wheel GREAT WALL SAFE 2006 Owner's Manual

SA-4Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)
5. Adjustment for inner tilt angle of kingpin, outer tilt angle
of front wheel and back tilt angle of kingpin
Item
Inner tilt
angle of
kingpin
Outer tilt
angle of
front
wheelApplicable vehicle type
Dr SL SK SY
SJ
Mechanic
steeringDr SL SK SY
Power
steeringDr
SL SK SY
SJ
Back tilt
angle of
kingpinMechanic
steeringDr SL SK SY
Power steer-
ingDr SL SK SY
SJ9
30
45

14
52

0
30
20

0
10
10

0
20
10

0
30
15

2
45
15

3
15
Location parameter
4. Adjust the wheel angle
Take apart the limit bolts of the steering knuckle to check the
steering angle A of inner wheel.
Inner wheel steering angle
Dr SL SK SY
( 36
40
)
SJ
( 32
34
)
Remark: The wheel should not contact the body or brake hose
when the steering wheel reaches the limit position.
In case the steering angle of inner wheel doesnít conform to the
standard value, adjust the wheel angle through adjusting the
limit bolts of the steering knuckle.
Fastening torque
(90
0)N
m(SJ)
If the wheel angle fails to be adjusted within the standard value,
change the weary or damaged parts of steering system.
If the tilt angle fails to fall within the specified values, make an
adjustment through adding or reducing the gaskets on the
location of upper arm.
Gasket thickness: 3.0, 2.0 and 1.0mm
Once the gasket thickness increases by 1mm, the outer tilt
angle of wheel will change by 7', while the back tilt angle of
kingpin will change 20'.
After the wheel outer tilt angle and the back tilt angle of kingpin
are adjusted, if the inner tilt angle of kingpin still fails to the
specified value, check the steering knuckle or front wheel to
see whether they are bending or loose.
1
50
-20

adjusting bolt
outer tilt
angle of
front wheel inner tilt angle of kingpin
back tilt angle of
kingpin
front AB AB
HPM

SA-5
7. Check the sliding measuring situation.
Check the sliding situation with the sliding measuring tester.
Sliding measuring value:
.5m/km
push forward the vehicle;
forward
A=BB A
6. Wheel toe-in adjustment
(a) Verify that each wheel has been located forward in a line.
(b) Mark the tire center at the bearing height on the tread of
left and right tire, and measure the distance between the
marks on left and right treads.
(c) Push forward the vehicle until the mark on the back tread
of tire moves to the front.
Remark: the toe-in measurement should be conducted from the
same spot at the same height.
(d) Measure the distance between the two marks on the front
of two treads.
Toe-in value: (0-2)mm
(e) Loosen the clamping bolts of connecting pipe.
(f) Adjust the toe-in angle through the approach according to
which rotate the left and right drag rod tube by a same
angle.
Remark: check the lengths of the two drag rods to see whether
the two rods are same in length.
Length error of the left and right drag rod should not
be larger than 2.0mm.
(g) Tighten the clamping bolts.
Fastening torque
(20
) N
m
(h) Locate the split pin well.
Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)

SA-6Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF)
Alignment of Front Wheel
(SF)
1. The following items should be checked to remove the
troubles.
(a) Check the tire abrasion and the air inflation to see it is
suitable or not.
Tire inflation pressure: (250
0)kPa
(b) Check the front wheel bearing to see whether it is loose.
(c) Check the front suspension to see whether it is loose.
(d) Check the steering driving device to see whether it is
loose, and
(e) Check the front vibration through elastic force test to see
whether it is normal in performance.
2. Height adjustment of vehicle
Adjust the vehicle height to the standard value so as to make
the Alignment of Front Wheel inspection.
A-B-58 5mm
A: The height of steering knuckle shaft center.
B: The center height of the adjusting cam bolt at front end
The standard value for the unloaded height is: the
difference of the center height of drive shaft climax and
the front adjusting cam bolt is 58.5mm.
3. Mount on the four wheel locating device
This approach should be conducted according to the detailed
instruction of the equipment manufacturer.
4. Adjust the outer tilt angle of front wheel and the back tilt
angle of kingpin
The outer tilt angle of front wheel: 0
5'
0'
The back tilt angle of kingpin: 2
0'
0'
Outer inclination of front wheel:
BA
the outer tilt angle of
front wheelthe back tilt angle
of kingpin
front

SA-7Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF)
In case the outer tilt angle of front wheel or the back tilt angle
of kingpin fails to conform to the specified value, adjust the
cam forward or backward may amend them.
5. Wheel angel adjustment
Take apart the limit bolt cap of the steering knuckle to check
the inner wheel steering angle A.
The inner wheel steering angle: =32

Notice:The wheel should not touch the body brake hose
when the steering wheel is rotated to the bottom.
In case the max steering angle is not in the conformity with the
standard value, adjust the wheel angle through the limit bolts
of steering knuckle.
In case the wheel angle still fails to fall within the standard
range, make a inspection and change the weary and damaged
steering mechanism parts.
6. Wheel toe-in adjustment
Adjust the wheel toe-in according to the following approach
(a) Raise or reduce the vehicle until the suspension stands in
balance.
(b) Push the vehicle on the ground 5 meters forward under
the condition that the front wheels locate forward in a
line.front cam adjustment
rear cam adjustment
reduce increaseincrease reduce
A
B
A B
front

