engine stop HYUNDAI I10 2023 Owner's Manual
Page 289 of 486
6-33
0606
Power brakes
Your vehicle has power-assisted
E U D N H V W K D W D G M X V W D X W R P D W L F D O O \
through normal usage.
If the engine is not running or is
turned off whilst driving, the power
assist for the brakes will not work.
You can still stop your vehicle by
applying greater force to the brake
pedal than typical. The stopping dis-
tance, however, will be longer than
with power brakes.
When the engine is not running, the
reserve brake power is partially
depleted each time the brake pedal is
applied. Do not pump the brake pedal
when the power assist has been
interrupted.
3 X P S W K H E U D N H S H G D O R Q O \ Z K H Q
necessary to maintain steering con-
trol on slippery surfaces.
WARNING
Take the following precautions:
Page 292 of 486
6-36
Whilst driving
Using ABS
To obtain the maximum benefit from
\ R X U $ % 6 L Q D Q H P H U J H Q F \ V L W X D W L R Q
do not attempt to modulate your
brake pressure and do not try to
pump your brakes. Depress your
brake pedal as hard as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the
brakes, or feel a corresponding sen-
sation in the brake pedal. This is nor-
P D O D Q G L W P H D Q V \ R X U $ % 6 L V D F W L Y H
$ % 6 G R H V Q R W U H G X F H W K H W L P H R U G L V-
tance it takes to stop the vehicle.
Always maintain a safe distance from
the vehicle in front of you.
$ % 6 Z L O O Q R W S U H Y H Q W D V N L G W K D W U H V X O W V
from sudden changes in direction,
such as trying to take a corner too
fast or making a sudden lane change.
Always drive at a safe speed for the
road and weather conditions.
$ % 6 F D Q Q R W S U H Y H Q W D O R V V R I V W D E L O L-
ty. Always steer moderately when
braking hard. Severe or sharp steer-
ing wheel movement can still cause
your vehicle to veer into oncoming
traffic or off the road.
On loose or uneven road surfaces,
operation of the anti-lock brake sys-
tem may result in a longer stopping
distance than for vehicles equipped
with a conventional brake system.
7 K H $ % 6 Z D U Q L Q J O L J K W
) will stay
on for several seconds after the igni-
tion switch is in the ON position.
' X U L Q J W K D W W L P H W K H $ % 6 Z L O O J R
through self-diagnosis and the light
will go off if everything is normal. If
the light stays on, you may have a
S U R E O H P Z L W K \ R X U $ % 6 : H U H F R P-
mend that you contact a HYUNDAI
authorised repairer as soon as pos-
sible.
WARNING
If the ABS warning light () is on
and stays on, you may have a
problem with the ABS. Your power
brakes will work normally. To
reduce the risk of serious injury or
death, we recommend that you
contact a HYUNDAI authorised
repairer as soon as possible.
NOTICE
When you drive on a road having
poor traction, such as an icy road,
and apply your brakes continuous-
ly, the ABS will be active continu-
ously and the ABS warning light
(
) may illuminate. Pull your
vehicle over to a safe place and
turn the engine off.
Restart the engine. If the ABS
warning light is off, then your ABS
system is normal.
Otherwise, you may have a prob-
lem with your ABS system. We rec-
ommend that you contact a
HYUNDAI authorised repairer as
soon as possible.
i Information
When you jump start your vehicle
because of a drained battery, the ABS
warning light (
) may turn on at the
same time. 7his happens because of the
low battery voltage. It does not mean
your ABS is malfunctioning. +ave the
battery recharged before driving the
vehicle.
Page 300 of 486
6-44
Whilst driving
The ISG system is to reduce the fuel
consumption by automatically shut-
ting down the engine, when the vehi-
cle is at a standstill (i.e. red stop light,
V W R S V L J Q D Q G W U D I I L F M D P
The engine is automatically started
upon satisfying the starting condi-
tions.
The ISG system is always active,
when the engine is running.
i Information
When the engine is automatically
started by the IS * system, some warn-
ing lights (i.e. ABS, ESC, ESC 2FF,
EPS, and parking brake warning light)
may illuminate for a few seconds due
to the low battery voltage. +owever, it
does not indicate a malfunction with
the IS * system.
To activate the ISG system
Prerequisite for activation
The ISG system operates in the fol-
lowing situations.
