wheel GREAT WALL PEGASUS 2006 Service Manual

BE-32Body Electric System
Combination Instrument
Combination instrument
Electric circuit diagram

  



^N ^NS _N _ N P
DraêaáÉëÉärear fog lamp indicating lamp
rear window/defroster indicating lamp
upper beam indicating lamp
front fog-lamp indicating lamp
A13
B3

connected
with
negative
pole
A10
connected
with
positive
pole
A2
connected
with
negative
polewater
thermometer
tachometer
speedometerconnected with sensor
connected with revolution signal
connected with sensor anode
connected with sensor
fuel gauge
connected with sensor
braking liquid level indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp
left turn indicating lamp
right turn indicating lamp
instrument interior
lighting lamp
liquid crystal back-light lamp
A1A16 B1 A5 A6A7 A8 A9 B6 B8 B9B10 B11A12 B4
A15
A14
A10
connected
with
positive
pole
A3
A4
B12
B13
B5
A13
B3

connected
with
negative
pole
A10
connected
with
positive
pole
A2
connected
with
negative
pole
liquid crystal back-light lampinstrument interior
lighting lamp
rear fog lamp indicating lamp
upper beam indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
speedometer
fuel gaugeconnection with sensor
connected with revolution signal
connected with sensor anode
connected with sensor
connected with sensor
oil-water separation indicating lamp
safety belt indicating lamp
parking brake indicating lamp
braking liquid level indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp
left turn indicating lamp
right turn indicating lamp
A1 A16 B1
A5 A6 A7A8
A9 B6 B8
B9 B10
B11 A4A12 A14 A15B4
A10
connected
with
positive
pole
A3
B12
B13
B5

BE-33Body Electric System
Combination Instrument
Electric circuit diagram (continued)
SF
A3 connected
with negative pole
A1 connected
with positive pole
B8 connected
with negative
pole
B7connected
with positive
pole
A4 connecting
with lighting
switch
A6 connected
with negative
pole
pressure-regulating
potential deviceirect-current
power supply
5-9Vdrive power
supply
110VEL
luminous
plate
left turn indicating lamp
right turn indicating lamp
upper beam indicating lamp
rear fog lamp indicating lamp
rear window/defroster indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
connected with sensor
connected with revolution signal
speedometer
digital clock
fuel gaugeconnect to the cathode of sensor
connected with sensor anode
connected with sensor
connected with sensor
back door indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp75
B9
B2 A15 B1 A9 B11 B10
A14 B4 B6 A12
B14 connected
with positive
pole
B7 connected
with positive
pole
A11 A5A7 B12B5 B13 A16A13 B16 B15
A2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
In this drawing, A stands for the white plugging
elements, B for black plugging elements, they
use the same numerical order.
instrument
plugging element

BE-34Body Electric System
Combination Instrument
Electric circuit diagram (continued)
A16 A1 B16 B1
SL SK
B1
B16
A1
A16
speed and mileage meter
4P
G
VA9vehicle speed signal
A11odometer sensorA10odometer sensor anode
B11sensor signalelectronic tachometer
water thermometer
fuel gaugecoolant temperature sensor
B5
A12
fuel gauge sensor
B14
A2
B3
upper beam
_NPdifferential latch-in
safety belt
preheating
sediment water alarmingelectricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 Aturn indicating lamp
B16 left turn indicating lamp
A8
B4 +B7 - B8 A16 B15 B2B1 A15 A14B6 A13 B10B9
SY SJaccumulator plus four door-closing indicating lampA3turn on when the door is opened.
A11odometer sensor_NO
electronic odometer
electronic tachometerA10
B11
engine ignition coil
water thermometer
fuel gauge
B5
A12
neutral gear indicating lampA9
_NP
upper beamB14
differential latch-in
vacuum alarming
preheating
sediment water alarming
electricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 left turn indicating lamp
B16 right turn indicating lamp
A8
B4 +
instrument lighting
system
B8
B7 - A16 B15 B2
B1 A15A14 B6 A13 B9 B3 B10A2
instrument lighting
system