SA-8Suspension System and Automobile Axle
Alignment of Front Wheel (SF)
(c) Mark the center of the back of front wheel, and measure
the distance ìBî between the remarks on the left and right
tires.
(d) Push the vehicle forward so that the mark on the back of
tire moves to the measuring height of the instrument.
Remark: if the tire moves too far, repeat the approach (b).
(e) Measure the distance ìAî between the marks on the front
of tire.
(f) Measure the wheel toe-in.
Toe-in = B-A
Inspection standard: (0-2)mm
In case the toe-in fails to conform to the specified value, it can
be amended through adjusting the left and right drag rods.
(g) Loosen the clamping bolt and nut.
(h) Adjust the toe-in situation by the approach of rotating the
left and right drag rod by a same angle.
(i) Ensure the left and the right drag rods are same in length.
B
forward
move the vehicle forward
A
front
A
B
A=B

SA-9Suspension System and Automobile Axle
Alignment of Front Wheel (SF)
(j) Tighten the clamping bolts and lock them with split pin.
Remark: the clamping bolt should face the front of the vehicle.
(k) Side-slip inspection
Sideslip: =5m/km
front

SA-10
Front wheel hub and steering knuckle
Element Drawing
front wheel hub snap ring
25-28

front wheel hub oil seal
brake caliper
plain washer
bearing 32007
front wheel hub and
front brake discbearing 30205
locking nut
front wheel hub cap
stop washer
dust cover


steering knuckle arm
steering knuckle 85-105
98-118

100-120
132-152





Used component which can not be used any more
N
m: specific torque
Dr
front brake shell
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle

SA-11
4. Take apart the front wheel hub oil seal, the inner race and
roller assembly of bearing 32007.
(a) Pry out the oil seal.
(b) Take out the bearing inner race and roller assembly.
Front Wheel Hub
Disassembly of Front Wheel Hub
1. Take apart the brake caliper.
2. Take apart the front wheel hub cap.
3. Take apart the front wheel hub and front brake disc:
(a) Take apart the split pin to take down the lock cover.
(b) Screw off the lock nuts of the hub bearing with spanner
and take down the stop washer.
(c) Take apart the front wheel hub and front brake disc with
the bearing 30205 together.
Disassembly the wheel hub and suspend it with tightwire.
Remark: Donít dismantle the brake hose and brake metal pipe
Takeapart the front wheel hub cap from the gap between the
front wheel hub cap and the front wheel hub.
5. Bearing outer race inspection and tear-down
(a) Inspect the bearings
Clean each bearing and check them to see whether there is wear
or damage.
(b) Take apart the bearing outer race
Tap out the bearing outer race with copper bar and hammer.
Notice: bind the disassembled inner and outer bearing
race together to avoid of mixing.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-12
6. Inspection and replacement for front brake disc
(a) Check the wear situation of the front brake disc. (see Dr
the brake caliper).
(b) Use the spanner to tear down the bolts that connect the
front wheel hub and the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolt and spring washer, and screw up the bolts with a
moment spanner to the specified torque in the diagonal
order.
Fastening torque
(60-79)N
m
(d) Conduct the equilibrium test on the dynamic balancer,
the amplitude value displayed should not be larger than
13.5g under the condition that the measuring rotating
velocity is 796 r/m and the locking rotating velocity is
786 r/m, when the amplitude value is larger than 13.5 g,
encase the counter balanced clip, which is 4 g each, at the
corresponding phase, the number of the clip encased
should not be more than four.
7. Bearing outer race change
Press in the new bearing outer space with the special service
tools.
Notice: the bearing inner and outer races should be changed at
one time.
Assembly of Front Wheel Hub
1. Mount on the Bearing 32007 inner race and roller assem-
bly as well as the front wheel hub oil seal.
Coat the lithium base grease of (4-5)mm on the inner surfaces
of bearing outer race and the front wheel hub, encase the
Bearing 32007 inner race and roller assembly, plaster the
lubricant again. Coat a little lubricant on the lips of front wheel
hub oil seal and then tap it in place.
Notice: do not make the lubricant contact the front brake
disc face.
2. Mount on the Bearing 32007 inner race.
After coating the bearing outer race with the lithium base
grease of 4-5 mm, encase the inner race and roller assembly of
Bearing 30205, and plaster the lubricant again.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-13
3. Mount the front wheel hub on the steering knuckle.
Coat a little lubricant at the position of the steering knuckle
where the oil seal locates, mount the front wheel hub and front
brake disc on the steering knuckle, and then mount on the stop
washer.
4. Preload adjustment
(a) Mount on the lock nut and screw up according to the
specified torque.
Fastening torque
(130-150)N
m
(b) Run the front wheel hub about 1/4-1/3 of circle, and
combine it with the bearing seat.
(c) Loosen the locking nut to ensure the front brake disc run
freely, and then screw up the nuts to the specified torque.
Fastening torque
(25-35)N
m
(d) Hook the front wheel hub with the spring-tension meter
and pull the spring-tension meter slowly in the tangential
direction of this spot.
The reasonable range of tension force: (16-33)N.
Remark: if the tension force is larger or smaller of the reason-
able range, screw up the nuts again until the tension force falls
within the reasonable range.
(e) Measure the bouncing value of the front brake disc,
which should not be larger than 0.11mm.
5. Mount on the lock cover and the split pin
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)