Info GENESIS G90 2023 Owners Manual

5-110
Convenience Features
ORS051080
ORS051252L
A : Rear seat (if equipped)
B : Rear seat armrest touchscreen

[ : Press the button to turn the
lamp on or off.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.
Interior Lamp Color Temperature
ORS052253N
ORS051255L
A : Front overhead console
B : Rear armrest touchscreen
M Press the button to turn all the
lamps on. Hold the button for
over 1 second to change the color
temperature as follows.
-:DUP

5-111
05
Interior Lamp Brightness
ORS052254N
ORS051256L
A : Front overhead console
B : Rear armrest touchscreen
M Press the button and turn on all
the lamps. Press and hold the
button for over 1 second to change the
brightness.
N From the lighting menu of the rear
armrest touchscreen, slide the right
sidebar or touch the arrows to change
the brightness in 3 stages.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.
Vanity Mirror Lamp
ORS051274
Opening the lid of the vanity mirror will
automatically turn on the mirror lamp.
Rear Mirror Lamp (if equipped)
ORS051081
Press the cover and it will slowly open
and the mirror lamp will turn on.

5-116
Convenience Features
High Beam Assist Operation
Display and control

[After selecting ‘High Beam Assist’
in the Settings menu, High Beam
Assist will operate by following the
procedure below.
- Place the headlight switch in
the AUTO position and push
the headlight lever towards the
instrument cluster. The High Beam
Assist (
) indicator light will
illuminate on the cluster and High
Beam Assist will be enabled.
- When High Beam Assist is enabled,
high beam will turn on when vehicle
speed is above 25 mph (40 km/h).
When vehicle speed is below 15
mph (25 km/h), high beam will turn
off.
- The High Beam (
) indicator light
will illuminate on the cluster when
high beam is on.

[When High Beam Assist is operating,
if the headlight lever or switch is used,
High Beam Assist operates as follow:
- If the headlight lever is pulled
towards you when the high beam
is off, the high beam will turn
on without High Beam Assist
cancelled. When you let go of the
headlight lever, the lever will move
to the middle and the high beam
will turn off.
- If the headlight lever is pulled
towards you when the high beam is
on by High Beam Assist, low beam
will turn on and High Beam Assist
will turn off.
- If the headlight switch is placed
from AUTO to another position
(headlight/position/off), High
Beam Assist will turn off and the
corresponding lamp will turn on.
[When High Beam Assist is operating,
high beam switches to low beam if
any of the following conditions occur:
- When the headlight of an oncoming
vehicle is detected.
- When the tail lamp of a vehicle in
front is detected.
- When the headlight or tail lamp of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light
is bright enough that high beams
are not required.
- When streetlights or other lights are
detected.
Information
The images and colors in the instrument
may differ depending on the instrument
type or theme selected from the
instrument.

5-117
05
High Beam Assist Malfunction
and Limitations
High Beam Assist malfunction
OJWEV051094L
When High Beam Assist is not working
properly, the ‘Check High Beam Assist
system’ warning message will appear
and
warning light will illuminate on
the cluster. Have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Limitations of High Beam Assist

[Light from an oncoming or front
vehicle is not detected because of
lamp damage, or because it is hidden
from sight, etc.

[Headlight of an oncoming or front
vehicle is covered with dust, snow or
water.

[An oncoming or front vehicle’s
headlights are off, but the fog lamps
are on, etc.

[There is a lamp that has a similar
shape as a vehicle’s lamp.

[Headlights have been damaged or not
repaired properly.

[Headlights are not aimed properly.

[Driving on a narrow-curved road,
curved road, rough road, uphill or
downhill.
[Vehicle in front is partially visible on a
crossroad or curved road.

[There is a traffic light, reflecting sign,
flashing sign or mirror ahead.

[There is a temporary reflector or flash
ahead (construction area).

[The road conditions are bad such as
being wet, iced or covered with snow.

[A vehicle suddenly appears from a
curve.

[The vehicle is tilted from a flat tire or
is being towed.