BE-35Body Electric System
Combination Instrument
Common Troubleshooting
a. Such failures as inaccuracy indication, out-operation of indicator, on the fly of large and small summation meters
(mechanical wheel drive excluded) or incomplete liquid crystal display are caused by the interior failures of the
instrument, therefore, these failures, once occur, should be judged according to the instrument interior failures, and
change the combination instrument directly.
b. In case both the large and small summation meter and the indicator of electronic odometer are on the fly, such failures
can be removed by disassembling the speed sensor from the whole vehicle first, then connecting the sensor and
combination instruments as shown in the drawing.
Then, open the power supply and run the rotors quickly to observe the indicator variation of odometer.
the odometer indicator
should be no less than 40Km/
h variation in speed under
common condition whenrunning the rotors,
otherwise,
change with the good sensor
good combination instruments
vÉë
No
Yes
No
Yes
No
installation of sensorconnector for wiring harnessmalfunction of sensorfailure of instrument
panel connector for wiring
harness


12V

combination instrument




signal input
sensor

BE-37Body Electric System
Backup Radar System
Backup Radar System
Dr SF
SL SK
back up radar control box
back up radar control box
right rear wheel
left rear wheel
rear bumper
Part Mounting Position

B0-1
Vehicle Body
Page
Introduction ................................................................. BO-2
Engine cover ............................................................... BO-3
Front door .................................................................... BO-4
Rear car Door .............................................................. BO-10
Body collision avoidance adhesive strip ...................... BO-20
Wheel-trims ................................................................. BO-24
Wheel-trims wrapping angle and exterior trim panel ... BO-26
Front Windshield ......................................................... BO-32
Side-window glass ...................................................... BO-37
Rear-door glass ........................................................... BO-40
Rear windshield ........................................................... BO-41
Load-compartment baffle ............................................ BO-43
Tail door ....................................................................... BO-45
Instrument panel ......................................................... BO-50
Safety belt ................................................................... BO-57
Seat ............................................................................. BO-60
Spoiler ......................................................................... BO-63
Luggage rack .............................................................. BO-65
Reserve tire bracket .................................................... BO-66
Body dimension ........................................................... BO-68
Frame dimension ........................................................ BO-78
BO

B0-24
Wheel-trims
Wheel-trims of stainless steel
Element mounting position
Vehicle Body
Wheel-Trims
Change of shield of front wheel
1. Tear down the shield of front wheel;
Tear down the five screws to take down the Wheel-trims;
2. Mount the shield of front wheel
(a) Tap the front shield manually to ensure it contact the
body closely.
(b) Mount the five screws.
shield of front wheel
rear wheel-trims
Dr
Change of rear Wheel-trims
1. Tear down the rear Wheel-trims.
Tear down the five screws and take down the Wheel-trims.
Prize up the snapping plate of Wheel-trims with screwdriver to
take down the Wheel-trims (SF)
2. Mount the rear Wheel-trims:
(a) Tap the rear Wheel-trims manually to ensure it contacts
the body closely.
(b) Mount the five screws.
Clamp the Wheel-trims with snapping plate. (SF)

B0-25
large wheel trims
Element mounting position
Vehicle Body
Wheel-Trims
shield of front wheel
wrapping angle of
shield of front wheel
rear wheel-trims
SF
Change of shield of front wheel and wrapping angle
1. Tear down the shield of front wheel and wrapping angle;
Tear down the seven screws and take down the Wheel-trims.
2. Mount the shield of front wheel:
(a) Mount the adhesive strip of Wheel-trims first, ensure the adhesive
strip contact the Wheel-trims closely;
(b) Mount the five screws.
3. Mount the wrapping angle of the front Wheel-trims.
Mount the wrapping angle on the front bar first, and then fix it with two
screws.
Change of rear wheel-trims
1. Tear down the rear Wheel-trims
Tear down the five screws and take down the Wheel-trims;
2. Mount the rear Wheel-trims
(a) Mount the adhesive strip of Wheel-trims first, ensure the adhesive
strip contact the Wheel-trims closely;
(b) Mount the five screws

B0-26
Wheel-trims wrapping angle and exterior trim panel (
)
Element mounting position
Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel
adhesive strip of wheel-trims
front wheel-trimsrear wheel-trims
front wrapping anglerear wrapping angle
SY

B0-27
Wheel-trims wrapping angle and exterior trim panel (
)
Element mounting position
Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel
trim panel at front door front wheel-trimsrear wheel-trims
front wrapping anglerear wrapping angle
Top-grade SY
trim panel at rear door
luminous channel