lock Hyundai Getz 2002 User Guide

1- 14 FEATURES OF YOUR HYUNDAI
HTB027
B080E01O-AAT Lumbar Support Control
(Driver's Seat Only) (If Installed)
HFC2028
Lock knob
To recline the seatback, lean forward to take your weight off it, then pull upon the recliner control lever at theoutside edge of the seat. Now leanback until the desired seatback angle is achieved. To lock the seatback into position, release the recliner controllever. B080D02A-AAT Adjustable Headrests Headrests are designed to help re- duce the risk of neck injuries.To raise the headrest, pull it up. To lower it, push it down while pressing the lock knob.
WARNING:
To minimize risk of severe injury inthe event of a collision or a sudden stop, both the driver and passen- ger seatbacks should always be inan upright position while the ve-hicle is in motion. The protectionprovided by the seat belts andairbags may be reduced significant- ly when the seatbacks are reclined. There is greater risk that the driverand passenger will slide under theseat belt which may result in seri-ous injury if a crash occurs whenthe seatbacks are reclined. The seat belt cannot provide full protection to an occupant if the seat back isreclined.
!
o Do not operate the vehicle with the headrests removed as severe injury to an occupant may occurin the event of an accident. Head-rests may provide protectionagainst severe neck injuries whenproperly adjusted.
!WARNING:
o For maximum effectiveness in case of an accident, the headrest should be adjusted so the top of the headrest is at the same heightas the top of the occupant's ears.The use of a cushion that holdsthe body away from the seatbackis not recommended.
To adjust the lumbar support, turn the handle on the outboard or left side ofthe seat. To increase the amount oflumbar support, pull the lever forward.To decrease it, push the lever toward the rear.

1- 16 FEATURES OF YOUR HYUNDAI
Lock Knob
B090A01FC-GAT Adjustable Headrests
(If Installed) Headrests are designed to help re- duce the risk of neck injuries.To raise the headrest, pull it up. To lower it, push it down while pressing the lock knob.
To recline the seatback, push theseatback folding lever toward the head-rest, and release it after the desiredseatback angle is achieved.When you recline the seatback to de- sired position, always be sure it has locked into position.
CAUTION:
When reclining the seatback angle,you should be adjust the seatbackfolding lever with standing.
!
HFC2028WARNING:
o For maximum effectiveness in case of an accident, the headrest should be adjusted so the top ofthe headrest is at the same height as the top of the occupant's ears.
The use of a cushion that holdsthe body away from the seatbackis not recommended.
o Do not operate vehicle with the headrests removed as severe in- jury to an occupant may occur in the event of an accident. Head-rests may provide protectionagainst severe neck injuries whenproperly adjusted.
!

1- 18 FEATURES OF YOUR HYUNDAI
WARNING:
o When you return the folded down seatback to its upright position, make sure the seat belts are inposition to be accessible and to function properly.
o When you return the folded down seatback to its upright position, be careful not to get your fingersor legs in.
o The purpose of the fold down rear seatback and the fold for-ward rear seat cushion is to in-crease cargo space. Do not allowpassengers to sit in the cargoarea while the car is moving. Thisis not a proper seating position and no seat belts are available for use when the seatback isfolded down. Passengers whoare not properly seated and wear-ing seat belts could sustain seri-ous injuries or death in case of an accident or a sudden stop.
3. A Type: Pull the seat cushion re-
lease handle rear ward, then lift up the entire seat cushion.B Type: Pull the seat cushion re-lease handle rear ward, then lift upa desired seat cushion.
A Type B Type 4. To secure the seat, hook the secur-
ing strap under the seat back to the headrest stay of front driver andpassenger seat.
5. To return the seatback and seat cushion to its normal position, re-verse the above procedure.
o When you return the seatback to its
upright position, always be sure it islocked into position by pulling andpushing on the top of seatback.
HTB030
Seat cushion release handle
HTB030A
Seat cushion release handle
HTB031Securing strap
!
Securing Strap Securing Strap

1- 22 FEATURES OF YOUR HYUNDAI
B180A02A-GAT SEAT BELTS 3-Point System with Emergency Locking Retrac-
tor (If Installed)To Fasten Your Belt
B180A01L
To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an au-dible "click" when the tab locks into thebuckle.The seat belt automatically adjusts tothe proper length only after the lap belt is adjusted manually so that it fits snugly around your hips. If you leanforward in a slow, easy motion, the beltwill extend and let you move around. Ifthere is a sudden stop or impact, how-ever, the belt will lock into position. It
B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT (If Installed)
B170A01L
You can adjust the height of the shoul- der belt anchor to one of the 4 posi-tions.If the height of the adjusting seat belt istoo near your neck, you will not begetting the most effective protection. The shoulder portion should be adjusted so that it lies across yourchest and midway over your shouldernearest the door and not your neck.To adjust the height of the seat beltanchor, lower or raise the height ad- juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressingthe height adjuster button.Release the button to lock the anchorinto position. Try sliding the releasebutton to make sure that it has locked into the position.
WARNING:
o The height adjuster must be in the locked position when the vehicle is moving.
o The misadjustment of height of the shoulder belt could reducethe effectiveness of the seat beltin a crash.
!

