Front HONDA CIVIC 1997 6.G Workshop Manual

)Diagnostic Trouble Code (DTC) Chart -'98 - 00 Models
NEC SRS Unit
Ir
SRS indicator lightDTCPossible causeCorrestive actionSee page
doesn't come on
none
(doesn't
come on)
Faulty SRS indicator light circuitTroubleshooting24-26
comes on
none*3
(doesn't
go off)
Faulty SRS indicator light circuit, internal
fallure of SRS unit, faulty SRS power supply
(VB line)
Troubleshooting24-34
No DTC*3(lis ht
comes on
after self-
diagnosis)
Faulty SRS power supply (VA linelTroubleshooting24-39
l-1Open in the driver's airbag inflator
Troubleshooting
24 42
Increased resistance in the driver's airbag
inflator24-42
Short to another wire in the driver's airbag
inflator or decreased resistance24-44
't -4Short to power in the driver's airbag inflator24-46
t-5Short to ground in the driver's airbag inflator24-48
With front passenger's airbag:
Open in the passenger's airbag inflator
Without front passenger's airbag:
Open in the dummv resistor
24-50
24-54
With front passenger's airbag:
Increased resistance in the passenger's airbag
inflator
Without front passenger's airbag:
Increased resistance in the dummy resistor
24-50
24-58
with front passenger's airbag:
Short to another wire in the passenger's
airbag inflator or decreased resistance
Without front passenger's airbag:
Short to another wire in the dummy resistor
or decreased resistance
Troubleshooting
24-52
24,59
2-4
With front passenger's airbag:
Short to power in the passenger's airbag
inflator
Without front passenger's airbag:
Shon to power in the dummy resistor
24-54
24-60
With front passenger's airbag:
Short to ground in the passenger's airbag
inflator
Without front passenger's airbag:
Short to ground in the dummy resistor
24-56
24-61
(cont'd)
24-19
l,

Troubleshooting
The SRS Indicator Light Doesn't Come On (cont'dl
Frcm page 24.21
Ch6ck tho wire h6rn6s of tho SRS indicator light circuir (21:
1. Turn the ignition switch OFF.2. Disconnect the SRS main harness 3P connector from themain wire harness,3. Connect a voltmeter between the No. 1 terminal (+) ofthe SRS main harness 3P connector and ground.4. Turn the ignition switch ON (ll), and measur€ voltage.
13 thore 8.5 V or less for 3ir sacond3 aftgr tho ignitionswitch h.3 b.en turned ON llllT
YESNO
Short to power in tho BLU wi.e of lhe m.in wiro hrnroas;r€orir tho ham6as.
Chock the wi.e harness otthe SRS indicator ci.cuit l3l:1. Turn the ignition switch OFF.2. Disconnect the banery negative cable. th6n the positivecable, and wait three minutes.3. Disconnect the driver's (and front passenger's) airbag con-nector{s} (seo page 24-11).4. Disconnect the SRS main harness 18P connector trom
5. Connect a voltmeter betwo€n the No. 6lerminal {+} ofthe SRS main harness 18P connector and ground.6. Turn the ignition switch ON (ll), and measure vollagg. Thereshould be 0.5 V or less.
ls voltago as specified?
YESNO
Faultv SRS unh; roplic. the unit l!€e paqo 2+76).
Shoft to Dowar in tha BLU wire ot tho SRS mein h.rn.r3:reobce the hrlne3s,
24-2a
SRS MAIN HARNESS18P CONNECTOR
MAIN WIRE I{ARNESS3P CONNECTOR
SRS MAIN I{ARNESS3P CONNECTOR
c802
SRS UNIT
SRS MAIN HARNESS 1AP CONNECTOR
-

