display HONDA PILOT 2012 2.G Workshop Manual

Playing a Disc (U.S. L X model)
Features
219
DISPLAY
TITLE BUTTON /VOL (POWER/VOLUME) KNOB
SKIP BUTTON
SKIP BUTTON
TUNE/ (SOUND) KNOBDISC EJECT BUTTON
CD BUTTON
RPT/RDM (REPEAT/RANDOM) BAR
FOLDER BAR
SCAN BUTTON
Main MenuTable of Contents

Each time you press the TITLE
button, the display shows you the
text, if the disc was recorded with
text data.
When you press and release the
TITLE button while a disc without
text data is playing, you will see ‘‘NO
INFO

µ
The display shows up to about 14
characters of selected text data (the
foldername,filename,etc.).If the
text data has more than 14
characters, you will see the f irst 14
characters and the indicator in
the display. Press and hold the
TITLE button until the next 14
characters are shown. You will also see some text data
under these conditions:
When a new f older, f ile, or track is
selected.
When you insert a disc, and the
system begins to play.
If any letter is not available, it is
replaced with ‘‘ .

µ
µ
´ µ
µ µ
In MP3 or WMA mode In MP3 or WMA mode
Each time you press and release the
RPTsideof thebar,themode
changes f rom f ile repeat to f older
repeat, then to normal play.This f eature plays the
tracks within a disc (the f iles in MP3
or WMA mode) in random order. To
activate random play, press and
release the RDM side of the RPT/
RDM bar. In MP3 or WMA mode,
presstheRDMsideof thebar
repeatedly to select RDM (within a
disc random play). You will see RDM
in the display. Press the RDM side of
the bar for 2 seconds to return to
normal play.
To
select a dif f erent f older, press either
side of the FOLDER bar. Press the
side of the bar to skip to the next
f older, and the side of the bar to
skip to the beginning of the previous
f older.
To continuously replay
a track (f iles in MP3 or WMA mode),
press and release the RPT side of
theRPT/RDMbar.YouwillseeRPT
in the display. Press and hold the
RPTsidefor2secondstoturnitoff. This feature,
when activated, replays all f iles in
the selected f older in the order they
are compressed. To activate folder
repeat, press the RPT side of the
RPT/RDM bar twice. You will see
F-RPT in the display. The system
continuously replays the current
folder. Press the RPT side of the bar
again to turn it off. Pressing the
RDM side of the bar, or selecting a
different folder with the FOLDER
bar also turns of f the repeat f eature.
CONT INUED
RANDOM (Random within adisc)
FOLDER SELECTION
REPEAT (TRACK/FILE
REPEAT) FOL DER-REPEA T
Playing a Disc (U.S. L X model)
Features
223
Main MenuTable of Contents

µ
µ µ
In MP3 or WMA mode
In MP3 or WMA mode
The system plays the f irst f ile in the
f irst f older f or about 10 seconds. If
you do nothing, the system will then
play the f irst f iles in the next f olders
f or 10 seconds. Af ter playing the f irst
file in the last folder, the system
plays normally.
Pressing either of the SKIP buttons
also turns off the scan feature. This
feature, when activated, samples the
f irst f ile in each f older on the disc.
To activate folder scan, press the
SCAN button twice. You will see
F-SCAN in the display.
Pressing either of the SKIP buttons,
selecting a dif f erent f older with the
FOLDER bar, or pressing the SCAN
button, also turns off the folder scan.
Each time you press and release the
SCAN button, the mode changes
from file scan to folder scan, then to
normal play.
This
feature, when activated, plays all
f iles in the selected f older in random
order. To activate f older random,
presstheRDMsideof theRPT/
RDM bar. You will see F-RDM in the
display. The system will then select
and play f iles randomly. This
continues until you deactivate f older
random by pressing and holding the
RDM side of the bar again, or by
selecting a dif f erent f older with the
FOLDER bar.
Each time you press and release the
RDMsideof thebar,themode
changes f rom f older random play to
random play (within a disc random
play), then to normal play. The scan f unction samples all tracks
(f iles in MP3 or WMA) on the disc in
the order they are recorded on the
disc. To activate scan, press and
release the SCAN button. You will
see SCAN in the display. You will get
a10secondsamplingof eachtrack/
f ile on the disc. Press and hold the
SCAN button until you hear a beep
to get out of scan mode and play the
last track/f ile sampled.
F-SCAN (FOLDER SCAN)
FOLDER-RANDOM SCAN (TRACK/FILE SCAN)
Playing a Disc (U.S. L X model)
224
Main MenuTable of Contents