FEATURES OF YOUR HYUNDAI 1- 23
B200A01S-GAT Adjusting Your Seat Belt B210A01A-AAT To Release the Seat Belt The seat belt is released by pressing the release button in the locking buckle.When it is released, the belt shouldautomatically draw back into the re- tractor. If this does not happen, check the beltto be sure it is not twisted, then tryagain.
will also lock if you try to lean forwardtoo quickly. Check to make sure thatthe belt is properly locked and that thebelt is not twisted.
B200A01L
You should place the belt as low as possible on your hips, not on yourwaist. If the belt is located too high onyour body, you could slide under it incase of accident or a sudden stop. This could result of death, serious injury or property damage. Both armsshould not be under or over thebelt. Rather, one should be over andthe other under, as shown in the illus-tration. Never wear the seat belt under the armnearest the door.
B210A01L
B220A01A-AAT SEAT BELTS (2-Point Static Type) (Rear Seat Center) (If Installed)To Fasten Your Seat Belt
To fasten a 2-point static type belt, insert the metal tab into the lockingbuckle. There will be an audible "click"when the tab locks into the buckle.Check to make sure the belt is properly locked and that the belt is not twisted. HTB225

1- 24 FEATURES OF YOUR HYUNDAI
B220A01Y-GAT SEAT BELTS - Rear Seat Center's 3-Point System With Emergency Locking Retractor(If installed)
1. Before fastening the rear seat cen-
ter belt, confirm the metal tab (a) and buckle (b) are latched together.
2. After confirming that (a) and (b) are
latched, pull the seat belt out of theretractor and insert the metal tab (c)into the buckle (d).
There will be an audible "click" whenthe tab locks in the buckle. The seat belt automatically adjusts to the proper length only after the lap belt is adjustedmanually so that it fits snugly around HTB192
HTB226
Correct
Shorten Too high
B220B01A-AAT Adjusting Your Seat Belt With a 2-point static type seat belt, the length must be adjusted manually so itfits snugly around your body. Fasten the belt and pull on the loose end to tighten. The belt should be placed aslow as possible on your hips, not onyour waist. If the belt is too high, itcould increase the possibility of yourbeing injured in an accident. B220C01A-AAT To Release the Seat Belt When you want to release the seat belt, press the button in the lockingbuckle.
HTB190
WARNING:
The center lap belt latching mecha-nism is different from those for therear seat shoulder belts. When fas- tening the rear seat shoulder belts or the center lap belt, make surethey are inserted into the correctbuckles to obtain maximum protec-tion from the seat belt system andassure proper operation.
!
(a)
(b) (c)
(d)

FEATURES OF YOUR HYUNDAI 1- 25
your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, the belt will lockinto position. It will also lock if you try tolean forward too quickly. WARNING:
o When using the rear seat center belt, you must lock all metal tabsand buckles. If any metal tab orbuckle is not locked, it will in-crease the chance of injury in theevent of collision.
o Never unlock the metal tab (a)
and the buckle (b) with the fol-lowing exceptions.(1)In case of folding rear
seatbacks down.
(2)If transporting an object on the rear seat may cause dam-age to the rear seat centerbelt.
o Lock the metal tab (a) and the
buckle (b) immediately after fold-ing rear seatbacks up.
!
B220A02Y-D
B220C01Y-GAT To Release the Seat Belt (If installed) When you want to release the seat belt, press the button in the lockingbuckle. HTB191
WARNING:
The center belt latching mechanismis different from those for the rearseat shoulder belts. When fasten- ing the rear seat shoulder belts or the rear seat center belt, make surethey are inserted into the correctbuckles to obtain maximum protec-tion from the seat belt system andassure proper operation.
!