)The SRS lndicator Light Doesn't Go Off -'96 - 97 Models
CAUTION: Whenever the ignition switch is ON (ll), or has been turned OFF for less than three minutes, be careful not to
bump the SRS unit; the airbag{sl could accidentally deploy and cause damage or iniuries
Try to reproduce lhe SRS indicator light:
1. Erase the DTC memory (see page 24'15).
2. Turn the ignition switch OFF, and wait for ten seconds.
3- Turn the ignition switch ON {ll), and check that the SRS indi
cator light comes on for about six seconds and goes off
Does the SRS indicEtor light stay on?
[*NO
Intermittent lailure, system is OK at this time. See
Troubloshooting Int6rmittent Failures on page 24'15
Ch€ck the No. 13 {15 A} and No. 23 (10 A) fuses:
1. Turn the ignition switch OFF.
2. Check for blown No. 13 (15 A) and No.23 (10 A)fuses in
the under dash fuse/relay box.
Are the fuses OK?
vEs No
Replace the luses, and erase the memory1. Replace the fuses.2. Connect the SCS service connector to the MES con
nector.3. Erase the DTC memory (see page 24 15).
4. Turn the ignitaon switch OFF, then disconnect the SCS
service connector from the MES connector.5. Turn the ignition switch ON (ll).
Does the sRS indicato, tigt t go or "ne. "ii--JJl
-I YEs NO1
ENDi
Conlirm the DTC, and continue troubl6shootilg.
Check for an open in the SRS main harness {VA linell'1. Tu.n the ignition switch OFF.
2. Disconnect the battery negative cable, then disconnect
the positive cable, and wait for three minutes.
3. Disconnect the driver's (and front passenger's) airbag
connectorls) (see page 24 11).
4. Disconnect the SBS main harness '18P connector from
the sRS unir.5, Reconnect the battery positive cable, then reconnect the
negative cable.6. Connect a voltmeter between the No. 7 tetminal (+) of
the SRS main harness 18P connector and ground.
7. Turn the ignition switch on.
b there battery voltageT
YESNO
(A)
To page 24 30
Open in the SRS main harness IVA line); replace the SRS
main harness.
l.J
SBS MAIN
(cont'd)
No. 't3 {15 Al FUSE
SRS UNIT
HARNESS 18P CONNECTOR
II
24-29

Troubleshooting
The SRS Indicator Light Doesn't Go Off -'98 - 00 Models
CAUTION: Whenever the ignition switch is ON {ll}, orhas b66n turned OFF for less than three minutes, becareful not to bump the SRS unit; the airbags coutdaccidentally deploy and cause damage or iniuries.
No. 23 {10 Al FUSEFUSE/RELAY BOX
SRS MAIN HARNESS 18P CONNECTOR
Try to reproduce the SRS indic.tor light:1. Erase the DTC memory (see page 24-15).2. Turn the ignition switch ON (lt), and check that the SRSindicator light comes on for about six seconds and ooesol1.
Intormittent lailulo, systom is OK atthistime. Soo Troublel. o.mittgnl Failuros on paqe24-15.
Check the No. 23 (10 Alfuse:1. Turn the ignition switch OFF.2. Check for blown No. 23 (10 A) tuse in the under,dashfuse/relay box.
Replace ihe fus€, and 6.ase the momory1. Replace the No. 23 110 A) fuse.2. Erase the DTC memory (see page 24,15).3. Turn the ignition switch ON (ll).
Doos the SRS indicator light go off after 3ix second3?
Check tor an open in the SRS msin harness {VB lincl:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait tor three minutes.2. Disconnect the driver's (and front passenger,s) airbagconnector(s) (see page 24-11).3. Disconnect the SRS main harness 18p connector Iromthe sRs unit.4. Reconnect the battery positive cable, then reconnect thenegative cable.5. Connect a voltmeter between the No. 3 terminal (+) ofthe SRS main harness 18P connector ano qrouno.6. Turn the ignition switch ON {ll).
(A)
To page 24-35
24-34

