clock HYUNDAI I20 2014 User Guide

! $#'#"'"' %'$%'&&&%
JJack and tools ➀Jack
➁ Jack handle
➂ Wheel lug nut wrench
➃ Towing hook
The jack, jack handle, and wheel lug
nut wrench, towing hook are stored
in the luggage compartment under
the luggage box cover.
The jack is provided for emergency
tire changing only.
Removing and storing the spare
tireTurn the winged hold down bolt
counterclockwise to remove the
spare tire.
Store the spare tire in the same com-
partment by turning the winged hold
down bolt clockwise.
To prevent the spare tire and tools
from “rattling,” store them in their
proper location.
$"%""!!$ %
OIB067021
OIB067020
Changing a tire can be dangerous.
Follow the instructions in this sec-
tion when changing a tire to
redu ce the risk of serious injury or
death.
WARNING

!
$#'#"'"' %'$%'&&&%
If it is hard to loosen the tire hold-
down wing bolt by hand, you can
loosen it easily using the wheel lug
nut wrench.
1. Put the wrench (1) inside of the tire hold-down wing bolt.
2. Turn the tire hold-down wing bolt counterclockwise with the wrench.
CChanging tires A vehicle can slip or roll off of a
jack causing serious injury or
death to you or those nearby.
Take th e following safety precau-
tions:•
Do not get under a vehicle that
is supported by a jack.
•
NEVER attempt to change a tire
in the lane of traffic. ALWAYS
move the vehicle completely off
the road o n level, firm ground
away from traffic before trying to
change a tire. If you cannot find
a level, firm place off the road,
call a towing service for assis-
tance.
•
Be sure to use the jack provided
with the vehicle.
(Continued)
(Continued)•
ALWAYS place the jack on the
designated jacking positions on
the vehicle and NEVER on the
bumpers or any other part of the
vehicle for jacking support.
•
Do not start or run the engine
while the vehicle is on the jack.
•
Do not allow anyone to remain
in the vehicle while it is on the
jack.
•
Keep children away from the
road and the vehicle.
WARNING
OIB067022

!$#'#"'"' %'$%'&&&%
Follow these steps to change your
v ehicle’s tire:
1.Park on a level, firm surface.
2.Move the shift lever into P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), apply the park-
ing brake, and place the ignition
switch in the LOCK/OFF position.
3.Press the hazard warning flasher button.
4.Remove the wheel lug nut wrench, jack, jack handle, and spare tire
from the vehicle.
5.Block both the front and rear of the tire diagonally opposite of the tire
you are changing. 6.Loosen the wheel lug nuts counter-
clockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground. 7.Place the jack at the designated
jacking position under the frame
closest to the tire you are chang-
ing. The jacking positions are
plates welded to the frame with two
tabs and a raised dot. Never jack
any other position or part of the
vehicle.
OIB067006
OIB067005

!

$#'#"'"' %'$%'&&&%
8.Insert the jack handle into the jackand turn it clockwise, raising the
vehicle until the tire clears the ground. Make sure the vehicle is
stable on the jack. 9.Loosen the lug nuts with the wheel
lug nut wrench and remove them
with your fingers. Remove the
wheel from the studs and lay it flat
on the ground out of the way.
Remove any dirt or debris from the
studs, mounting surfaces, and
wheel.
10. Install the spare tire onto the studs of the hub.
11. Tighten the lug nuts with your fin- gers onto the studs with the
smaller end of the lug nuts clos-
est to the wheel.
12. Lower the vehicle to the ground by turning the jack handle coun-
terclockwise. 13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
changing tires, we recommend
that an authorized HYUNDAI
dealer tighten the lug nuts to their
proper torque as soon as possi-
ble. T
T
he wheel lug nut should be
tightened to 11~13 kgf.m (79~94
lbf.ft).
OIB067008
OIB067007

