display GENESIS G90 2023 Repair Manual

6-20
Driving Your Vehicle
ORS061031L
Vehicle Power limited due to high
transmission temperature
If you continue to drive with overheated
transmission, the above warning
message is displayed and self-protection
mode restricts the power output of the
vehicle.

[Move the vehicle to a safe location
and shift the gear to P (Park), and stop
the vehicle with the engine on. Wait
until the transmission is sufficiently
cooled down.

[If the above message is continuously
displayed, have you contact an
authorized retailer of Genesis Branded
products.
ORS061047L
Transmission cooled and safe to drive
This message is displayed when the
vehicle is safe to drive.

6-31
06
OJX1069034LAUTO HOLD turning Off! Press brake
pedal
When the conversion from Auto Hold to
EPB is not working properly a warning
will sound and a message will appear.
When this message is displayed, Auto
Hold and EPB may not operate. For your
safety, depress the brake pedal.
OJWEV061007L
Press brake pedal to deactivate AUTO
HOLD
If you did not apply the brake pedal when
you release Auto Hold by pressing the
AUTO HOLD switch, a warning will sound
and a message will appear.
Anti-Lock Brake System (ABS)
WARNING
Anti-Lock Braking System (ABS) or
Electronic Stability Control (ESC)
system will not prevent accidents
due to improper or dangerous driving
maneuvers. Even though vehicle
control is improved during emergency
braking, always maintain a safe
distance between you and objects
ahead of you. Vehicle speeds should
always be reduced during extreme
road conditions. The braking distance
for vehicles equipped with ABS or ESC
may be longer than for those without
these systems in the following road
conditions.
Drive your vehicle at reduced speeds
during the following conditions:

[Rough, gravel or snow-covered
roads.

[On roads where the road surface is
pitted or has different surface height.

[Tire chains are installed on your
vehicle.
The safety features of ABS or ESC
equipped vehicle should not be tested
by high speed driving or cornering. This
could endanger the safety of yourself or
others.
ABS is an electronic braking system that
helps prevent a braking skid. ABS allows
the driver to steer and brake at the same
time.

6-35
06
ESC OFF usage
When Driving
The ESC OFF mode should only be used
briefly to help free the vehicle if stuck in
snow or mud, by temporarily stopping
operation of ESC, to maintain wheel
torque.
To turn ESC off while driving, press the
ESC OFF button while driving on a flat
road surface.
NOTICE
To prevent damage to the transmission:

[Do not allow wheel(s) of one axle to
spin excessively while the ESC, ABS,
and Parking Brake warning lights
are displayed. The repairs would not
be covered by the vehicle warranty.
Reduce engine power and do not
spin the wheel(s) excessively while
these lights are displayed.

[When operating the vehicle
on a dynamometer, make sure
ESC is turned off (ESC OFF light
illuminated).
Information
Turning ESC off does not affect ABS or
standard brake system operation.
Vehicle Stability Management
(VSM)
Vehicle Stability Management is a
function of the Electronic Stability
Control (ESC) system. It helps the vehicle
stay stable when accelerating or braking
suddenly on wet, slippery and rough
roads where traction over the four tires
can suddenly become uneven.
WARNING
Take the following precautions when
using Vehicle Stability Management:

[ALWAYS check the speed and the
distance to the vehicle ahead. VSM
is not a substitute for safe driving
practices.

[Never drive too fast for the road
conditions. VSM will not prevent
accidents. Excessive speed in bad
weather, on slippery and uneven
roads can result in severe accidents.

6-44
Driving Your Vehicle
System Malfunction
OJWEV061048L
Check Electronic Suspension
When Electronically Controlled
Suspension with Road Preview is not
working properly, this warning message
will appear on the cluster LCD display. If
this occurs, have the system inspected
by an authorized retailer of Genesis
Branded products.
NOTICE
If the battery level is high or low,
Electronically Controlled Suspension
with Road Preview may not work
temporarily to protect the system. If this
occurs, ‘Check Electronic Suspension’
warning message will appear.
Limitations of the System
Electronically Controlled Suspension
with Road Preview always operates
while driving according to the vehicle’s
movement, and the preview function
starts to work when the front view
camera detects road conditions such as
speed bumps. Therefore, the preview
function is limited when there is an
extreme condition that the front view
camera may not work normally. In this
case, the electronic control suspension
function operates without the preview
function in accordance with vehicle
movement.

6-46
Driving Your Vehicle
Multi-Chamber Air Suspension
Malfunction
OJWEV061048L
This message is displayed when there is
a malfunction with the Multi-chamber
air suspension system. Have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
CAUTION

[When adjusting vehicle height, check
if there are any obstacles below or
above the vehicle.

[If air inside the suspension is
discharged, a warning message
will be displayed. If so, stop driving
and use a towing vehicle. Since
the vehicle height will be very low,
projections on the road may damage
the vehicle. See ‘Towing when the
air suspension malfunctions’ before
towing the vehicle.
Information

[Operating the air suspension may
cause a little noise when charging and
discharging the air.

[Adjusted vehicle height may vary
depending on the temperature and
surrounding environment.

[When the suspension warning message
is displayed, the system enables safe
mode to prevent secondary failure
and the vehicle performance may be
displayed differently.

[When the vehicle is parked on a slope,
or when the vehicle is in unstable
condition due to sudden acceleration,
deceleration or steering, vehicle height
adjustment becomes temporarily
disabled. If the vehicle escapes from
such dangerous situation, vehicle height
adjustment is enabled again.