Thechartontherightexplainsthe
error messages you may see in the
display while playing a disc.
If you see an error message in the
display while playing a disc, press
the eject button. After ejecting the
disc, check it for damage or
deformation. If there is no damage,
insert the disc again.
For additional information on
damaged discs, see page .
Theaudiosystemwilltrytoplaythe
disc. If there is still a problem, the
error message will reappear. Press
the eject button, and pull out the disc.
Insert a dif f erent disc. If the new
disc plays, there is a problem with
the f irst disc. If the error message
cycle repeats and you cannot clear it,
take your vehicle to a dealer.Cause
The ejected disc will not be reloaded automatically. Error Message Solution
333
Track/File format not
supported
Mechanical Error
Servo Error Current track will be skipped. The next
supported track or file plays automatically.
Press the eject button and pull out the disc.
Check the disc f or serious damage, signs of
def ormation, excessive scratches, and/or dirt
(see page 333). Insert the disc again. If the code
does not disappear, or the disc cannot be
removed, consult your dealer. Do not try to
f orce the disc out of the player.
Disc Player Error Messages (U.S. L X model)
226 UNSUPPORTED
BAD DISC
PLEASE CHECK OWNER’S
MANUAL PUSH EJECT
BAD DISC
PLEASE CHECK OWNER’S
MANUAL
Main MenuTable of Contents

To select any setting such as the
clock or sound adjustment, press the
SETUP button. To use any audio
system f unction, the ignition switch
must be in the ACCESSORY (I) or
ON (II) position. You can select the
item by turning the selector knob.
To go back to the previous display,
press the RETURN button.
Pressing the SETUP button again
will also cancel the setup display
mode.
The knob turns lef t and right. Use it
to scroll through lists, or to make
selections or adjustments to a list or
menu item on the display. When you
make a selection, push the center of
the selector to go to that selection.
When the audio system is in XM
Radio mode or playing discs, pushing
the selector knob switches the
display between the normal display
andtheextendeddisplay.
Most audio system f unctions can be
controlled by standard buttons, bars,
and knobs. In addition, you can
access some f unctions by using the
selector knob on the audio system.
Selector K nob
SET UP Display
Audio System (EX, EX-L, and Canadian LX models without navigation s ystem)
Features
227
Without rear entertainment system
SETUP
BUTTON
SELECTOR KNOB SETUP
BUTTON
RETURN BUTTON
With rear entertainment system
RETURN BUTTON
SELECTOR KNOB
Main MenuTable of Contents

µ
µ
You can use any of f ive methods to
f ind radio stations on the selected
band: tune, seek, scan, the preset
buttons, and auto select.
On the AM band, AM noise
reduction turns on automatically.
The band and f requency that the
radio was last tuned to are displayed.
To change bands, press the AM or
FM button, or AM/FM button. On
the FM band, ST will be displayed if
the station is broadcasting in stereo.
Stereo reproduction in AM is not
available.
On the FM band, you can also use
the f eatures provided by the radio
data system (RDS). For more
inf ormation on the RDS, see page
. The skip f unction searches
up and down f rom the current
f requency to f ind a station with a
strong signal. To activate it, press
and hold the or side of the
SKIP bar until you hear a beep, then
release it.
Use the selector knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob. Adjust the
volume by turning the same knob.
232
To Select a Station
To Play the Radio SK IP
TUNE
Playing the FM/AM Radio (EX, EX-L , and Canadian L X models without navigation system)
230
Main MenuTable of Contents

µ
µ µ
Each preset button can
store one f requency on AM and two
f requencies on FM.
Select the desired band, AM or
FM. You can store one f requency
on FM1, and one f requency on
FM2witheachpresetbutton.
Usethetune,skip,scan,orRDS
function to tune the radio to a
desired station.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
When the system finds a strong
signal, it will stop and play that
station f or about 10 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 10 seconds. When it plays
a station that you want to listen to,
press the SCAN button again. If you are
traveling and can no longer receive
your preset stations, you can use the
auto select feature to find stations in
the local area.
Pick a preset button, then press
and hold it until you hear a beep. Push the SETUP button to display
the setup MENU. Turn the selector
knob to select Auto Select, then
press the selector knob. The display
changes to the auto select mode.
Select ‘‘ON,

On the FM band, you can select a
favorite station and display the
program service name provided by
the radio data system (RDS).
You will see ‘‘0