engine GENESIS G90 2023 Owners Manual

5-109
05

[Front door lamp ():
The front or rear room lamps come
on when the front or rear doors are
opened. When doors are unlocked
by the smart key, the front and rear
lamps come on for approximately
30 seconds as long as any door
is not opened. The front and rear
room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Engine
Start/Stop button is in the ON position
or all doors are locked, the front and
rear lamps will turn off. If a door is
opened with the Engine Start/Stop
button in the ACC position or the OFF
position, the front and rear lamps will
stay on for about 5 minutes.

[Front room lamp (
)
Press the button to turn on the room
lamp for the front and rear seats.
Press the button again to turn off all
the lamps.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.
Rear Lamps
ORS051079
ORS051251L
A : Rear seat (if equipped)
B : Rear seat armrest touchscreen (if equipped)

[ : Touch the icon to turn
either lamp on or off.

[
: Touch the icon to turn the lamp
on or off.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.

5-113
05
Puddle Lamp
ORS051084L
Welcome light
When all doors (and trunk) are closed
and locked, the puddle lamp will turn
on for 15 seconds if any of the below is
performed.

[The doors are unlocked by the smart
key.

[The outside door handle touch sensor
is touched with the smart key in
possession.

[The vehicle is approached with the
smart key in possession. (if equipped)
The puddle lamp turns off if the Engine
Start/Stop button is in the ACC position
with a door open.
For more details, refer to “Welcome
System” in this chapter.
Escort light
When the Engine Start/Stop button is in
the OFF position and the driver’s door is
opened, the puddle lamp will turn on for
30 seconds. If the driver’s door is closed
within the 30 second period, the puddle
lamp will turn off after 15 seconds. If the
driver’s door is closed and locked, the
puddle lamp will turn off immediately.
The Puddle Lamp Escort Light will turn
on only the first time the driver’s door is
opened after the engine is turned off.
Welcome System
ORS051077L
Welcome system helps keep the driver
visible by turning on vehicle lights when
the driver approaches the vehicle.

5-115
05
ORS051272
High Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
ORS071001L
M: Front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE
Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
)RUPRUHGHWDLOVRQWKHSUHFDXWLRQV
of the front view camera, refer to

U)RUZDUG&ROOLVLRQ$YRLGDQFH$VVLVW
)&$
VVHFWLRQLQFKDSWHU
High Beam Assist Setting
ORS051241L
With the Engine Start/Stop button in the
21SRVLWLRQVHOHFW
S/LJKWV

5-118
Convenience Features
ORS051284
)URQW:LQGVKLHOG:LSHUV
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS

5-119
05
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:

[Do not touch the upper end of the
windshield glass facing the rain
sensor.

[Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.

[Do not put pressure on the
windshield glass.
NOTICE

[When washing the vehicle, set the
ZLSHUVZLWFKLQWKH2))SRVLWLRQWR
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.

[Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.

[Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Windshield Washers
ORG3EV051079
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield.
The washer fluid is sprayed as the wipers
rise while operating. The spray and wiper
operation will continue until you release
the lever.
If the lever is released, the wipers
operate approximately 4 times and the
lever returns to it's original position

5-120
Convenience Features
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending
on the outside temperature.

[When the air intake control button is
pressed while fresh mode is selected,
air intake control will switch to
recirculation mode.

[When windshield lever is used while
recirculation mode is selected, air
intake control will switch to fresh
mode

[The function may not work in some
conditions such as cold weather or
engine off.
For more details, refer to “Climate
Control Additional Features” section in
this chapter.
Information
)RU*DVROLQH7*',90+(9
vehicles, outside air may enter the vehicle
even while preventing washer fluid scent
IURPIORZLQJLQWKHFDELQWRFRROWKH9
battery.
WARNING
When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent
the washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
NOTICE

[To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.

[To prevent possible damage to the
wipers or windshield, do not operate
the wipers when the windshield is
dry.

[To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.

[To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.

5-135
05
ORS051124
ORS051139L
A : Front seat,
B : Rear seat
Press from the climate control
information screen or armrest
touchscreen to select the desired
fragrance intensity.

[Intensity can be selected among
Strong, Medium and Light. Pressing
the button each time will change
the intensity in the order of Strong,
Medium, Light and Off.

[The fragrance cannot be selected with
the button. Fragrance can only be
selected from the settings menu.
ORS051244
How to replace cartridges
1. Turn the engine off, and open the
glove box.
2. Press the upper part of the diffuser
tray.
3. Replace the cartridge.
Information

[For smooth operation of diffuser, it is
recommended to install 2 cartridges.

