plug GREAT WALL SAFE 2006 Owner's Manual

BE-3Body Electric System
Brief Introduction
pull up
pull up
press down press down
Change of fuse and maxi-fuse
Remark: in case of exchanging the fuse or maxi-fuse, the fuse
or maxi-fuse with same rated current should be used.
Notice:
1. Before exchanging the fuse or maxi-fuse, all electric
appliances and ignition switches should be turned off
firstly. And the rated current of fuse or maxi-fuse should
not be exceeded.
2. When disassembling or assembling the fuse, the
disassembly and assembly tools must be used. And they
must be pulled out or plugged in vertically. No bend is
allowed because the bend will make the connecting
terminals depart away, and thus poor connection will
occur. In case the fuse or maxi-fuse is burned, it shows
there is short circuit. In such situation, the systematic
inspection should be conducted by the qualified
technician.
Remark: the disassembly and assembly tools are put on the
protective box cover.
same rated current 10A
10A

BE-4
How to make systematic inspection
The inspection order is a simple troubleshooting approach, which is used to check and diagnose the failure on vehicle
when there is part (wiring and plugging elements excluded) failure in the systematic operation or presupposed
system.
Following items should be considered firstly when checking the failure.

wiring failure

open circuit or short circuit of electric wiring

failure in plugging element connection or terminal connection

failure of fuse or maxi-fuse
Notice:
1. The inspection is conducted on vehicle when the system is in operation, therefore, security should be
taken into account when checking.
2. Care should be paid not to make short circuit in the system under the condition that the accumulator is
directly connected, and the applicable voltage should be selected correctly.
Voltage inspection
(a) Verify the voltage situation at the inspection spots.
For example:

Put the ignition switch at
ON
position

Put the ignition switch and SW1 at
ON
position;

Put the ignition switch of SW, SW1 and the relay at

ON
position (SW2 at
OFF
position)
(b) Connect the cathode lead (-) to the normal grounding
place or the cathode terminal of accumulator with the
voltmeter; while connecting the positive lead (+) to the
plugging element or part terminal. Such inspection can
be conducted with the test bubble instead of voltmeter.
Inspection on Conductance and Resistance
(a) Disconnect the terminal or wire of accumulator to guar-
antee there is no voltage between the inspection sports.
(b) Connect the two measuring leads of ohmn meter with the
inspection spots.ohmn meter
SW SW2
electromagnetic coil
relay
SW1

fuse
IG terminal connected to ignigtion
switch of SW
12
0
0


V
Body Electric System
Brief Introduction

BE-5
If there is diode in the circuit, connect the two leads in reverse
polar and make another inspection. When the cathode lead (-)
is connected with the positive (+) side of diode, and the
positive (+) lead should be connected with the cathode (-) lead
of diode, the diode should conduct, while the two leads
connected to the reverse polar, the diode should not contact.
Remark: the specification may be not same due to different
testing meter types; therefore, the application instruction for
testing meter should be referred before the inspection.
Check the light emitting diode (LED) according to the same
approach for diode inspection.
Remark:
The testing meter should be used the one with 3V voltage or the
one has larger resistance than that in circuit.
If no suitable testing meter is applied, the voltage of accumu-
lator may be added to check the LED to see whether it is
lighted.
(c) Use the voltage or ohmn meter with high-impedance
(min voltage of 10 KV) to diagnose the failure in electric
circuit. Body Electric System
Brief Introduction0

0

K

K
ohmn meter
diode
0
0
K

K





ohmn
LED
digital type
analogue type


DCD
C
V
LG terminal of ignition switch
testing bubblefuse box
short circuit

SW1
short circuit

disconnection
electromagnetic
coil
short circuit

disconnection disconnectiong
Check to see whether there is short circuit
(a) Tear down the burned fuse and remove all loads from
the fuse.
(b) Connect the testing bubble at the fuse position;
(c) Verify the situation of testing bubble position:
For example:

Put the ignition switch of SW at
ON
position;

Put the ignition switch of SW and SW1 at
ON
position;

Put the ignition switch of SW, SW1 and Relay at

ON
position (which connects with the relay), and put
SW2 at
OFF
) position (or disconnect the SW2).
(d) Disconnect or re-connect the plugging elements when
observing the testing bubble. In case the testing bubble
keeps lighting, which shows there is short circuit between
the plugging elements; if the testing bubble extinguishes,
there is short circuit between the plugging elements.
(e) Shake the trouble wire alongside the body to locate the
SW2 electromagnetic
coil

BE-8Body Electric System
Protective Box Position and Content
Content of Protective Box
1 protective box I
fuse
1.Small lamp 10A
2.Rain brus 20A
3.Ceiling lamp 10A
4.(Cigarette lighter) 15A
5.Back -u 15A
6.Brake 10A
7.electric window 30A
8.Instrument 10A
fuel delivery/break electromagnetic valve10A(diesel

