infotainment GENESIS GV60 2023 Repair Manual

7-125
07
Rear View while driving
The driver can check the rear view on
the screen while driving. The rear view
while driving consist of a rear view
while driving and a rear wide view while
driving. Also, you can change the view
mode you want to select by pressing
the view button (2) on the infotainment
system screen.
Rear View while driving function will turn
on under the following conditions:

[The Parking/View button (1) is
pressed, while driving above 9 mph
(15 km/h).

[
is selected among the view buttons
(2) when vehicle speed is 9 mph (15
km/h) or less.
Rear View while driving function will turn
off under the following conditions:

[The Parking/View button (1) or the
infotainment system button (1) is
pressed.

[The gear is shifted to P (Park).

[The Parking/View button (1) is
pressed.

[The Home button (4) is pressed.

[Other view modes are selected when
vehicle speed is 9 mph (15 km/h) or
less.
3D view
The 3D view shows the image around the
vehicle from various angles.
You can change angles by tapping the
screen. Press the 3D View button again
to return to the initial angle.
3D view will turn on when the 3D view
is selected among the view buttons (2)
under the following conditions:

[The gear is in P (Park), N (Neutral) or D
(Drive) when vehicle speed is below 9
mph (15 km/h).

[The Surround View Monitor is turned
on when the gear is in R (Reverse).
When the gear is in P (Park), N (Neutral)
or D (Drive), 3D view will turn off under
the following conditions:

[The gear is shifted to P (Park).

[The Parking/View button (1) is
pressed.

[The infotainment system button (3) is
pressed.

[The Home button (4) is pressed.

[Vehicle speed is above 9 mph (15
km/h).
Information
3D view does not display guidelines.

7-130
Driver Assistance System
Rear Cross-Traffic Collision-
$YRLGDQFH$VVLVW2SHUDWLRQ
Warning and control
Rear Cross-Traffic Collision-Avoidance
Assist will warn and control the vehicle
depending on collision risk level:
‘Collision Warning’, ‘Emergency Braking’
and ‘Stopping vehicle and ending brake
control’.
OPDEN060039OJWEV071040N
OJWEV071225L
Collision Warning

[To warn the driver of an approaching
a detected vehicle from the rear left/
right side of your vehicle, the warning
light on the outside rearview mirror
will blink and a warning will appear
on the cluster. At the same time, an
audible warning will sound and the
steering wheel will vibrate. If the Rear
View Monitor is operating, a warning
will also appear on the infotainment
system screen.
[Rear Cross-Traffic Collision-Avoidance
Assist will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching a detected vehicle
is within approximately 82 ft. (25 m)
from the left and right side of your
vehicle
- The speed of the a detected vehicle
approaching from the left and right
is above 3 mph (5 km/h)
Information

[If the operating conditions are satisfied,
there will be a warning whenever the
vehicle approaches from the left or
right side even though your vehicle
speed is 0 mph (0 km/h).

[The images and colors in the cluster
may differ depending on the cluster
type or theme selected from the cluster.

7-131
07
OPDEN060039OJWEV071041L
OJWEV071225L
Emergency Braking

[To warn the driver of an approaching
a detected vehicle from the rear left/
right side of your vehicle, the warning
light on the outside rearview mirror
will blink and a warning message will
appear on the cluster. At the same
time, an audible warning will sound
and the steering wheel will vibrate.
A warning will also appear on the
infotainment system screen.
[Rear Cross-Traffic Collision-Avoidance
Assist will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching a detected vehicle
is within approximately 5 ft. (1.5 m)
from the left and right side of your
vehicle
- The speed of the a detected vehicle
approaching from the left and right
is above 3 mph (5 km/h)

[Emergency braking will be assisted
to help prevent collision with
approaching vehicles from the left
and right.
:$51,1*
%UDNHFRQWUROHQGVZKHQWKHFRQGLWLRQV
RIWKHDSSURDFKLQJYHKLFOHIURPWKH
UHDUOHIWRUULJKWVLGHDUHDVEHORZ

[7KHDSSURDFKLQJYHKLFOHLVRXWRIWKH
detecting range

[7KHDSSURDFKLQJYHKLFOHSDVVHV
EHKLQG\RXUYHKLFOH

[7KHDSSURDFKLQJYHKLFOHGRHVQRW
GULYHWRZDUG\RXUYHKLFOH

[7KHDSSURDFKLQJYHKLFOHVSHHGVORZV
down

[7KHGULYHUGHSUHVVHVWKHEUDNHSHGDO
with sufficient power

7-156
Driver Assistance System
Operating conditions
Select ‘Rear Safety’ from the ‘Parking
Safety’ menu of the infotainment system.
Parking Collision-Avoidance Assist is
enabled when the following conditions
are satisfied:
Rear Safety

[The liftgate and door are closed

[The Electronic Parking Brake (EPB) is
released

[A trailer is not connected

[The gear is shifted to R (Reverse)