[When the vehicle is lifted up with a
lift or jack, height adjustment may be
disabled to protect the system. If the
vehicle engine is started or you start
driving, the function is enabled again.

[Leaving the vehicle parked for long
time may lower the vehicle height. The
vehicle height returns to its original
position when the engine is started.

[If the battery is either overcharged or
discharged, vehicle height adjustment
is disabled to protect the system and a
temporary warning message may be
displayed.

[If the vehicle height adjustment is
operated repeatedly, the function may
be temporarily disabled due to the
overheated compressor. It is to prevent
the breakdown of related parts.

6-47
06
Additional Height Adjustment
Function
Multi-chamber air suspension recognizes
the driving condition to automatically
adjust vehicle height, spring stiffness,
and shock absorber damping force for
driving comfort and vehicle protection.
Additional vehicle height adjustment
operates automatically depending
on various conditions and it is not
necessarily displayed to the driver.
Off road driving
ORS061027
The vehicle adjusts vehicle height, spring
stiffness, and shock absorber damping
force when driving on a rough terrain
such as an unpaved road, to optimize
comfort and protect the vehicle.
Driving on a slope
ORS061028
The vehicle adjusts vehicle height, spring
stiffness, and shock absorber damping
force when driving over a steep slope,
to optimize comfort and protect the
vehicle.
Information

[Additional vehicle height adjustment
function operates differently
depending on various driving and
system conditions. In some cases, its
operability and actuation speed may
vary.

[When the vehicle speed is below 6 mph
(10 km/h) or above 37 mph (60 km/h),
the safety bump driving function may
be disabled.

[When the vehicle speed is above 18
mph (30 km/h), the off road driving
and slope driving function may be
disabled.

6-50
Driving Your Vehicle
In the Auto Stop mode, if the engine
hood is opened, ISG system will be
deactivated.
When the system is deactivated, a
message ‘Auto Stop is off. Shift to P or
N to start engine manually’ appears on
the cluster LCD display with a warning
sound.
If this occurs, depress the brake pedal
and restart the engine manually.
Auto start
When the engine stops automatically by
ISG, the engine will restart if one of the
following is done.
-Release the brake pedal.
-When Auto Hold is activated, take
your foot off the brake pedal and then
depress the accelerator pedal.
-While depressing the brake pedal,
shift the gear from N (Neutral) or D
(Drive) to R (Reverse) or P (Park).
-While depressing the brake pedal,
shift the gear from N (Neutral) to D
(Drive).
The Auto Stop (
) indicator turns into
white on the instrument cluster, when
the engine is restarted.
LCD display messages
The messages are displayed on the
instrument cluster to help use ISG
system.
ORS061032L
Auto Stop is Off. Shift to P or N and start
engine manually
When the system is deactivated, a
message will appear on the cluster LCD
display with a warning sound in the
following situations.
-When the engine hood is opened.
-When ISG system is not working
normally.
If this occurs, depress the brake pedal
and restart the engine manually. For your
safety, restart the vehicle in the P (Park)
position.

6-51
06
ORS061049L
AUTO STOP elapsed time
AUTO STOP display shows the elapsed
time of engine stop by the Idle Stop and
Go system.
You may check AUTO STOP elapsed time
in the Normal view on the instrument
cluster.
Refer to “View Modes” section in chapter
4.
ISG System Off
ORS061022L
Press the ISG OFF button to turn off ISG
system. The ISG OFF button indicator will
illuminate. To use the system, press the
ISG OFF button again.

6-57
06
Limitations of the System
The predictive shift may have limited
operation in the following situations

[If you do not take the route guided in
the navigation, predictive shift may
not operate properly since the system
operates according to the navigated
route. Predictive shift will operate
properly again once the navigation
sets a new route.

[The navigation may reflect the real
time traffic condition and change the
route. If so, the predictive shift may
not correspond temporarily to the
current driving condition.

[If the destination is not set on the
navigation, predictive shift operates
according to the route which is most
likely to be taken. When driving
through roads such as a branch road,
predictive shift may not correspond to
the current driving condition until the
navigation sets a new route.

[While using the navigation app
through smart phone linked functions
such as Android Auto or Apple
CarPlay, predictive shift operates as
when the destination is not set in the
vehicle’s navigation.

[Predictive shift may not operate
properly in the following situations.
-Navigation system is not completely
booted.
-Real time GPS or map data has
errors, or the map data is not up to
date.
Checking Operation on the
Instrument Cluster
The operating condition of predictive
shift can be checked from the icons and
messages displayed on the instrument
cluster. If there are multiple conditions
detected, every related icon illuminates
but only the most important message
is displayed. The images and colors
of the messages may differ from the
description depending on the cluster
type.
CAUTION
Always be aware of the traffic and
road condition ahead. Checking the
instrument cluster while driving
may cause an accident.
When predictive shift is ready
ORS062039N
Refer to the following for icons displayed
when predictive shift is stand-by for use.

6-65
06
Road Active Noise Control helps reduce
noise caused while driving.
The system may not operate properly in
the following conditions:

[Any of the window is open

[Any of the door is open

[The sunroof is open

[The trunk is open

[Vehicle’s microphone and speaker is
blocked by loads
System Malfunction
OJWEV061046L
When Road Active Noise Cancel is
malfunctioning, this warning message
will appear on the cluster LCD display. If
this occurs, have the system inspected
by an authorized retailer of Genesis
Branded products.
ROAD ACTIVE NOISE
&21752/