GENESIS GV60 2023 Owners Manual

7-67
07

[When a pedestrian or bicycle is
between you and the vehicle ahead
OJWEV071090
If there is a pedestrian(s) or bicycle(s)
in between you and the vehicle in
front, Leading Vehicle Departure Alert
may not operate properly.

[When in a parking lot
OJWEV071088
If a vehicle parked in front drives away
from you, Leading Vehicle Departure
Alert may alert you that the parked
vehicle is driving away.
[When driving at a tollgate or
intersection, etc.
OJWEV071089
If you pass a tollgate or intersection
with lots of vehicles or you drive
where lanes are merged or divided
frequently, Leading Vehicle Departure
Alert may not operate properly.
Information
For more details on the precautions of
the front view camera, refer to “Forward
Collision-Avoidance Assist (FCA)” section
in this chapter.

7-68
Driver Assistance System
%/,1'

7-69
07
Blind-Spot View Monitor
Operating conditions
When the left or right side turn signal
turns on, the image in that direction is
displayed on the instrument cluster.
Off conditions

[When the turn signal turns off, the
image on the instrument cluster will
turn off.

[When the hazard warning flasher
is on, Blind-Spot View Monitor will
turn off, regardless of the turn signal
status.

[When other important warning is
displayed on the instrument cluster,
Blind-Spot View Monitor may turn off.
%OLQG6SRW9LHZ0RQLWRU
Malfunction
When Blind-Spot View Monitor is not
working properly, or the cluster display
flickers, or the camera image does not
display properly, have the vehicle be
inspected by an authorized retailer of
Genesis Brand products.
:$51,1*

[7KHLPDJHVKRZQRQWKHFOXVWHUPD\
differ from the actual distance of the
REMHFW0DNHVXUHWRGLUHFWO\FKHFN
WKHYHKLFOH
VVXUURXQGLQJVIRUVDIHW\

[$OZD\VNHHSWKHFDPHUDOHQVFOHDQ
,IWKHOHQVLVFRYHUHGZLWKIRUHLJQ
PDWHULDOLWPD\DGYHUVHO\DIIHFW
FDPHUDSHUIRUPDQFHDQG%OLQG
6SRW9LHZ0RQLWRUPD\QRWRSHUDWH
SURSHUO\

7-70
Driver Assistance System
60$57&58,6(&21752/

7-71
07
Smart Cruise Control Settings
OJWEV071255L
Based on Driving Style (if equipped)
With the vehicle on, if ‘Driver Assistance

7-72
Driver Assistance System
OJWEV071238L
Warning Volume
With the vehicle on, select ‘Driver
$VVLVWDQFH

7-73
07
Overtaking Acceleration Assist
Overtaking Acceleration Assist operates
when the turn signal indicator is turned
on while Smart Cruise Control is
operating, and the following conditions
are satisfied:

[Your vehicle speed is above 40 mph
(60 km/h)

[The hazard warning flasher is off

[A vehicle is detected in front of your
vehicle

[Deceleration is not needed to
maintain distance with the vehicle in
front
:$51,1*

[When the turn signal indicator is
WXUQHGRQZKLOHWKHUHLVDYHKLFOH
DKHDGWKHYHKLFOHPD\DFFHOHUDWH
WHPSRUDULO\3D\DWWHQWLRQWRWKH
URDGFRQGLWLRQVDWDOOWLPHV

[5HJDUGOHVVRIWKHGULYLQJGLUHFWLRQ
LQ\RXUFRXQWU\2YHUWDNLQJ
Acceleration Assist will operate when
WKHFRQGLWLRQVDUHVDWLVILHG:KHQ
using the function in states with
GLIIHUHQWGULYLQJGLUHFWLRQDOZD\V
check the road conditions at all
WLPHV
OJWEV071081
Turning on Smart Cruise Control

[Press the Driving Assist () button
to turn on Smart Cruise Control. The
speed will be set to the current speed
on the cluster.