[Vehicle speed is below 6 mph (10
km/h) (detecting pedestrians)

[Vehicle speed is below 2.4 mph (4
km/h) (detecting objects)

[Parking Collision-Avoidance Assist
components such as the rear view
camera and the rear ultrasonic
sensors are in normal conditions
Front/Side Safety

[The liftgate and door are closed

[The Electronic Parking Brake (EPB) is
released

[A trailer is not connected

[The gear is shifted to R (Reverse) or D
(Drive)

[Vehicle speed is below 2.4 mph (4
km/h) (for pedestrians, objects)

[Parking Collision-Avoidance Assist
components such as the wide rear
view camera and the rear ultrasonic
sensors are in normal conditionsWhen Parking Collision-Avoidance Assist
activates, a line appears behind the
vehicle image in the instrument cluster.

[Rear Safety: Behind the vehicle image

[Front/Side Safety: In front of vehicle
image
OJWEV071357N
Information
Parking Collision-Avoidance Assist
operates only once after shifting the gear
to R (Reverse) or D (Drive). To reactivate
Parking Collision-Avoidance Assist, shift
the gear from another gear to R (Reverse)
or D (Drive).

7-157
07
Parking Collision-Avoidance Assist
If Parking Collision-Avoidance Assist
detects a risk of collision around the
vehicle with a pedestrian or an object,
Parking Collision-Avoidance Assist will
warn the driver with an audible warning
and warning message on the instrument
cluster. If the infotainment screen is on,
a warning will appear on the screen.If
collision is imminent, Parking Collision-
Avoidance Assist will assist you with
braking.
Front/Side Safety
Braking assist is released 2 seconds at
D (drive) and 5 minutes at R (reverse).
Immediately depress the brake pedal
and check vehicle surroundings. Braking
assist is also released in the following
conditions when:

[The gear is shifted to other positions
but N(Neutral)

[The brake pedal is depressed with
sufficient power
Rear Safety
Braking assist is released after 5 minutes.
Immediately depress the brake pedal
and check vehicle surroundings. Braking
assist is also released in the following
conditions when:

[The gear is shifted to P (Park) or D
(Drive)

[The brake pedal is depressed with
sufficient power
Information
When Parking Collision-Avoidance Assist
is activated while reversing, braking
control will be released after 5 minutes
and the Electronic Parking Brake (EPB)
will be engaged.
3DUNLQJ&ROOLVLRQ$YRLGDQFH
Assist Malfunction and
Limitations
Parking Collision-Avoidance Assist
malfunction
OJWEV071300LOJWEV071350N
When Parking Collision-Avoidance
Assist or other related functions are not
working properly, the ‘Check Parking
Safety system’ warning message will
appear on the cluster, and Parking
Collision-Avoidance Assist will turn
off automatically. Have the vehicle be
inspected by an authorized retailer of
Genesis Branded products.

7-167
07
Remote Operation
Operating order
Remote Operation function operates in
the following order:
1. Getting ready to remotely move
forward and backward
2. Remotely moving forward and
backward
*HWWLQJUHDG\WRUHPRWHO\PRYHIRUZDUG
DQGEDFNZDUG
There are two ways to operate Remote
Operation function.
OJWEV071155
Method (1) Using the function with
vehicle off
(1) Within a certain range from the
vehicle press the door lock (
)
button on the smart key and lock
all doors.
(2) Press and hold the Remote Start
button (
) within 4 seconds until
the vehicle starts.

[For more details on remotely
starting the vehicle, refer to
“Remote Start” section in chapter 6.
OJWEV071156N
OJWEV071277L
Method (2) Using the function with
vehicle on
(1) Park the vehicle in front of the
space where you want to use
Remote Operation function, and
shift the gear to P (Park).
(2) Press and hold the Parking/View
(
) button to turn on Smart
Parking Assist. A message ‘Remote
Parking Instructions’ will appear
on the infotainment system
screen.
(3) Get out of the vehicle with the
smart key and close all doors.

7-168
Driver Assistance System

['Agree' must be selected on the
infotainment system screen and the
infotainment system has to operate
properly to use Remote Operation
function.

[Method (2) can be used after the
vehicle has been driven above 3
mph (5 km/h).

[If the function is turned on again
after parallel parking is completed
by Remote Smart Parking Assist,
Remote Operation function can be
used with Method (2).

