HONDA INSIGHT 2013 2.G Owners Manual

ÛÝ
ÛÝ
ÛÝ
AUTO DOOR LOCK
Here are the five custom settings for
the door setup:
While ‘‘DOOR SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO
( / ) button, the screen changes
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK TIMER AUTO DOOR UNLOCK
DOOR LOCK MODE
Door Setup
Multi-Inf ormation Display
108
: Press the INFO button .
: Press the INFO button .
: Press the SEL/RESET button. See page
109
See page
110 See page
112
See page
115 See
page
114
12/07/13 16:51:05 31TM8630_113
Inst rument s and Cont rolsTOC
as shown in the illustration. Press
the INFO ( / ) button until you see
2013 Insight

µÛÝ
ÛÝ
µ
µ
Auto Door Lock
There are three settings you can
choose f rom:
SHIFT FROM P
The doors lock whenever you move
the shift lever out of Park.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the selecting mode.
WITH VEHICLE SPEED
The doors lock when the vehicle
speed reaches about 10 mph (about
16 km/h).
OFF
The auto door lock mode is
deactivated all the time.
CONT INUED
Multi-Inf ormation Display
109
12/07/13 16:51:14 31TM8630_114
Inst rument s and Cont rolsTOC
2013 Insight

µµ
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
DOOR LOCK’’ and repeat the
procedure again.
There are f ive possible settings you
can choose f rom:
DRIVER DOOR WITH SHIFT TO P
The driver’s door unlocks when
you move the shif t lever to Park with
the brake pedal depressed.
ALL DOORS WITH SHIFT TO P
All the doors unlock when you move
the shift lever to Park with the brake
pedal depressed.
Auto Door Unlock
Multi-Inf ormation Display
110
12/07/13 16:51:19 31TM8630_115
Inst rument s and Cont rolsTOC
2013 Insight

µ
µ
ÛÝ ÛÝ
µ
DRIVER DOOR WITH IGN OFF
The driver’s door unlocks when you
turn the ignition switch to the LOCK
(0) position.
ALL DOORS WITH IGN OFF All
the doors unlock when you turn the
ignition switch to the LOCK (0)
position.
You can choose this item to
customize from ‘‘DOOR SETUP’’
by pressing the INFO ( / )
button repeatedly.Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button.
For example, you choose ‘‘DRIVER
DOOR with SHIFT to P,’’ you will
seetheabovedisplay.
OFF The auto door unlock is
deactivated all the time.
CONT INUED
Multi-Inf ormation Display
111
12/07/13 16:51:27 31TM8630_116
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝ
Press the SEL/RESET button to
enter your selection. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
DOOR UNLOCK’’ and repeat the
procedure again.To select whether the driver’s or all
doors unlock when you unlock the
doors with the remote transmitter or
the key, follow these instructions.
If you choose ‘‘ALL
DOORS With IGN OFF,’’
you will see the above display.
You can choose this item to
customize from ‘‘DOOR SETUP’’
by pressing the INFO ( / )
button repeatedly.
Door Lock Mode
Multi-Inf ormation Display
112
12/07/13 16:51:35 31TM8630_117
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝ
Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
LOCK MODE’’ and repeat the
procedure again.
Multi-Inf ormation Display
113
12/07/13 16:51:40 31TM8630_118
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝ
ÛÝ Press the SEL/RESET button to
enter the selecting mode.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the hatch
arelockedandthesecuritysystem
has set (see
page). You can
customize the exterior lights not to
f lash and the beeper not to sound. 221
Keyless Lock Acknowledgment
Multi-Inf ormation Display
114
12/07/13 16:51:46 31TM8630_119
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝ
Security Relock Timer
You can change this relock time
f rom 30 seconds to 60 or 90 seconds.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ and repeat
the procedure again. You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors and the hatch,
automatically relock, and the
security system sets.
CONT INUED
Multi-Inf ormation Display
115
12/07/13 16:51:53 31TM8630_120
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝIf the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘SECURITY RELOCK TIMER’’ and
repeat the procedure again.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
116
12/07/13 16:51:58 31TM8630_121
Inst rument s and Cont rolsTOC
2013 Insight

ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button. If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display. To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
the default all setting display.
If the setting is not successfully
completed, ‘‘FAILED’’ is shown for
several seconds, and then the
screen goes back to SETUP. Repeat
the same procedure to select
DEFAULT ALL.
DEFAUL T AL L
Multi-Inf ormation Display
117
12/07/13 16:52:05 31TM8630_122
Inst rument s and Cont rolsTOC
2013 Insight