FEATURES OF YOUR HYUNDAI 1- 27
o Never allow a child to stand up or
kneel on the seat.
o Never use an infant carrier or child safety seat that "hooks" over a seatback; it may not provide ad-equate security in an accident.
o Never allow a child to be held in a person's arms while they are in a moving vehicle, as this could re- sult in serious injury to the childin the event of an accident or asudden stop. Holding a child in amoving vehicle does not providethe child with any means of pro- tection during an accident, even if the person holding the child iswearing a seat belt.
o If the child restaint seat is not anchored properly, the risk of a child being seriously injured or killed in a collision greatly in-creases.
B230G01L
WARNING:
Do not install any child restraint sys- tem in the front passenger seat. Should an accident occur and cause the passenger side airbag to deploy,it could severely injure or kill aninfant or child seated in an infant orchild seat. Therefore, only use a childrestraint system in the rear seat of your vehicle.
If you need to tighten the belt, pull more webbing toward the retractor. When youunbuckle the seat belt and allow it toretract, the retractor will automaticallyrevert back to its normal seated pas- senger emergency locking usage con- dition. NOTE:
o Before installing the child re-
straint system, read the instruc- tions supplied by the child re-straint system manufacturer.
o If the seat belt does not operate
as described, have the systemchecked immediately by yourauthorized Hyundai dealer.
!
To install a child restraint system in the outboard rear seats, extend the shoul-der/lap belt from its retractor. Install the child restraint system, buckle the seat belt and allow the seat belt to takeup any slack. Make sure that the lapportion of the belt is tight around thechild restraint system and the shoulderportion of the belt is positioned so that it cannot interfere with the child's head or neck. After installation of the childrestraint system, try to move it in alldirections to be sure the child restraintsystem is securely installed.B230G01A-GAT Installation on Outboard Rear Seats

FEATURES OF YOUR HYUNDAI 1- 31
B230H01TB-GAT Child Seat Restraint Suitability For Seat Position Use child safety seats that have been officially approved and are appropriate for your children. When using the childsafety seats, refer to the following table.
Rear
Center
Age Group Seating Position
UX
X UX
Rear
Outboard
Front
Passenger
0 : Up to 10 kg (0 ~ 9 months)0+ : Up to 13 kg(0 ~ 2 years)I : 9kg to 18kg(9 months ~ 4years)II & III : 15kg to36kg (4 ~ 12 years) X
o Always follow the installation and
use instructions provided by the manufacturer of the child restraint.
X U, L1 X XUFXB180C01A-GAT Pre-tensioner Seat Belt (Without A/BAG) (If Installed) Ordinarily the pre-tensioner seat belt operates in the same way as E.L.R(Emergency Locking Retractor) type(When vehicles stop suddenly, the beltwill lock into the position. It will also lock if you try to lean forward too quickly.). However, when vehiclescrash, the retractor rewinds the beltwebbing. This will restrain the passen-ger movement quickly and also reducethe slack between passenger and belt webbing. NOTE:
o When the pre-tensioner seat belt
is activated, there may be an ex- plosion noise. This noise is nor-mal and is not hazardous.
o Pre-tensioner seat belt is de- signed to operate only when a sufficiently severe impact occurs and it will be only operated once.
U : Suitable for "universal" category
restraints approved for use in thismass group
UF: Suitable for forward-facing "univer- sal" category restraints approved for use in this mass group
L1 : Suitable for "Römer ISOFIX GR1" approved for use in this mass group (Approval No: E1 R44-03301133)
X : Seat position not suitable for chil- dren in this mass group

1- 32 FEATURES OF YOUR HYUNDAI
B180B01A-GAT Pre-tensioner Seat Belt (With A/BAG) (If Installed) Your Hyundai vehicle is equipped with driver's and front passenger's pre-tensioner seat belts. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against theoccupant's body in certain frontal col-lisions.The pre-tensioner seat belts can beactivated with the airbags. The pre-tensioner seat belt operates inthe same way as an Emergency Lock- ing Retractor (ELR) type of seat belt. When the vehicle stops suddenly, or ifthe occupant tries to lean forward tooquickly, the seat belt retractor will lockinto position. However, in certain frontalcollisions, the pre-tensioner will acti- vate and pull the seat belt into tighter contact against the occupant's body.
WARNING:
If the pre-tensioner seat belt wasactivated, never attempt to replaceit by yourself. It must be replacedby an authorized Hyundai Dealer.
!
HXG229
The seat belt pre-tensioner system consists mainly of the following compo-nents. Their locations are shown in the illus- tration.
1. SRS airbag warning light
2. Seat belt pre-tensioner assembly
3. SRS control module HTB198
Driver's airbag1
2 3Passenger's airbag