HONDA ACCORD COUPE 2004 CL7 / 7.G Owners Manual

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the south side of an
east/west mountain road with a
mountain on the south side of the
road.
Driving on the north side of a
large commercial truck on an
east/west road
Driving in the tunnels If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the CD/SAT
button. A variety of music types and
styles will play.
There may be other geographic
situations that could af f ect satellite
radio reception. Driving on a single lane road
alongside dense trees taller than
50 f t. (15 m) to the south of you
Driving on the lower level of a
multi-tiered road
Driving on a road beside a vertical
wall, steep clif f or hill to the south
of youAs required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
Comf ort and Convenience Feat ures
Receiving Satellite Radio Service
Playing t he XMSatellite Radio
132
——y
y
(%
y
y

If you decide to purchase XM
Satellite Radio service, contact XM
Radio at www.xmradio.com, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number.
To get your XM Satellite radio ID
number:Af ter you have registered with XM
Radio, keep your audio system in the
SAT Radio mode while you await
activation. This should take about 30
minutes.
While awaiting activation, make sure
your vehicle remains in an open area
with good reception. Once your
audio system is activated, ‘‘category’’
or ‘‘CH’’ will appear in the display
and you will be able to listen to XM
Radio broadcasts. XM Radio will
continue to send an activation signal
to your vehicle for at least 12 hours
from activation request. If the
service has not been activated after
36 hours, contact XM Radio.
Turn the TUNE knob or press the
TUNE bar until ‘‘0’’ appears in the
display. Your ID number will appear
in the display.
Comf ort and Convenience Feat ures
Playing t he XMSatellite Radio
133
——y
y
(%
y
y

Playing a CD
Comf ort and Convenience Feat ures134
PWR/VOL KNOB
PWR/VOL KNOB
AM/FM BUTTON
CD SLOT
CD LOAD INDICATOR CD BUTTON
PRT BUTTON
CD SLOT
LOAD BUTTON RDM
BUTTON
EJECT BUTTON
EJECT BUTTON TRACK NUMBER
RDM
BUTTON
RPT BUTTON
CD BUTTON
SEEK/SKIP
BAR CD LOAD
INDICATOR
DISC AND TRACK NUMBERS
SEEK/SKIP
BAR
LX model
EX and LX-V6 models
——y
y
(%
y
y

CONT INUED
Comf ort and Convenience Feat ures
Playing a CD
135
PWR/VOL KNOB
CD SLOT
CD BUTTON
PRT BUTTON
CD SLOT
LOAD BUTTON RDM
BUTTON
RDM
BUTTON
CD BUTTON
SEEK/SKIP
BAR
EX-L and EX-V6 models
(Canadian Vehicles only)
SEEK/SKIP
BARDISC
NUMBER
CD LOAD INDICATOR
LOAD BUTTON EJECT
BUTTON
CD LOAD INDICATOR
RPT BUTTON
EJECT
BUTTONEX-L and EX-V6 models
without Navigation System
(U.S. Vehicles only)
DISC AND TRACK NUMBERS TRACK NUMBER
PWR/VOL KNOB
——y
y
(%
y
y

Playing a CD
Comf ort and Convenience Feat ures136
PWR/VOL KNOBUPPER DISPLAY
DISC AND TRACK NUMBERS
CH/DISC BARCD SLOT
EJECT BUTTON
RANDOM ICON
LOAD BUTTON
CD/SAT BUTTON
SCAN BUTTON
DISC
RPTICON TRACK
RPTICON
DISC
SCANICON
TRACK
SCAN ICON
SEEK/
SKIP BAR
CD
LOAD INDICATORAUDIO DISPLAY BUTTON
EX-L and EX-V6 models
with Navigation System (U.S. Vehicles only)
——y
y
(%
y
y