[If the cartridge is empty or diffuser
replacement alarm is displayed, replace
with a new cartridge.

[The built-in diffuser may not work if
the cartridge is not installed properly.
&KHFNZKHWKHUWKHFDUWULGJHLVLQVWDOOHG
properly.

5-136
Convenience Features
OFF
ORS051126
ORS051128
A : Front seat control from the front,
B : Rear seat control from the front,
C : Rear seat control from the rear,
D : Front seat control from the rear
Touch the OFF icon or button to turn
the climate control system off. You can
still operate the mode and air intake
buttons as long as the Engine is in the
ON position.

[If OFF is pressed from the front seat,
the front and rear climate control
system will turn off.

[If OFF is pressed from the rear seat,
only the rear climate control system
will turn off.
System Operation
Cooling / Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh or
recirculation mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh or
recirculation mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windshield fogs up, select the Front
Defrost
mode.
2SHUDWLRQ7LSV

[To keep dust or unpleasant fumes
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Return the control to the to
Fresh mode when the unpleasant air
outside has diminished. This will help
keep the driver alert and comfortable.

[To help prevent the inside of the
windshield from fogging, set the air
intake control to fresh mode and the
fan speed to the desired position, turn
on the air conditioning system, and
adjust the temperature control to the
desired temperature.

5-137
05
Air conditioning
Your Genesis Branded Vehicle air
conditioning system is filled with
R-1234yf refrigerant.
1. Start the vehicle.
2. Press the air conditioning button.
3. Set the mode to the Face Level

mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
When maximum cooling is desired, set
the temperature control to the lowest
position, then set the fan speed control
to the highest setting.
NOTICE
When using the air conditioning system,
monitor the engine temperature gauge
closely while driving up hills or in heavy
traffic when outside temperatures are
high. Air conditioning system operation
when climbing a steep grade or in
high outside ambient temperatures
can cause engine overheating.
Continue to use the fan, but turn the air
conditioning system off if the engine
temperature gauge indicates engine
overheating.
Air conditioning system operation tips

[If the vehicle has been parked in
direct sunlight during hot weather,
open the windows for a short time
to let the hot air inside the vehicle
escape.

[After sufficient cooling has been
achieved, switch back from
recirculation mode to fresh mode.

[To help reduce moisture inside of
the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the windows
and sunroof closed.

[Use the air conditioning system
every month only for a few minutes
to ensure maximum system
performance.

[If you operate air conditioner
excessively, the difference between
the temperature of the outside air and
that of the windshield could cause
the outer surface of the windshield to
fog up, causing loss of visibility. In this
case, set the mode selection to the

position and fan speed control to the
lowest speed.

5-141
05
PCM parts
ORS052327N
- Size: 2x2x1 in. (53x53x27 mm)
- Weight: 1.6 oz (46 g)
A: Upper cover
B: PCB & Connector
C: Water protection PCB cover
D: Photo-catalyst
E: Lower cover
F: Leakage protection seal
Direction for use
The PCM, Photo-catalyst Air Purifier
Module for HVAC is activated
automatically when the engine of
automobile is started and deactivated
automatically when the engine is turned
off.
NOTICE

[Do not disassemble, modify or
repair. Any changes or modifications
to product can void your
manufacturer’s warranty.

[If you need servicing, visit a
designated service center.

[Do not use the product for anything
other than its original purpose.

[Do not drop or cause excessive
impact to the product.

[Do not apply any other substances
on the photo catalyst surface.

[If water is on the product, dry it
thoroughly before using it.
NOTICE

[Disposal
Dispose of contents and containers
according to the regulations
stipulated in the wastes control act.

[Storage
-Do not store near acids. As packed
massive products may constitute a
manual handling risk. (e.g., sharp)
-Do not store in areas with high
concentrations of dust or airborne
materials.
WARNING

[This product should be sold
only through and be installed by
automobiles. Other uses are not
acceptable device.

[PCM may be particularly helpful
when additional ventilation with
outdoor air is not possible without
compromising indoor comfort
(temperature or humidity), or when
outdoor air pollution is high.

[The use of PCM alone cannot
ensure adequate indoor air quality,
particularly where significant
pollutant sources are present, and
ventilation is insufficient.
Information
(3$FRPSDQ\QXPEHU.25