[Check that all smart keys are
outside the vehicle when using
Remote Operation function.
5HPRWHO\PRYLQJIRUZDUGDQG
EDFNZDUG
OJWEV071157
(1) Press and hold one of the Forward
() or Backward () button on
the smart key. Remote Smart
Parking Assist will automatically
control the steering wheel, vehicle
speed and gearshift. The vehicle
will move in the direction of the
button pressed. (2) While Remote Operation function
is operating, if you do not
hold down the Forward (
) or
Backward () button, the vehicle
will stop and function control
will pause. The function will start
operating again when the button is
pressed and held again.
(3) When the vehicle reaches the
target location, release the smart
key Forward or Backward button.
(4) When the driver gets in the vehicle
with the smart key, a message
will appear informing the driver
Remote Operation function is
complete on the infotainment
system screen and the vehicle will
remain on.
In addition, when the Remote Start
(
) button is pressed on the smart
key from outside the vehicle, a
message will appear informing the
driver Remote Operation function
is complete and the vehicle will
turn off.

7-170
Driver Assistance System
Remote Operation function operation
status
Operation
status6PDUWNH\/('+D]DUG
warning
light
Under
controlGreen LED
continuously
blinks-
PauseRed LED
continuously
blinksBlinks
OffRed LED
illuminates for
4 seconds and
then turns offBlinks 3
times and
turns off
CompleteGreen LED
illuminates for
4 seconds and
then turns offBlinks 1
time and
turns off
ÃOperation status by the hazard
warning light may not be applicable
based on the regulation of your
country.
ÃIf the smart key is not within the
operating range from the vehicle
(approximately 13 ft. (4 m)), the
smart key LED will not illuminate or
blink. Use the smart key within the
operating range.
How to turn off Remote Operation
function while operating

[Press the Parking/View () button
while the infotainment system screen
guides the driver using method 2.

[Shift the gear except to P (Park)
while the infotainment system screen
guides the driver using method 2.

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen.

[Press the Remote Start (
) button
on the smart key while the vehicle is
being controlled by Remote Operation
function. Remote Operation function
will turn off. At this time, the vehicle
will turn off.

[Get on the vehicle with the smart
key. Remote Operation function will
turn off. At this time, the vehicle will
remain on.
The function will pause in the following
conditions when:

[There is a detected pedestrian, animal
or object in the direction the vehicle
is moving

[The door or liftgate is open

[The Forward (
) or Backward ()
button is not continuously pressed

[Simultaneously pressing multiple
buttons on a smart key

[The smart key is not operated within
13 ft. (4 m) from the vehicle

[Button of another smart key is pressed
in addition to the operating smart key

[Blind-Spot Collision-Avoidance
Assist or Rear Cross-Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction.

7-172
Driver Assistance System
Smart Parking, Remote Smart
Parking
Operating order
Parking function operates in the
following order:
1. Getting ready for parking
2. Searching for parking space
3. Select parking type and operating
mode
4. Smart Parking
5. Remote Smart Parking

[Parking function includes Smart
Parking and Remote Smart Parking.
*HWWLQJUHDG\IRUSDUNLQJ
OJWEV071102
(1) With the vehicle turned on,
depress the brake pedal and shift
the gear to D (Drive) or N (Neutral).
(2) Press and hold the Parking/View
(
) button to turn on Remote
Smart Parking Assist.

['Agree' must be selected on the
infotainment system screen and the
infotainment system has to operate
properly to use Parking function.

[If you drive above 3 mph (5 km/h)
with the vehicle on, you may use
the Parking function with the gear
shifted to N (Neutral).
6HDUFKLQJIRUSDUNLQJVSDFH
OJWEV071278L
(1) Slowly drive forward maintaining
the distance of approximately 40
in. (100 cm) from the parking lines
or the parked vehicles.
(2) When searching for a parking
space is complete, a message will
appear on the infotainment system
screen with an audible sound to
notify the search is complete.
(3) ‘Select Parking Type’ will be
displayed on the infotainment
system screen and the selected
parking space will appear on Top
View screen of Surround View
Monitor.

7-173
07

[Remote Smart Parking Assist
searches parking lines or parking
spaces that are next to parked
vehicles, or parking spaces with
parked vehicles in front or rear.

[While searching for a parking space,
when vehicle speed is above 12 mph
(20 km/h), a message will appear
on the infotainment system screen
informing you to slow down. When
vehicle speed is above 18 mph (30
km/h), Parking function will turn off.

[Searching for a parking space will
be completed when there is enough
space to move the vehicle in
addition to the parking space.

[Even if an audible sound is heard
to notify that searching for a
parking space is complete, search
completion can be cancelled
immediately depending on
surroundings. Information
OJWEV071125N[A] : Searching for parking space

[If the distance is below 20 in. (50 cm)
or over 59 in. (150 cm), Remote Smart
Parking Assist may not be able to
search for a parking space.

[If you do not maintain a certain
distance from the parked vehicle, the
performance to search for a parking
space may reduce.

[Due to abnormal performance of the
ultrasonic sensor or the influence of
the surroundings, Parking function
may not be able to search for a parking
space even if there is a parking space,
or may search for a space that is not
suitable for parking.

[If the parking space is on a incline or
is diagonal, the parking type displayed
may be different from the actual
parking type which should be selected.
If this occurs, do not select the parking
type, and search for another parking
space.