To load or play CD’s, the ignition
switch must be in the ACCESSORY
(I) or ON(II) position.
You operate the CD player/CD
changer with the same controls used
for the radio. To select the CD
player/CD changer, press the CD
button. The number of the track
playing is shown in the display. With
the in-dash CD changer, the disc and
track numbers are displayed. The
system will continuously play a CD
until you change modes.
Insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way to play it. When the system
reaches the end of the disc, it will
return to the beginning and play the
disc again.To play the radio when a CD is
playing, press the AM/FM button.
Press the CD button again to switch
back to the CD player.
To play the tape when a CD is
playing, insert a tape in the player
(optional). If a tape is in the player,
press the AUX button. Press the CD
button again to switch back to the
CD player. The cassette player is
optional on all U.S. models.
To listen to satellite radio when a CD
is playing, press the CD/SAT button.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f . Press the LOAD button until you
hear a beep and see ‘‘LOAd’’ in the
display (in the upper display on
vehicles with navigation system).
The disc number/icon f or an
empty position is highlighted and
the red light starts blinking.
Insert the disc into the CD slot
when the green CD load indicator
comes on. Insert it only about
half way; the drive will pull it in the
rest of the way. You will see
‘‘BUSY’’ in the display as the CD
load indicator turns red and blinks
as the CD is loaded.
You cannot load and play 3-inch (8-
cm) discs in this system.
You can also play 3-inch (8-cm) discs
without using an adapter ring. 1. 2. 3.
For vehicles with Satellite Radio
For vehicles with in-dash CD changer
LX model
CONT INUED
Playing a CD
Comf ort and Convenience Feat ures
To Play a CD
137
——y
y
(%
y
y

µ
µ
´
Û
Ý
µ µ
µ
When the CD load indicator turns
green and ‘‘LOAd’’ appears in the
screen again, insert the next CD in
the slot.
Repeat this until all six positions
are loaded. If you are not loading
all six positions, the system begins
playing the last CD loaded.
To select a dif f erent disc, press the
appropriate side of a preset bar (1
6) or use the Preset 5 (DISC ) to
select the previous disc or Preset 6
(DISC ) to select the next disc in
sequence. On vehicles with
navigation system, touch the
appropriate disc icon or press the
or side of the CH/DISC bar. If
youselectanemptypositioninthe
CD changer, the system will try to
load the CD in the next available slot.
Each time you
press and release side, the
player skips f orward to the
beginning of the next track. Press
and release side, to skip
backward to the beginning of the
current track. Press it again to skip
to the beginning of the previous
track. To move rapidly within a track, press
andholdthe or side.
The SCAN function
samples all the tracks on the
selected disc in the order they are
recorded on the CD. To activate it,
press and release the SCAN button.
You will see SCAN in the display.
You will get a 10 second sampling of
each track on the selected CD. Press
the SCAN button again to get out of
the system.
This f unction samples
each f irst track of all the discs in the
in-dash CD changer in the order they
are stored. To activate it, select the
D-SCAN mode by pressing and
holding the SCAN button. You will
see D-SCAN in the display. You will
get a 10 second sampling of the f irst
track on each CD. Press the SCAN
button again to get out of the system.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate side of a
preset bar or touching a disc icon.
The system stops playing the current
CD and starts the loading sequence.
It plays the CD just loaded.
You operate the CD changer with
the same controls used f or the radio.
The numbers of the disc and track
playingareshowninthedisplay.On
vehicles with navigation system,
these numbers also appear in the
upper display.
4. 5.
On vehicles with in-dash CD changer
Except f or LX model
Comf ort and Convenience Feat ures
Playing a CD
For Vehicles wit hout Navigat ionSyst em
SEEK /SK IP SCAN
D-SCAN
138
——y
y
(%
y