.J
No DTC -'98 - 00 Models
CAUTION: Whenever the ignition switch is ON (ll), or
has been turned OFF for less than three minuies. be
careful not to bump the SRS unil; the airbags could
accidentally deploy and cause damage or iniuries
(A) To page 24'40
Check for short to ground betweon the under-dash fuse/
relav box end the SRS unil
1. TLrrn the ignition switch OFF
2, Disconnect the battery negative cable, then drsconnect
the positive cable, and wait for three minutes'
3. Disconnect the driver's {and front passenger's airbag)
connector{s) {see Page 24_11)
4. Disconnect the SRS main harness 18P connector irom
5. Check resistance between the No 7 terminal of the SRS
main harness 18P connector and ground
There should be 1 M0 or more
(cont'd)
No. 13 {15 A) FUSE
sRs MAIN HARNESS
Check the tuse:Check Ior blown No 13 {15 A) fuse in the under dash fuse/
Beplace the fuse. Turn the ignition switch ON (lll, and check
that lhe tuse doesn't blow
The oroblem has disappeared. Test'drive thc vehicle and
s6e Troubleahoodng lntermittent Failures on pago 2&15
Faufty SRS uniu replace the SRS unii (see page 21-761'
(8)
To page 24 40O1'
24-39

Troubleshooting
No DTG -'98 - 00 Models (cont'dl
trom page 24 39
SRS MAIN HARNESS2P CONNECTOB
SRS MAIN HARTESS18P CONNECTOR
FUSE/RELAY BOX
c807
c807
Wir€ side ot fsmaleterminals
SRS MAIN HAR ESSlAP CONNECTOR
(Bi
Check for short to ground in iho SRS main ha.no$:1. Disconnect the SRS main harness 2P connector from theunder-dash fuse/relay box.2. Check resistance between the No. 7 terminal of the SFSmain harness 18P connector and ground. There shouldbe 1.0 MO or more.
ls lha r6i3tlnce as sp.cilied?
YESNO
Short to ground in the und..-d.sh tu3a/r.lay box;roplace the undsr-dlrh tu!6/rahy box.
Short to ground in fho SRS main harness; rsplecc the SRSmain htrnors.
Check lor an open in the SRS main harn€ls:1- Turn tho ignition switch OFF.2. Disconnect the baftery negative cable, then disconnectthe positive cable, and wait for three minutes.3. Disconnect the driver's (and front passenger's) airbagconnector(sl (see page 24-11).4. Disconnect the SBS main harness 18P connector tromthe sRs unit.5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Connect a voltmeter between the No. 7 terminal ol theSFS main harness 18P connector and qro!nd.7. Turn the ignition switch ON (ll), and measure
Poor contact rt the SRS main harness 18P conn.ctor:chock th€ connectoi.. ll th. connector is OK, iubstitute a known-good SRSunit, and recheck.. lf tho pioblem is still pres6nt. replace the SRS mlinhaanos3.
(A) From page 24 39
To page 24.41
24-40

)
1J
From page 24-42
Check for an opgn in the cabl6 reel (cont'd):
5. Reconnect the battery positive cable, then roconnect the
negative cable.6. Erasethe DTC memory (see page 24 15i
7. Read the DTC (see page 24-13).
l. DTC 1-l or DTC 1-2 indicrt.d?
Opan or incraGad rcsbtanca in tha crbla raal; rapllca
Chcck lor .n oDcn in th. SBS mtin harne$i
1. Disconn€ct the battery negative cabl€, then disconnect
the positive cable, and wait tor three minutes
2, Disconnect the lront passgnger's airbag connoctor from
the SRS main harness (with front pssseng€r's airbag).
3. Disconnect the SRS main harn€ss 18P connector from
the SRS unit. Do not disconnect the special tool {2 0)
from the SRS main harness 2P connector.
4. Check resistance betlveon terminals No. 1 and No 13 ot
the SRS main harness 18P connector.
There should be approx. 2.0 - 3.0 O.
Poor contact rt tha SRS main harna*t 18P connactor;
chack tho clnnactot,. It th. conn.ctol b OK. tubttitut. a known-good SRS
unit. end rcchock..lf the problem is still prcsent, replace tho SRS main
harnoss.
Ooen or incr6asad r.si3tlnca in tha SRS mlin hatnaar;
lfr
24-43