9.Central control lock 15A Dr
A
B
C



1
2
3
456
789
SL SK
U
N
O
V
P
Q
R NM
NN
NO
S
T NP
NQ
FUSE
1. Protection 10A
2. Unload
3. Charging 10A
4. Back-up 10A
5. ECU 10A
6. Unload
7. Rain wiper 10A
8. Stop lamp 10A
9. Ceiling lamp 10A
10. Central control lock 15A
11. Dual flasher 10A
12. EC 10A
13. Fuel pump 10A
14. Cigarette lighter 15Arelay
A electric window relay
B. small lamp relay
C.(flasher)

(plugging elements of ceiling
lamp wire harness)

(plugging elements of wire
harness in engine room)

BE-9Body Electric System
Protective Box Position and Content
fuse relay
1. Small lamp 10A A. electromagnetic fan relay
2. Brake 5A B. lasher
3. Ceiling lamp 5A C. electromagnetic fan relay
4. Central control lock 15A D. small lamp relay
5. Electric rocker gear 30A E. electric window relay
6. Dual flasher 10A
7. Cigarette lighter 15A
8. Rear vision mirror 5A (1) plugging elements of ceiling lamp wire harness
9. Unload (2) plugging elements of wire harness at front left door
10. Acoustic device 15A (3)plugging elements of wire harness in engine room
11. Rear window 20A
12. Electromagnetic fan 10A
13. Instrument 5A
14. Back-up lamp 5A
15. Rain brush 10A
16. Steering 5A
17. Unload
18. Unload




A
B
C
E D
123 456
78 9 101112
13 14 15
16 1718
SF
Protective bos I (continued)

BE-12
Protective box II
Body Electric System
Protective Box Position and Content
Dr SF
Fuse Vehicle Relay vehicle
1. Front fog lamp 15A Dr A. electromagnetic fan relay Dr
Unload SF charging relay Dr diesel
2. Electromagnetic fan 15A Dr electric horn relay SF
ECU1 10A SF B. large lamp Dr SF
3. Large lamp 10A Dr C. frost relay Dr SF
Horn 15A SF
4. Horn 15A Dr
Lower beam 10A SF
5. ECU1 10A Dr (1) plugging elements of
wire harness in engine room Dr
Charging 10A Dr diesel none SF
Rear frost 5A SF (2) plugging elements of
wire harness in engine room Dr SF
6. Large lamp 10A Dr (3) plugging elements of
wire harness in engine room Dr SF
ECU2 10A SF
7. Rear frost 10A Dr
Upper beam 10A SF
8. ECU2 10A Dr
Preheating 10A Dr diesel
Front fog lamp 10A SF
9. Fuel pump 10A Dr SF
Unload Dr diesel





A
B
C 12 3
45 6
78 9

BE-33Body Electric System
Combination Instrument
Electric circuit diagram (continued)
SF
A3 connected
with negative pole
A1 connected
with positive pole
B8 connected
with negative
pole
B7connected
with positive
pole
A4 connecting
with lighting
switch
A6 connected
with negative
pole
pressure-regulating
potential deviceirect-current
power supply
5-9Vdrive power
supply
110VEL
luminous
plate
left turn indicating lamp
right turn indicating lamp
upper beam indicating lamp
rear fog lamp indicating lamp
rear window/defroster indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
connected with sensor
connected with revolution signal
speedometer
digital clock
fuel gaugeconnect to the cathode of sensor
connected with sensor anode
connected with sensor
connected with sensor
back door indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp75
B9
B2 A15 B1 A9 B11 B10
A14 B4 B6 A12
B14 connected
with positive
pole
B7 connected
with positive
pole
A11 A5A7 B12B5 B13 A16A13 B16 B15
A2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
In this drawing, A stands for the white plugging
elements, B for black plugging elements, they
use the same numerical order.
instrument
plugging element

BE-36Body Electric System
Combination Instrument
Normal indicating range of combination instrument indicator
Speedometer
Real speed Km/h
Displayed speedKm/h
20 40 60 80 100 120 140 160
20
340
056005
Tachometer SY SL
800510005120061400716008
750 1000 2000 3000 4000 5000 6000
750
-10+201000-10+502000
120 3000
150 4000
200 5000
250 6000
300 Real rotating
speedr/min
Displayed rotating
speedr/min
Tachometer Dr SL SK SF
1000 2000 3000 4000 5000 6000 7000
1000
100 2000
200 3000
150 4000
200 5000
250 6000
300 7000
350 Real rotating
speedr/min
Displayed rotating
speedr/min
c. The inaccuracy display of tachometer is usually caused by the interior failures of tachometer, in such situation,
change the combination directly. As for the good-bad shift or out-operation of tachometer, the failures can be judged
according to the following approaches:
1) Start the vehicle, then check the voltage of signal input of tachometer (wire harness with multi-meter, the
voltage should be 6 V or so.
2) In case there is no signal voltage, check the power supply system of the whole vehicle to remove the failures
in circuit.
3) The plugs of wire harness is only allowed to be inserted in the combination instruments under the condition
that the signal voltage is normal, and the instrument is in normal operation.
4) Where the instrument is in abnormal operation, such trouble is caused by the failure of combination
instruments, in such case, change the combination instrument directly.
d. Troubles of fuel gauge and water thermometer
1) In case the instrument indicator points to the large number after it is powered, disconnect the sensor from the
plugging elements of wire harness before judging such kinds of troubles, if the indicator is still at large number,
it can be make a judgment that the trouble is caused by the interior failure of instrument, in such case, change
the combination instrument directly; if the indicator returns to the small number, according to which it can be
judged that the trouble is caused by the sensor failure, therefore, change the sensor directly.
2) where the instrument indicator stands still, such trouble may be caused by three causes probably, interior failure
of sensor, plugging elements of wire harness or interior failure of instrument; the inspection may be conducted
according to the following approaches: disconnect the plugging elements of wire harness from that of sensor,
grounding the wire at the sensor end; in such condition, the indicator should move upwardly to the largest
number; if such phenomena occurs, it can show the trouble is caused by the interior failure of sensor, in such
case, change the sensor directly; if the instrument indicator is still immobilized after it is powered, it can be
judged that the trouble is caused by the interior failure of instrument under the condition that the wire harness
and plugging elements are normal, in such case, change the combination instrument directly.
Fuel gauge Dr SF SY
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