!!$#'#"'"' %'$%'&&&%
•• Do not tow the vehicle with 4
wheels on the ground (such as
dinghy towing behind a motorhome
or other m otor vehicle) as this can
seriously damage the
Continuously Variable Transaxle.
• Do not tow the vehicle with the
front wheels on the ground as this
may cause damage to the vehicle.
• Do not tow with sling-type equip-
ment. Use a wheel lift or flatbed
equipment.When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.Failure to place the shift lever in N
(Neutral) when being towed with the
front wheels on the ground can
cause internal damage to the
transaxle.
Removable towing hook 1.Open the trunk, and remove the towing hook from the tool case. 2.Remove the hole cover pressing
the lower part of the cover on the
front bumper.
3.Install the towing hook by turning it clockwise into the hole until it is
fully secured.
4.Remove the towing hook and install the cover after use.
NOTICENOTICE
OIB067013OIB064017
■ 5 Door■Cross

1.#),204/3424-3
IInformation
If the memory fuse is pulled up from
the fuse panel, the warning chime,
audio, clock and interior lamps, etc.,
will not operate. Some items must
be reset after replacement. Refer to
"Battery" in this chapter.
Even though the memory fuse is pulled up, the battery can still be
discharged by operation of the
headlights or other electrical
devices.
Engine compartment panel fuse
replacement1. Turn the ignition switch and all
other switches off.
2. Remove the fuse box cover by pressing the tab and pulling up the
cover.
3. Check the removed fuse; replace it if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips. If it fits loosely, we rec-
ommend that you consult an
authorized HYUNDAI dealer.
After checking the fuse panel in the
engine compartment, securely install
the fuse panel cover. If not, electrical
failures may occur from water leak-
ing in.NOTICE
i
OIB074031

1.#$
,204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
SAFETY P/WDW
25A
Driver Safety Power Window Module
P/WDW LH
25A
Power Window Main Switch, Passenger Power Window Switch (RHD)
HTD MIRR
10A
PCM/ECM, A/C Control Module, Driver/Passenger Power Outside Mirror
FOG LP FRT
10A
Front Fog Lamp Relay
RR HTD
30A
RR HTD Relay
P/WDW RH
25A
Driver Power Window Switch
STOP LAMP
STOP
LAMP
15A
Stop Signal Electronic Module
POWER OUTLET LH
20A
Power Outlet LH & USB Charger
DR LOCK
20A
T/Gate Unlock Relay, Door Lock/Unlock Relay
A/CON 2
10A
A/CON Fuse for Clutch+Condition
POWER OUTLET RH
20A
Power Outlet RH
BLOWER
10A
A/C Control Module, Blower Motor
ACC
10A
Power Outside Mirror Switch, Auido, Digital Clock, BCM, Smart Key Control Module,
I/P Junction Block (P/OUTLET Relay)
START
10A
CVT : Transaxle Range Switch,
M/T : PCM/ECM, E/R Junction Block (Start Relay), Ignition Lock Switch,
Smart Key Control Module, Clutch Switch
TURN
15A
BCM
Driver’s side fuse panel

1.#1
,204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
MDPS
1
10A
MDPS Unit
MODULE1
10A
BCM, Sport Mode Switch, Stop Lamp Switch
MODULE 4
10A
BCM, Smart Key Control Module
A/CON 1
1A/C
10A
PCB Block (Blower Relay), A/C Control Module, Cluster Ionizer ( Auto A/C)
WASHER
15A
Multifunction Switch
MODULE 5
10A
Head Lamp Leveling Device Switch, Head Lamp Leveling Device Actuator LH/RH,
BCM, PCB Block (H/Lamp HI Relay)
A/BAG IND
10A
Instrument Cluster
AUDIO
20A
Audio
ROOM LP
10A
Luggage Lamp, Room Lamp, BCM, Hazard Switch & Door Lock Switch, Map Lamp,
Center Room Lamp, Data Link Connector, Digital Clock, Instrumen t Cluster,
A/C Control Module
Driver’s side fuse panel

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross