wheel bolts GREAT WALL SAFE 2006 Owner's Manual

SA-43
Mount of Upper Arm
1. Screw up the axle nut of upper arm according to the
specified torque;
Fastening torque
(225
)N
m
2. Mount on the upper arm;
Screw up the three bolts of the upper swing arm shaft according
to the specified torque;
Fastening torque
(178
5)N
m
3. Connect the upper arm ball stud with the upper arm;
Use four sets of bolt and nut to connect the upper arm ball stud
and the upper arm.
Fastening torque
(27
)N
m
4. Mount the torsion rod spring;
5. Check the Alignment of Front Wheel:
(See Page SA-6)
Suspension System and Automobile Axle (SF/2WD)
Front Suspension \(Lower arm, Guide Lever and Transverse Stabilizer Rod)
Guide Lever
(See page SA-26)
Transverse Stabilizer rod
(See page SA-27)

SA-46
5. Tear down the front hub, the oil seal and the inner race
of front hub bearing (inner)
(a) Prize out the oil seal.
(b) Take out the inner race of front hub bearing (inner).
6. Inspection on and change of the outer race of front hub
bearing
(a) Check each bearing:
Wash the inner and outer races of each bearing to check
their wear or damage situation.
(b) Tear down the outer race of each bearing:
Tap out the outer bearing race with copper bar and hammer.
Notice: bind the inner and outer races of the same
bearing together to prevent from mixing.
7. Inspection and change for front brake disc
(a) Check the wear situation of the front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolts, which are tightened diagonally with moment span-
ner according to the specified torque.
Fastening torque
(70-80)N
m
(d) Make the dynamic balance test on the dynamic balancer,
and the amplitude value displayed should not be smaller
than 13.5g under the condition that the measuring rotat-
ing velocity is 796 r/m and the locking rotating velocity
of 786 r/m, otherwise, tap the counter balanced clip,
which is 4g each, in the corresponding position, the clip
number should not be more than 4.
(e) Tap in the new bearing outer race carefully with the
special service tool.
Notice: the inner and outer races of the same bearing
should be changed in one time.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-48
(e) Hold the bolt of front wheel hub with the spring-tension meter
and drag slowly in the direction of the spot tangent line.
Suitable tension range
(29-54)N
The nut should be screwed up again within the suitable range if the
tension value is overlarge or over small.
(f) Check the bearing to ensure it cannot leap excessively (the
axial clearance should not be more than 0.05mm).
(g) Measure the bouncing value of the front brake disc, which
should not be more than 0.11mm, and
5. Mount the liner and the free hub:
(a) Tear down the free wheel hub cap firstly.
(b) Mount the liner and the free hub on the front wheel hub.
Fastening torque
(25-29)N
m
(c) Mount on the free wheel hub cap.
Fastening torque
(6-12)N
m
6. Mount the brake caliper:
(a) Mount the brake caliper on the steering knuckle and screw
up the bolts according to the specified torque.
Fastening torque
123N
m
(b) Connect the Bundy tube.
Fastening torque
20-22N
m
7. Check the height of brake liquid level and, if required, add
the brake liquid, exhaust the gas from the brake system.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)
(h) Bend one tooth of lock plate inside and other teeth outside
so as to lock the steering knuckle nut.

SA-52
8. Mount the inner oil seal óon the steering knuckle.
Check the oil seal visually, if any deformation or glue lack is
found, change the oil seal
Mount of Steering Knuckle
1. Mount the lower ball stud on the steering knuckle;
Connect the lower ball stud and the steering knuckle with
bolts, and screw up the bolts according to the specified torque.
Fastening torque
(70-90)N
m
2. Mount on the steering knuckle
(a) Coat the lubricant HP-R on the drive shaft.
(b) Press down the lower arm to mount on the steering
knuckle.
(c) Mount on the groove nut of lower ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
(d) Mount on the groove nut of upper ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-81
4. Check the grooved ball bearing
Check the grooved bearing to see whether there is damage or
wear.
5. Change the bearing where necessary:
(a) Press out the grooved ball bearing with SST.
(b) Press in the new grooved ball bearing with SST.
6. Mount the new oil seal of rear wheel bearing.
Press in the new oil seal of rear wheel bearing with SST
Coat moderate lithium base grease on the lip open of oil seal.
7. Check the bearing seat.
Check the wear or damage situation.
8. Change the bearing seat where necessary:
(a) Tear down the oil seal of rear wheel bearing and the
grooved ball bearing with SST.
(b) Tap the bolts with copper bar to tear down the bearing seat.
(c) Mount the new grooved ball bearing and the oil seal of
rear wheel bearing on the bearing seat
(d) Press the rear brake, which is put on with bolts, in the
bearing seat.
9. Check the wear or damage of the inner oil seal of the rear
wheel bearing.
10. Change the rear wheel bearing where necessary:
(a) Tear down the oil seal of rear wheel bearing with SST. Suspension System and Automobile Axle (rear)
Rear half Axle Shaft

SA-100Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type)
Remark: Tightening U-shaped bolt to the degree that the
protruding lengths of all U-shaped bolts under the spring seat
are the same.
3. Mount the rear vibration damper
(a) Connect the vibration damper to the vehicle frame with
bolts and then tighten the bolts.
Tightening moment: (25
)N
m
(b) Connect the vibration damper to the sprint seat with bolts
and tighten these bolts.
Tightening moment: (25
)N
m
4. Keep the suspension frame in stable status;
(a) Mount on the wheel;
(b) Remove the bracket, and make the vehicle bounce verti-
cally for several times so as conduce it in stable status.
5. Tighten the front ear pin and rear ear pin;
Tighten the nuts of front ear pin;
Tightening moment: (90
0)N
m
Tighten the nuts of rear ear pin;
Tightening moment: (90
0)N
m
all lengths of bolts protruding are same