[If there is no vehicle in front of you,
the set speed will be maintained, but
if there is a vehicle in front of you,
the speed may decrease to maintain
the distance to the vehicle ahead. If
the vehicle ahead accelerates, your
vehicle will travel at a steady cruising
speed after accelerating to the set
speed.
Information
If your vehicle speed is between 0-20 mph
(0-30 km/h) when you press the Driving
Assist (
) button, the Smart Cruise
Control speed will be set to 20 mph (30
km/h).

7-74
Driver Assistance System
OJWEV071136
Setting vehicle distance
Each time the button is pressed, the
headway changes as follows:
Distance 4 Distance 3
Distance 1Distance 2
Information

[If you drive at 56 mph (90 km/h), the
distance is maintained as follows:
Distance 4 -
approximately 172 ft. (53 m)
Distance 3 -
approximately 130 ft. (40 m)
Distance 2 -
approximately 106 ft. (30 m)
Distance 1 -
approximately 82 ft. (25 m)

[The distance is set to the last set
distance when the vehicle is restarted,
or when Smart Cruise Control was
temporarily cancelled.
OJWEV071132
Increasing set speed

[Push the + switch up and release
it immediately. The set speed will
increase by 1 mph (1 km/h) each time
the switch is operated in this manner.

[Push the + switch up and hold it while
monitoring the set speed on the
cluster. The set speed will increase by
5 mph (10 km/h) each time the switch
is operated in this manner. Release
the switch when the desired speed is
shown, and the vehicle will accelerate
to that speed. You can set the speed
to 120 mph (200 km/h).
:$51,1*
&KHFNWKHGULYLQJFRQGLWLRQEHIRUH
XVLQJWKHVZLWFK'ULYLQJVSHHGPD\
VKDUSO\LQFUHDVHZKHQ\RXSXVKXSDQG
KROGWKHVZLWFK

7-75
07
OJWEV071133
Decreasing set speed

[Push the - switch down and release
it immediately. The set speed will
decrease by 1 mph (1 km/h) each time
the switch is operated in this manner.

[Push the - switch down and hold it
while monitoring the set speed on the
cluster. The set speed will decrease by
5 mph (10 km/h) each time the switch
is operated in this manner.
Release the switch at the speed you
want to maintain. You can set the
speed to 20 mph (30 km/h).
OJWEV071134
Temporarily cancelling Smart Cruise
Control
Press the switch or depress the
brake pedal to temporarily cancel Smart
Cruise Control.
OJWEV071135
Resuming Smart Cruise Control
To resume Smart Cruise Control after the
function was cancelled, operate the +, -
or
switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the cluster.
If you press the
switch, vehicle
speed will resume to the preset speed.
:$51,1*
&KHFNWKHGULYLQJFRQGLWLRQEHIRUH
using the VZLWFK'ULYLQJVSHHG
PD\VKDUSO\LQFUHDVHRUGHFUHDVHZKHQ
\RXSUHVVWKH
VZLWFK

7-76
Driver Assistance System
OJWEV071081
Turning off Smart Cruise Control
Press the Driving Assist () button to
turn Smart Cruise Control off.
Information
If your vehicle is equipped with Manual
Speed Limit Assist, press and hold the
Driving Assist (
) button to turn off
Smart Cruise Control. However Manual
Speed Limit Assist will turn on.
Display and control
You can see the status of the Smart
Cruise Control operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Smart Cruise Control will be displayed
as below depending on the status of the
function.
OJWEV071028E
Basic function

[When operating
(1) Whether there is a vehicle ahead and
the selected distance level
(2) Set speed
(3) Whether there is a vehicle ahead and
the target vehicle distance

[When temporarily cancelled
(1) Your vehicle (shaded)
(2) The previous set speed (shaded)
(3) Whether there is a vehicle ahead
(shaded) (if equipped)