y

µµµ
µ
µ
µ
µ
µ
CONT INUED
To continuously replay
a track, press and release the RPT
button. You will see RPT in the
display. Press the RPT button again
to turn it off. When you touch
this icon on the audio display or
press the SCAN button, you will get
a10secondsamplingof eachtrack
on the current CD. You will see
TRACK SCAN highlighted on the
audioscreenandSCANintheupper
display. Press the icon or button
again to get out of the system.
When you touch
the TRACK RPT icon, the system
continuously plays the same track.
You will see TRACK RPT
highlighted on the audio screen and
RPT in the upper display. Press the icon again to get out of track repeat.
When you touch the
DISC SCAN icon on the audio
display, the system gives you a 10
second sampling of the f irst track on
each disc in the in-dash CD changer.
You will see DISC SCAN highlighted
on the audio screen and D-SCAN in
the upper display. Touch the icon
again to get out of the system. When you touch the
DISC RPT icon on the audio display,
the system continuously replays the
current CD. You will see DISC RPT
highlighted on the audio screen and
D-RPT in the upper display. Touch
the icon to turn the feature off.
When you touch the
RANDOM icon on the audio display,
the system plays the tracks on the
current CD in random order. You
will see RANDOM highlighted on
the audio screen and RDM in the
upper display. To turn this f eature
of f , touch RANDOM again or select
a dif f erent disc icon.
To continuously
replay the current disc, press and
hold the RPT button. You will see
D-RPT in the display. Press the RPT
button again to turn it off.
Press and release the
RDM button to play the tracks in
random order. You will see RDM in
the display. Press the RDM button
again to return to normal play.
To use the controls, press the
AUDIO DISPLAY button, the control
icons will appear on the screen.
Except f or LX model
Playing a CD
Comf ort and Convenience Feat ures
REPEAT TRACK SCAN
TRACK RPT
DISC SCAN
DISC RPT
RANDOM
D-REPEA T
RANDOM
For Vehicles wit h Navigat ion Syst em
139
——y
y
(%
y
y

µ
µÛÝ Each time you
press and release , the player
skips forward to the beginning of the
next track. Press and release ,
to skip backward to the beginning of
the current track. Press it twice to
skip to the beginning of the previous
track.
To move rapidly within a track, press
andholdthe or .
Press or to select
an icon and play the disc.
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button. Press the AM/FM button to switch
to the radio while a CD is playing. To
play the CD, press the CD button.
PresstheAM/FMorCD/SAT
buttontoswitchtotheradioor
satellite radio while a CD is playing.
To play the CD, press the CD button
again.
If tape is in the optional tape player,
press the AUX button to switch to
the tape while a CD is playing. Press
the CD button again to switch back
to the CD player.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .To remove the disc currently in play,
press the EJECT ( ) button.
When a disc is removed f rom a slot,
the system automatically begins the
load sequence so you can load
another CD in that position. If you do
not remove the disc f rom the
changer within 15 seconds, the
system returns to the previous mode
(AM/FM or satellite radio). The disc
will reload into the system and will
remainthereinapausemode.
To remove a dif f erent disc f rom the
changer,firstselectitwiththe
appropriate preset bar, or the
appropriate icon or the CH/DISC bar.
When that CD begins playing, press
the eject button. Continue pressing
the EJECT button to remove all the
discs f rom the changer.
On LX model
Except f or EX-L and EX-V6 models in
the U.S.
On EX-L and EX-V6 models in the U.S. Except f or LX model
Comf ort and Convenience Feat ures
Playing a CD
SEEK /SK IP CH/DISC
To Stop Playing a CD Removing CD’s From the In-dash
CD Changer
140
——y
y
(%
y
y

µ´ µ´
You can also eject discs when the
ignition switch is of f . The disc that
was last selected is ejected f irst. An optional six or eight disc CD
changer is available f or your vehicle
f rom your Honda dealer.
This disc changer uses the same
controls used f or the in-dash CD
player/changer or the radio.
Load the desired CDs in the
magazine, and load the magazine in
the changer according to the
instructions that came with the unit.
To select the CD changer, press the
CD button. The disc and track
numbers will be displayed. To select
a dif f erent disc, use the Preset 5
(DISC ) side or Preset 6 (DISC )
side of the preset bar. To select the
previous disc, press the Preset 5
(DISC ) or Preset 6 (DISC ) to
select the next disc in sequence.If you select an empty slot in the
magazine, the changer will search
f or the next available CD to load and
play.
On LX model, if there are no CDs in
the changer, the display will f lash,
and you will have to select another
mode.
Playing a CD
Comf ort and Convenience Feat ures
Operating the Optional CD
Changer
141
——y
y
(%
y
y