electrical problem. 
Avoid using the system involved and 
immediately consult an authorized 
retailer of Genesis Branded products.
 WARNING
NEVER replace a fuse with anything but 
another fuse of the same rating.
• A higher capacity fuse could cause 
damage and possibly cause a fire.
• Do not install a wire or aluminum 
foil instead of the proper fuse - 
even as a temporary repair. It may 
cause extensive wiring damage and 
possibly a fire.
NOTICE
Do not use a screwdriver or any other 
metal object to remove fuses because 
it may cause a short circuit and damage 
the system.
FUSES