BR-3
Troubleshooting (continued)
Braking System
Notice and Troubleshooting
Trouble Causes Inspection items
There is clatter noise when using
the brake(Drum-type brake)
The brake shoe is seized on the flange of rear baffle;
The flange of rear baffle is worn;
The pressure spring of brake shoe is loose or missing;
The fixed bolts of brake bottom plate is loose;
(disc type brake)
The brake pad support plate is loose or missing
The mounting bolts are loose;Add lubricant
Change the lubricating flange
Change
Tightening it
Change
Tightening it
There is hoarse noise or quack-
quack when using the brakeThe brake shoe or brake pad is worn;
The brake caliper, the wheel or the rotator interferes each
other.
There is friction between the dust cover and brake disc,
the brake bottom plate and the brake drum;
The other braking part has trouble
There is friction between the tire and bodyChange the part, and re-process
precisely the brake drum or
rotator if the abrasion is serious;
Make change according to real
situation;
repair or change
Make repairing according to
real situation;
Change
Check or maintain the part
There is such noise as
continuous screaming, quack-
quack, oscillating sound, etc.
Notice: the braking materials
may generate the natural noise
and heat during friction, and
thus emit the energy. Therefore,
it is normal to have the
screaming noise. These
phenomena will be more serious
under the condition of frigidity,
torridity, and over humidity,
snowing and mud. the
screaming noise occurring
occasionally will not lead the
fatal brake trouble nor reduce
the effective properties of the
brake.The brake drum, brake liner, liner or brake pad is worn
or scraped
The brake liner or brake pad is dirty or with oil stain or
polished.
The brake liner or brake pad is improperly used.
The brake pedal or vacuum booster drag rod is unsuitably
adjusted.
(disc type brake)
The brake pad silent pad is loss or damaged;
The brake pad is worn to the degree that the abrasion-
indicating lamp of brake pad has friction with the rotator.
There is burr or rust on the brake caliper.
(Drum type brake)
The pressure spring of brake shoe is soft in rigidity, or is
damaged or unsuitable.
The pressure spring pin or spring of brake shoe is loose
or damaged;
There is crack on the brake bottom plate flangeCheck, repair or change
Clean or change
Check or change
Check for adjustment
Change
Change
Clean or polish the burr
Check, repair or change
Check, repair or change
Check, repair or change

BR-14
Brake pad change
Remark: Check the thickness of the friction material of brake
pad through the observation hole on caliper body after the
vehicle covers thirty thousand; if the thickness fails to fall
within the specified range, change is required. (If the brake is
used often, the thickness of friction materials of brake
pad is required to check whether it is within the specified
range after the vehicle covers more than ten thousand,
if not, change it.
1. Tear down the front wheel;
2. Check the thickness of friction material of brake pad:
Check the thickness of friction material of brake pad through
the observation hole on caliper body, if it fails to be within the
specified range, change it.
Min thickness: 2.0mm
3. Raise the wheel-brake cylinder:
(a) Tear down the short bolts of sliding sleeve;
(b) Uplift the wheel brake pump and hang it with rope to
protect the brake oil pipe.
Remark: Do not loosen the brake oil pipe and the bleeding plug.
4. Tear down the following parts:
(a) Two braking pads;
(b) Two silent pad clusters;
(c) Four braking pad lock plates.
Braking System
Front Brake (Dr)

BR-15
5. Brake disc measurement
(See page BR-17)
6. Measure the radial run-out of the brake disc;
(See BR-18)
7. Mount the lock plate of brake pad.
8. Mount the new brake pad.
(a) Mount the silent pad cluster on brake pads of both the
inner and outer sides;
Remark: Pollution of oil stain or coat is not allowed on the
work faces of brake pad or brake disc.
(b) Draw out a little brake liquid from the liquid container to
prevent the brake liquid overflowing from the liquid
container;
(c) Press in the piston with the hammer lever or similar tool.
9. Mount the wheel-brake cylinder;
Mount and screw up the hex bolts (the hex bolts shall be coated
with the thread locking sealing agents.
Fastening torque
(38-50)N
m
Remark: only one brake pad can be changed in one time so as
to prevent the piston of other wheel being shot out.
Braking System
Front Brake (Dr)

BR-16
10. Mount the front wheel;
Screw up the fixing nut of wheel.
Fastening torque
(135
150)N
m
Disassembly of Wheel-brake Cylinder
1. Take apart the brake pipeline.
(a) Tear down the brake pipeline. And block the outlet with
a clean cork.
(b) Tear down the brake oil pipe bracket from the wheel-
brake cylinder.
2. Tear down the wheel-brake cylinder from the caliper
bracket.
Tear down the two hex bolts and the wheel-brake cylinder.
3. Tear down the brake pad:
(a) Two brake pad;
(b) Two silent pad cluster;
(c) Four brake pad lock plate.
Pump Disassembly of Wheel brake
1. Take apart the following parts:
(a) Two sliding sleeve;
(b) Four sliding sleeve dust cover;
(c) Two sliding liner.
Braking System
Front Brake (Dr)