5
4+3
Fuel gauge SJ
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

12
4
2
Fuel gauge SL SK
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
120 45 17

10
10
10

BE-38Body Electric System
Backup Radar System
Inspection on Common Trouble
Failure Judgment Methods
No backup radar display (no
system start notification when
the reverse gear is engaged)Check whether the plugging elements of power supply
of back up radar control box are in well connection as
shown in drawing H in next page.(when the reverse
gear is engaged, touch the detector, if there is vibration,
which shows the detector is powered.
Check whether the wire harness of inner mirror in
electric room and that on the top of body are in well
connection as shown in the drawing A in next page
Check whether the wire harness of back up radar
control box is well connected with that of chassis
and that on the top of body.
Rotate the vehicle key to the ACC position and
engage the reverse gear, then measure to see whether
the back up power supply reaches to 12 V with the
multi-meter of 50 V of voltage, refer to the
red
and black
positions shown in the drawing in next
page.
If the voltage reaches 12 V, change the backup
radar control box in trial firstly, then the inner
mirror in electric room, finally change the roof
wire harness and the chassis.
No backup radar display (but
there is start notification when
the reverse gear is engaged)
remark: such trouble occur
under the blocking condition.Check whether the power supply of back up radar
is well located, see the red and position in the
drawing of next page.
Check and align the plugging element.Poor properties of ultrasonic wave
Change the ultrasonic detector heads.
Continuous back up radar red
lamp alarming (remark: there
is no obstacle within 0.5 m away
from the detector head)Check whether the detectors in the two circuit of
back up radar control box is well plugged, see the
marked positions F, G in the drawing of next page.
Check and well connect those plugging elements
Poor connection of the left/right ultrasonic detector head
Poor performance of back up radar control box.Check and well connect those plugging elements
Change the ultrasonic detector head
Change the back up radar control box.
Vehicle modelpc
Alarming by mistake
The rear standby tire is removedConduct the inspection operation for the rear
standby tire at the spacious place
fail to detect the obstacle
The detector head doesn
t workChange the detector head
There is dirt on detector headClean the detector head
Rear standby tire inspection1. engage the reverse gear for five times repeatedly within ten seconds at the spacious place so that the red
lamp on the screen flash three times, the system will automatically remember the standby tire status.
2. When the body height varies or the stand by tire is opened, make a new inspection for the rear stand by
tire to ensure the backup radar in normal operation.
Seven section of lamp display
Column I
1.49m-1.3m Column II
1.29m-1.1m
Column III
1.09m-0.9m Column IV
0.89m-0.75m
Column V
0.74m-0.6m column VI
0.59m-0.45m
Column VII

0.45m
Remark: the right and left LED display the direction and distance of obstacle respectively for driver
reference.If the voltage fails to reach 12 v, check the power
supply system of original vehicle
s large wires
to restore the voltage to 12 V.
Vehicle model SL SK
fail to detect the obstacle
Trouble description Repairing and treatment approaches

BE-61
Acoustical equipment system
The devices in this series is the vehicle-equipped acoustical receiver and recorder whose function is realized through
the electronic tuner and CD recorder, therefore, it can receive the amplitude modulation, frequency modulation and
stereo broadcast and can record the CD disc, what??s more, it is with the advanced electric anti-quaking, strong capability
of error correction, fashionable blue LCD liquid crystal digital display, and four-way power output. The device in this
series also has the characteristics such as low distortion, large output power and good performance of anti-interference,
broad frequency range and sweet sound, etc.
Diagram of Acoustical equipment system
SF
fuse
ignition switch
ACC ON ST
side-window aerial
CD deviceloudspeaker
ignition switch CD plugging elementplugging elements of rear
loudspeaker of CD device
1 2 3 4 5
6 7 8 9 1012 34
56 78912
34 5 5
4
1 2
3 5 3
8
4
9
75
6
1
7
Note: For Dr the antenna is the rod type.
battery cigarette lighter left front
right frontleft rearright rear
from small lamp relay
2
amplifier
Body Electric System
Acoustical Equipment System