‡ 7 K H G U L Y H U‹ V V H D W E H O W L V I D V W H Q H G
Page 301 of 486
6-45
06
Auto stop
7o stop the engine in idle stop mode
Manual transmission vehicle
' H F U H D V H W K H Y H K L F O H V S H H G W R
P S K N P K
2. Set the gear in N (Neutral).
3. Release the clutch pedal.
The auto stop indicator (
) illumi-
nates in green on the instrument clus-
ter, when the engine stops.
i Information
7he driving speed must reach at least 5
km/h (3 mph) after an idle stop to stop
the engine in idle stop mode again.
Automated Manual Transmission
vehicle
' H F U H D V H W K H Y H K L F O H V S H H G W R
km/h.
2. Depress the brake pedal with the
shift lever in D (Drive) or N (Neutral).
The auto stop indicator () illumi-
nates in green on the instrument clus-
ter, when the engine stops.
i Information
7he driving speed must reach at least 3
mph (5 km/h) after an idle stop to stop
the engine in idle stop mode again.In auto stop mode, when the driver
opens the bonnet, the ISG system
will be deactivated.
: K H Q W K H V \ V W H P L V G H D F W L Y D W H G
2 $ & 7 8
The ISG OFF button indicator illumi-
nates.
2 $ & 7 8
The message, ‘‘Auto Stop is Off.
3 U H V V F O X W F K S H G D O D Q G V W D U W H Q J L Q H
manually’’, appears on the LCD dis-
play with a beep sound.
Page 302 of 486
6-46
Whilst driving
At this time, restart the vehicle manu-
D O O \ E \
Manual transmission vehicle
Depressing the clutch and brake
pedal with the gear in neutral.
Automated Manual Transmission
vehicle
Depressing the brake pedal with the
shift lever in N (Neutral).
Auto start
7o restart the engine in the auto stop
mode
Manual transmission vehicle
Page 346 of 486
6-90
Whilst driving
Hydroplaning
If the road is wet enough and you are
going fast enough, your vehicle may
have little or no contact with the road
surface and actually ride on the water.
The best advice is SLOW DOWN
when the road is wet.
The risk of hydroplaning increases
as the depth of tyre tread decreas-
es, refer to “Tyre replacement” in
chapter 8.
Driving in flooded areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel
hub. Drive through any water slowly.
Allow adequate stopping distance
because brake performance may be
reduced.
After driving through water, dry the
brakes by gently applying them sev-
eral times whilst the vehicle is moving
slowly.
Highway driving
Tyres
$ G M X V W W K H W \ U H L Q I O D W L R Q D V V S H F L I L H G
Under-inflation may overheat or dam-
age the tyres.
Do not install worn-out or damaged
tyres, which may reduce traction or
fail the braking operation.
i Information
1ever over-inflate your tyres above the
maximum inflation pressure, as speci-
fied on your tyres.
Fuel, engine coolant and engine
oil
Driving at higher speeds on the high-
way consumes more fuel and is less
efficient than driving at a slower, more
P R G H U D W H V S H H G 0 D L Q W D L Q D P R G H U-
ate speed in order to conserve fuel
when driving on the highway.
% H V X U H W R F K H F N E R W K W K H H Q J L Q H
coolant level and the engine oil before
driving.
Drive belt
A loose or damaged drive belt may
overheat the engine.
Page 349 of 486
6-93
06
Chain Installation
When installing tyre chains, follow the
manufacturer’s instructions and
mount them as tightly possible. Drive
V O R Z O \ O H V V W K D Q P S K N P K
with chains installed. If you hear the
chains contacting the body or chas-
sis, stop and tighten them. If they still
make contact, slow down until the
noise stops. Remove the tyre chains
as soon as you begin driving on
cleared roads.
When mounting snow chains, park
the vehicle on level ground away from
traffic. Turn on the vehicle Hazard
Warning Flasher and place a triangu-
lar emergency warning device behind
the vehicle (if available). Always
S O D F H W K H Y H K L F O H L Q 3 3 D U N D S S O \
the parking brake and turn off the
engine before installing snow chains.
NOTICE
When using tyre chains:
Page 355 of 486
7-3
07
OAC3079001TU
The hazard warning flasher serves as
a warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
To turn the hazard warning flasher on
or off, press the hazard warning flash-
er button with the ignition switch in
any position. The button is located in
the centre fascia panel. All turn signal
lights will flash simultaneously.
‡ The hazard warning flasher oper-
ates whether your vehicle is run-
ning or not.
