HONDA CROSSTOUR 2011 Owner's Manual (in English)

How to use the lever on both sides of
the cargo room.Do not put any heavy items on the
seat-back when it is folded down.
Make sure the seat-back is locked
securely and all rear shoulder belts
are positioned in f ront of the rear
seat-backs.
Make sure all items in the cargo area
are secured. Loose items can f ly
f orward and cause injury if you have
to brake hard. See
on page .
To return the seat-back to the
upright position, raise the seat-back
to make sure it is latched. If the seat-
back is not latched f ully, the seat belt
will not work properly and you will
seetheredindicatorbehindthe
release lever as shown.
Make sure there are no passengers
on the rear seats bef ore f olding the
seat-backs.
Pull the lever on either side of the
cargo area and the back of the rear
seat on that side folds down
automatically. 294
Seats
Carrying Cargo
98
LEVERRED INDICATOR
T o prevent spilling the contents of cups,
remove them bef ore f olding the seat-
back down.
10/08/27 14:27:04 31TP6610_103
2011 Accord Crosstour

The rear seat armrest is in the
center of the rear seat. Pivot it down
to use it.
A beverage holder is located in the
armrest.
To use the console lid as an armrest,
slide it to one of its three positions. Armrests
Seats
Inst rument s and Cont rols
99
Rear
Front
10/08/27 14:27:10 31TP6610_104
2011 Accord Crosstour

Both f ront seats are equipped with
seat heaters. Because of the sensors
f or the side airbag cutof f system,
there is no heater in the passenger’s
seat-back. The ignition switch must
be in the ON (II) position to use the
heaters.Push the right side of the switch, HI,
to rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the lef t side of the switch. This will
keep the seat warm.
In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runscontinuously. It does not cycle with
temperature changes.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting. Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
Follow these precautions whenever
you use the seat heaters:
EX-L models
Seat Heaters
100
Driver’s
Seat
Passenger’s
Seat
HEATERS
10/08/27 14:27:18 31TP6610_105
2011 Accord Crosstour

Store a driver’s seat position only
when the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new seat position in memory
unless the ignition switch is in the
ON (II) position. You can recall a
memorized position with the
ignition switch in any position.
Adjust the seat to a comfortable
position (see page ).
Adjust the outside mirrors f or best
visibility (see page ).
Two seat and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2). Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Press and release the SET button.
You will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current position of the driver’s
seat and outside mirrors are now
stored.
1.
2.
3.
4.
105
93
CONT INUED
EX-L modelsStoring a Driving Position in
Memory
Driving Position Memory System
Inst rument s and Cont rols
101
MEMORY BUTTONS
SET BUTTON
10/08/27 14:27:27 31TP6610_106
2011 Accord Crosstour

To select a memorized position, do
this:Make sure the parking brake is set
and the shif t lever is in Park.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
To cancel the storing procedure
after pressing the SET button, press
the SET button again within 5
seconds.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected.
1.
2. Selecting a Memorized Position
Driving Position Memory System
102
MEMORY BUTTONS
10/08/27 14:27:34 31TP6610_107
2011 Accord Crosstour

If desired, you can use the
adjustment switches to change the
positions of the seat or outside
mirrors af ter they are in their
memorized positions. If you change
the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
To stop the system’s automatic
adjustment, do any of these actions:
Press any button on the control
panel: SET, 1, or 2.
Push any of the adjustment
switches f or the seat.
Shif t out of Park.
Adjust the outside mirrors.
The system will move the seat and
outside mirrors to the memorized
positions. The indicator in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps, and the indicator will
remain on.
Driving Position Memory System
Inst rument s and Cont rols
103
10/08/27 14:27:40 31TP6610_108
2011 Accord Crosstour

The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this f eature.
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.
EX model
EX-L models
Mirrors
104
AUTO BUTTON
INDICATOR SENSOR
TAB
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect its
perf ormance.
10/08/27 14:27:46 31TP6610_109
2011 Accord Crosstour

Turn the ignition switch to the ON
(II) position.
Move the selector switch to L
(driver’s side) or R (passenger’s
side).Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
To turn the feature off, place the
switch in the center position. To tilt the passenger’s mirror,
place the switch in the right
position. To tilt the driver’s mirror, place
the selector switch in the left
position.
Both outside door mirrors have a
reverse tilt f eature. When in reverse,
the selected mirror will tilt down
slightly to improve your view as you
parallel park. Shif ting out of reverse
will return the mirror to its original
position.
Outside mirror positions can be
stored in the driving position
memory system (see page ).
1. 3.
2. 4.
101
EX-L models
Adjusting the Power Mirrors Reverse Tilt Door Mirror
Mirrors
Inst rument s and Cont rols
105
SELECTOR SWITCH
ADJUSTMENT SWITCH
10/08/27 14:27:56 31TP6610_110
2011 Accord Crosstour

Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open a window, push the
switchdownandholdit.Releasethe
switch when you want the window to
stop. Pull back on the switch and
hold it to close the window.
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off. Pressing this button also
turns the rear window def ogger on
and off. PowerMirrorHeaters
PowerWindows
Mirrors, Power Windows
106
MAIN SWITCH
FRONT
PASSENGER’S
WINDOW SWITCHINDICATOR
Without navigation system is shown. REAR WINDOW DEFOGGER/
HEATED MIRROR BUTTON
DRIVER’S
WINDOW
SWITCHClosing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.
10/08/27 14:28:03 31TP6610_111
2011 Accord Crosstour

µ
µ If either f ront
window senses any obstacle while it
is closing automatically, it will
reverse direction and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it.
The driver’s window auto
reverse f unction is disabled when
you continuously pull up the switch.
When you push the main switch in,
the indicator comes on and the
passengers’ windows cannot be
raised or lowered. Use the main
switchwhenyouhavechildreninthe
vehicle so they do not injure
themselves by operating the
windows unintentionally. To cancel
this feature, push on the switch
again. The switch will pop out and
the indicator will go of f .
The windows and the main switch
feature will operate for up to 10
minutes after you turn off the
ignition switch. Opening either f ront
door cancels this f unction.
To open either f ront
window f ully, push the window
switch f irmly down to the second
detent, then release it. The window
automatically goes down all the way.
To stop the window f rom going all
the way down, pull back on the
window switch briefly.
To close either f ront window f ully,
pull back the window switch f irmly
to the second detent, then release it.
The window automatically goes all
the way up. To stop the window f rom
going all the way up, push down on
the window switch briefly. AUTO REVERSE
AUTO
Power Windows
Inst rument s and Cont rols
107
NOTE:
10/08/27 14:28:09 31TP6610_112
2011 Accord Crosstour