)
Ftom page 24-44
Check for a shon in the cable reel lcont'dl:5, Reconnect the batterv Dositive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-15).7. Read the DTC lsee page 24'13).
Ch€ck tor a shon in the SRS main harness:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the front passenger's airbag connector fromthe SRS main harness (with front passenger's airbag).3. Disconnect the SRS main harness 18P connector trom
the SRS unit. Do not disconnect the special tool (2 0)
from the SRS main harness 2P connector.4. Check resistance between terminals No. 1 and No. 13 ofthe SRS main harness '18P connector.There should be aDorox. 2.0 - 3.0 0.
SRS unit; replace lhe SRS unit lsee ptge 21-
Short in the SRS m.in ha.ness; roplace the SRS mein hal-
Short in the cable reel; replace the cable reel (see
page 21-721.
SRS UNIT
IJ
o1|
24-45

)
From page 24-46
Chock for a short to power in the cabls roel lcont'dl:5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory lsee page 24-15).7. Read the DTC (see pa1e24-131.
b DTC 1-4 indicat€d?
YESNO
Short to power in tho cable reel; roplac. tho cable reel
lsee Dase 24-721.
Chock for e short to powot in the SRS main hornoas:
1. Disconnect the battery nogative cable, then disconnect
the positive cable, and wait for three minutes.2- Disconnect the front passenger's airbag connector lrom
the SRS main harness (with front passenger's airbag).
3. Remove the special tool (2 0) trom the SRS main harn€ss
2P connector./t. Disconnect the SRS main harness 18P connector from
the sRs unit.5. Reconn6ct the battery positive cable, then reconnect the
negative cable.6. Connect a voltmeter between the No. 1 {+i terminal of
the SRS main harness 18P connector and body ground.
7. Turn the ignilion switch ON lll), and measure voltageThere should be 0.5 V or less.8. Turn the ignition switch OFF.9. Connect a voltmeter between the No. 13 (+) torminal ol
the SRS main harness 18P connector 8nd body ground.
lO.Turn the ignition switch ON (ll), and measure voltage
There should be 0.5 V or less.
Aro voltrges a3 specified?
YESNO
Fauftv SRS unh; roplacc tho SRS unh {soe pago 2+761'
Short to power in the SRS main h.rness; .eplace rhe SRS
main harness.
SRS UNIT
IJ
a0
24-47

)
TJ
From page 24-48
Check for a ahort to ground in th. cabl. r.el (cont'd):
5. Reconnect the battery positive cable, then reconnect thenagativ€ cable.6. Erase the DTC memory (see page 24-15).7. Read the DTC (see page 24-13).
b DTC 1-5 indicli.d?
YESNO
Short to ground in tho crblc rocl; rophce the crble roel
k c orsa 2+721.
Chock for e short to ground in tha SRS main harneas:1. Disconnect the battery negative cable, then disconnoctthe positive cable, and wait lor three minutes.2. Disconnect the tront passenger's airbag 2P connectorfrom the SRS main harnsss {with front passeng€r's
airbag).3 Romove the specialtool (2 0)trom th6 SRS main harness2P connoctor,4. Ch€ck resistance between the No. 1 terminal of the SRSmain harness 18P connector and ground. and betwgenthe No. 13 terminal ofthe SRS main harness'l8P connec-tor and grouncl.
There should bo I Mo or more,
la tha raidrnc! .3 rDccified?
NOYES
Flulv SRS unit rcpl.c. th. SRS unit {r€e prg.2+161,
Shon to ground in th. SRS m.in h.rno$; r.pl.ce tho SRSmain harnaas.
SRS UN]T
Ir,
24-49