‡ The turn signals do not work when
the hazard flasher is on
HAZARD WARNING FLASHER IN CASE OF AN EMERGENCY
WHILST DRIVING
, I W K H H Q J L Q H V W D O O V Z K L O V W
G U L Y L Q J
‡ Reduce your speed gradually,
keeping a straight line. Move cau-
tiously off the road to a safe place.
‡ Turn on your hazard warning flash-
er.
‡ Try to start the engine again. If your
vehicle will not start, we recom-
mend that you contact a HYUNDAI
authorised repairer.
, I W K H H Q J L Q H V W D O O V D W D F U R V V-
U R D G R U F U R V V L Q J
If the engine stalls at a crossroads or
crossing, if safe to do so, move the
shift lever to the N (Neutral) position
and then push the vehicle to a safe
location.
Page 361 of 486
7-9
07
If your temperature gauge indicates
overheating, you experience a loss of
power, or hear loud pinging or knock-
ing, the engine may be overheating. If
this happens, you should:
1. Pull off the road and stop as soon
as it is safe to do so.
2. Place the shift lever in N (Neutral,
for Automated manual transmis-
sion vehicle) or neutral (for Manual
transmission vehicle) and set the
parking brake. If the air condition-
ing is ON, turn it OFF.
3. If engine coolant is running out
under the vehicle or steam is com-
ing out from the bonnet, stop the
engine. Do not open the bonnet
until the coolant has stopped run-
ning or the steaming has stopped.
If there is no visible loss of engine
coolant and no steam, leave the
engine running and check to be
sure the engine cooling fan is oper-
ating. If the fan is not running, turn
the engine off.
WARNING
: K L O V W W K H H Q J L Q H L V U X Q-
Q L Q J N H H S K D Q G V F O R W K-
L Q J D Q G W R R O V D Z D \ I U R P
W K H P R Y L Q J S D U W V V X F K
D V W K H F R R O L Q J I D Q D Q G
G U L Y H E H O W W R S U H Y H Q W
V H U L R X V L Q M X U \ 4. Check for coolant leaking from the
radiator, hoses or under the vehi-
cle. (If the air conditioning had
been in use, it is normal for cold
water to be draining from it when
you stop.)
5. If engine coolant is leaking out,
stop the engine immediately and
we recommend that you call a
HYUNDAI authorised repairer for
assistance.
WARNING
1 ( 9 ( 5 U H P R Y H W K H U D G L-
D W R U F D S R U W K H G U D L Q
S O X J Z K L O V W W K H H Q J L Q H
D Q G U D G L D W R U D U H K R W + R W
F R R O D Q W D Q G V W H D P P D \
E O R Z R X W X Q G H U S U H V V X U H F D X V L Q J
V H U L R X V L Q M X U \
7 X U Q W K H H Q J L Q H R I I D Q G Z D L W X Q W L O
W K H H Q J L Q H F R R O V G R Z Q 8 V H
H [ W U H P H F D U H Z K H Q U H P R Y L Q J W K H
U D G L D W R U F D S : U D S D W K L F N W R Z H O
D U R X Q G L W D Q G W X U Q L W F R X Q W H U F O R F N-
Z L V H V O R Z O \ W R W K H I L U V W V W R S 6 W H S
E D F N Z K L O V W W K H S U H V V X U H L V
U H O H D V H G I U R P W K H F R R O L Q J V \ V W H P
: K H Q \ R X D U H V X U H D O O W K H S U H V V X U H
K D V E H H Q U H O H D V H G S U H V V G R Z Q R Q
W K H F D S X V L Q J D W K L F N W R Z H O D Q G
F R Q W L Q X H W X U Q L Q J F R X Q W H U F O R F N Z L V H
W R U H P R Y H L W
IF THE ENGINE OVERHEATS
Page 375 of 486
7-23
07
- D F N O D E H O
The actual Jack label in the vehicle
may differ from the illustration.
For more detailed specifications,
refer to the label attached to the jack.
1. Model Name
2. Maximum allowable load
3. When using the jack, set your park-
ing brake.
4. When using the jack, stop the
engine.
5. Do not get under a vehicle that is
supported by a jack.
6. The designated locations under
the frame7. When supporting the vehicle, the
base plate of jack must be vertical
under the lifting point.
8. Shift into R (Reverse) gear on vehi-
cles with Manual transmission or
move the shift lever to the N
(Neutral) position on vehicles with
Automated manual transmission.
9. The jack should be used on firm
level ground.
10. Jack manufacture
11. Production date
12. Representative company and
address
OHYK065011