[Light from an oncoming or front
vehicle is not detected due to
obstacles in the air such as exhaust
fume, smoke, fog, snow, or water spay
or blizzard on the road, or fogging in
the lamp, etc.
Information
For more details on the limitations of the
)URQW9LHZ&DPHUDUHIHUWR

5-118
Convenience Features
ORS051284
)URQW:LQGVKLHOG:LSHUV
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS

5-120
Convenience Features
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending
on the outside temperature.

[When the air intake control button is
pressed while fresh mode is selected,
air intake control will switch to
recirculation mode.

[When windshield lever is used while
recirculation mode is selected, air
intake control will switch to fresh
mode

[The function may not work in some
conditions such as cold weather or
engine off.
For more details, refer to “Climate
Control Additional Features” section in
this chapter.
Information
)RU*DVROLQH7*',90+(9
vehicles, outside air may enter the vehicle
even while preventing washer fluid scent
IURPIORZLQJLQWKHFDELQWRFRROWKH9
battery.
WARNING
When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent
the washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
NOTICE

[To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.

[To prevent possible damage to the
wipers or windshield, do not operate
the wipers when the windshield is
dry.

[To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.

[To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.

5-122
Convenience Features
Rear seat control from the front
1. Temperature control
2. Mode selection
3. AUTO (automatic control)4. OFF (system off)
5. Climate control information screen
6. Fan speed control
ORS052102N
Information
Use microfiber cloth when wiping finger prints off the touchscreen.

5-123
05
Rear seat control (Armrest touchscreen)
ORS052104N
Information

[Press ‘Front’ and select the desired function from the rear armrest touchscreen to
access functions available on the front seats. The following functions are available.
-$872PRGHVHOHFWLRQWHPSHUDWXUHFRQWURODLULQWDNHFRQWUROIDQVSHHGFRQWURO
$&DQGGLIIXVHU

[2SHUDWLQJWKHIDQVSHHGIURPWKHUHDUVHDWDGMXVWPHQWVFUHHQZLOORQO\RSHUDWHWKHUHDU
seat fan speed. 1. Fan speed control
2. Temperature control
3. OFF (system off)4. AUTO (automatic control)
5. Mode selection
6. SYNC (Front and rear seats adjusted
same as the rear seat)

5-124
Convenience Features
1. Driver’s temperature control
2. Passenger’s temperature control
3. Fan speed control
4. Driver’s mode selection
5. Passenger’s mode selection
6. AUTO (automatic control)7. OFF (system off)
8. Air intake control
9. A/C (air conditioning)
10. Built in diffuser
11. Front control
ORS052134N
)URQWVHDWFRQWUROIURPWKHUHDU$UPUHVWWRXFKVFUHHQ
Information
2SHUDWLQJWKHIDQVSHHGIURPWKHIURQWVHDWDGMXVWPHQWVFUHHQZLOORQO\RSHUDWHWKHIURQW
seat fan speed.

5-125
05
Automatic Temperature Control
Mode
The Automatic Climate Control System
is controlled by setting the desired
temperature.
1. Press the AUTO button.
The mode selection, fan speed,
air intake and air-conditioning will
be controlled automatically by the
temperature setting you select.
(To select the rear seat AUTO from
the front seat, press the icon in the
climate control information screen .)
ORS051144
2. When the climate control system is
being automatically controlled, fan
speed can be selected (Low/Medium/
High).

[High: Use when quick heating or
cooling is preferred.

[Medium: Use when medium fan
speed is preferred for cooling or
heating.

[Low: Use when low fan speed is
preferred for cooling or heating.3. Turn the temperature control knob
to the desired temperature. If the
temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
After the interior has cooled
sufficiently, adjust the knob to
a higher temperature set point
whenever possible.
To turn the automatic operation off,
select any function of the following:

[Front windshield defroster button
(Press the button one more time
to deselect the front windshield
defroster function. The ‘AUTO’
sign will illuminate on the climate
information screen once again.)

[Fan speed control icon
The selected function will be controlled
manually while other functions operate
automatically.
For your convenience and to improve the
efficiency of the climate control, use the
AUTO button and set the temperature to
72°F (22°C).
To change the temperature unit from °C
to °F or °F to °C:
Press the AUTO button for 3 seconds
while pressing the OFF button.