clock HUMMER H2 2008 Owner's Manual

Daytime Running Lamps (DRL)
To replace a daytime running lamp bulb:
1. Locate the lamp
assembly behind the
front bumper through
the wheel opening.
2. Turn the bulb socket counterclockwise and remove
it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install the new bulb into the bulb socket.
5. Reinstall the bulb socket into the lamp housing and
turn it clockwise until it locks.
Roof Marker Lamps
Corner Roof Marker Lamps
To replace one of these bulbs:
1. Remove the screw and lift off the lens.
2. Turn the bulb socket counterclockwise to remove it.
3. Remove the bulb.
4. Install a new bulb into the socket.
5. Reinstall the socket into the lens and turn it
clockwise to lock it into place.
6. Hook the side of the lens with the hook end into the
notch rst and then tighten the screw.
5-50

Center Roof Marker Lamps
To replace one of these bulbs:
1. Push in on the notch with a at tool and pull the
lamp out.
2. Turn the bulb socket counterclockwise and remove
it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install a new bulb into the bulb socket.
5. Place the hook end of the lamp in place on one
side and push the other end of the lamp down
until it locks in place.
Taillamps, Turn Signal, Stoplamps
and Back-up Lamps
A. Stoplamp/Taillamp
B. Turn Signal Lamp
C. Back-Up Lamp
5-51

To replace one of these bulbs:
1. Open the liftgate or tailgate. SeeLiftgate (SUV)
on page 2-13orTailgate/Spare Tire Carrier on
page 2-16for more information.
2. If your vehicle has the taillamp guard, remove it by
removing the four retaining screws. Do not remove
the plastic retainers.
3. Remove the two
screws from the rear
lamp assembly
and remove the rear
lamp assembly.4. Turn the bulb socket counterclockwise to remove it
from the taillamp housing.
5. Pull the bulb straight out from the socket.
6. Press a new bulb into the socket, insert it into the
taillamp housing and turn the socket
counterclockwise until it is locked in place.
7. Reinstall the rear lamp assembly and tighten the
screws.
8. Reinstall the taillamp guard by lining up the guard
with the holes in vehicle. Then install and tighten
the four screws.
5-52

Your vehicle may have a taillamp in the bumper.
To replace it:
1. Locate the affected
taillamp which is
behind and under the
bumper.
2. Turn the bulb socket counterclockwise and remove
it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install the new bulb into the bulb socket.
5. Reinstall the bulb socket into the lamp housing and
turn it clockwise to lock it.Replacement Bulbs
Exterior Lamp Bulb Number
Back-up Lamp 3156K
Daytime Running Lamp (DRL) 4114K LCP
Front Turn Signal and
Parking Lamp4157K or 3157KX
Low-Beam and High-Beam
Headlamps9007
Taillamp and Stoplamp 3057K
Rear Taillamp in Bumper 3057K
Rear Turn Signal Lamp 3156K
Roof Marker Lamp Center 168
Roof Marker Lamp Corner 194
For replacement bulbs not listed here, contact your
dealer/retailer.
5-53

Release the jack by inserting the wheel wrench (A) into
the hole (B) and turn counterclockwise.Before proceeding, be sure to set the wheel blocks at
the appropriate tire as previously shown.
Remove the wheel blocks
from the tool bag. Then lift
the wheel block as
shown to lock it into place.
5-82

Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier. To remove
the spare tire:
In order to remove the spare tire, you may need
someone to assist you.
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.3. Pull off the license plate holder from the spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5. Turn the wheel wrench with the wheel wrench
extender counterclockwise to loosen the wheel nuts.
5-83

Removing the Jack (SUV)
The jack is stored in the rear cargo area on the
driver side.
1. To access the jack pull on the two latches to
remove the trim cover.2. Insert the wheel wrench into the hole and turn it
counterclockwise to release it.
3. Grasp and lift the jack out of the bracket.
5-86

Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier. To remove
the spare tire:
In order to remove the spare tire, you may need
someone to assist you.
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.3. Pull off the license plate holder from the spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts. Turn the
wheel wrench with the wheel wrench extender
counterclockwise to loosen the wheel nuts.
5-87

4. Turn the wheel wrench counterclockwise to loosen
the wheel nuts. Do not remove them yet.
Now jack the vehicle up.
5. Assemble the jack and tools:Front Flat Tire:Attach the jack handle with the
hook end connected to the hole on the jack. Slide
the wheel wrench onto the jack handle extension.
Rear Flat Tire:Assemble the jack together with the
jack handle and the jack handle extensions.
5-89

6. Turn the wheel wrench clockwise to raise the jack
head to the lifting point.
7.Front Flat Tire:Position the jack under the vehicle
on the front lower control arm behind the at tire.Rear Flat Tire:Place the jack under the curved
rear axle pad. Make sure the jack head is positioned
so that the rear axle pad is resting securely on
the jack head.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack. Front Flat Tire – Jack
Rear Flat Tire – Jack
5-90