HYUNDAI I20 2014 Owners Manual

Page 281 of 400

+)
!-0,0*&."'$-.,/#0%(/

Smooth cornering
Avoid braking or gear changing in
corners\b especially when roads are
wet. Ideally\b corners should always
be taken under gentle acceleration.
Driving at night
Night driving presents more hazards
than driving in the daylight. Here are
some important tips to remember:
• Slow down and keep more distance between you and other vehi
cles\b as it may be more difficult to
see at night\b especially in areas
where there may not be any street
lights.
• Adjust your mirrors to reduce the glare from other driver's head
lights.
• Keep your headlights clean and properly aimed. Dirty or improperly
aimed headlights will make it much
more difficult to see at night.
• Avoid staring directly at the head lights of oncoming vehicles. You
could be temporarily blinded\b and it
will take several seconds for your
eyes to readjust to the darkness.
Driving in the rain
Rain and wet roads can make driving
dangerous. Here are a few things to
consider when driving in the rain or
on slick pavement:
• Slow down and allow extra following distance. A heavy rainfall
makes it harder to see and increas
es the distance needed to stop
your vehicle.
• Replace your windshield wiper blades when they show signs of
streaking or missing areas on the
windshield.
• Be sure your tires have enough tread. If your tires do not have
enough tread\b making a quick stop
on wet pavement can cause a skid
and possibly lead to an accident.
See “Tire Tread ”
in chapter 7.
• Turn on your headlights to make it easier for others to see you.

Page 282 of 400

• Driving too fast through large puddles can affect your brakes. If you
must go through puddles\b try to
drive through them slowly.
• If you believe your brakes may be wet\b apply them lightly while driv
ing until normal braking operation
returns.
Hydroplaning
If the road is wet enough and you are
going fast enough\b your vehicle may
have little or no contact with the road
surface and actually ride on the
water. The best advice is SLOWDOWN when the road is wet. The
risk of hydroplaning increases as the
depth of tire tread decreases\b refer to
“Tire Tread” in chapter 7.
Driving in flooded areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel
hub. Drive through any water slowly.
Allow adequate stopping distance
because brake performance may be
reduced.
After driving through water\b dry the
brakes by gently applying them sev
eral times while the vehicle is moving
slowly.
!-0,0*&."'$-.,/#0%(/
+)

Page 283 of 400

Snow or icy conditions
You need to keep sufficient distance
between your vehicle and the vehicle
in front of you.
Apply the brakes gently. Speeding\b
rapid acceleration\b sudden brake
applications\b and sharp turns are
potentially very hazardous practices.
During deceleration\b use engine
braking to the fullest extent. Sudden
brake applications on snowy or icy
roads may cause skids to occur.
To drive your vehicle in deep snow\b it
may be necessary to use snow tires
or to install tire chains on your tires.
Always carry emergency equipment.
Some of the items you may want to
carry include tire chains\b tow straps
or chains\b a flashlight\b emergency
flares\b sand\b a shovel\b jumper cables\b
a window scraper\b gloves\b ground
cloth\b coveralls\b a blanket\b etc.
Snow tires
If you mount snow tires on your vehi
cle\b make sure to use radial tires of
the same size and load range as the
original tires. Mount snow tires on all
four wheels to balance your vehicle’s
handling in all weather conditions.
The traction provided by snow tires
on dry roads may not be as high as
your vehicle's original equipmenttires. Check with the tire dealer for
maximum speed recommendations.
Information
Do not install studded tires without
first checking local and municipal reg
ulations for possible restrictions
against their use\b
i
W(&$'#
#(V(&
Snow tires should be equivalent in
size and type to the vehicle's stan
dard tires. Otherwise\b the safety
and handling of your vehicle may
be adversely affected.
WARNING

!-0,0*&."'$-.,/#0%(/
+)+

Page 284 of 400

Tire chains
Since the sidewalls of radial tires are
thinner than other types of tires\b they
may be damaged by mounting some
types of tire chains on them.
Therefore\b the use of snow tires is
recommended instead of tire chains.
Do not mount tire chains on vehicles
equipped with aluminum wheels; if
unavoidable use a wire type chain. If
tire chains must be used\b use gen
uine HYUNDAI parts and install the
tire chain after reviewing the instruc
tions provided with the tire chains.
Damage to your vehicle caused by
improper tire chain use is not cov
ered by your vehicle manufacturer’s
warranty.
Information
• Install tire chains on the front tires\bIt should be noted that installing tire
chains on the tires will provide a
greater driving force, but will not
prevent side skids\b
• Do not install tire chains without first checking local and municipal
regulations for possible restrictions
against their use\b
Chain Installation
When installing tire chains\b follow the
manufacturer's instructions and
mount them as tightly possible. Drive
slowly (less than 3\f km/h (2\f mph))
with chains installed. If you hear the
chains contacting the body or chas
sis\b stop and tighten them. If they still
make contact\b slow down until the
noise stops. Remove the tire chains
as soon as you begin driving on
cleared roads.
When mounting snow chains\b park
the vehicle on level ground away
from traffic. Turn on the vehicle
Hazard Warning Flasher and place a
triangular emergency warning device
behind the vehicle (if available).
Always place the shift lever in neu
tral\b apply the parking brake and turn
off the engine before installing snow
chains.
i
OIB\f57\f11
The use of tire chains may
adversely affect vehicle handling:
•Drive less than 3\f km/h (2\f
mph) or the chain manufactur
er’s recommended speed limit\b
whichever is lower.
•Drive carefully and avoid
bumps\b holes\b sharp turns\b and
other road hazards\b which may
cause the vehicle to bounce.
•Avoid sharp turns or locked
wheel braking.
WARNING
!-0,0*&."'$-.,/#0%(/
+)

Page 285 of 400

When using tire chains:
• Wrong size chains or improperlyinstalled chains can damage your
vehicle's brake lines\b suspension\b
body and wheels.
• Use SAE “S” class or wire chains.
• If you hear noise caused by chains contacting the body\b retighten the
chain to prevent contact with the
vehicle body.
• To prevent body damage\b retighten the chains after driving \f.5~1.\f km
(\f.3~\f.6 miles).
• Do not use tire chains on vehic
les
equipped with aluminum wheels. If
unavoidable\b use a wire type
chain.
• Use wire chains less than 15 mm (\f.59 in) wide to prevent damage
to the chain’s connection.
Winter precautions
Use high quality ethylene glycolcoolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because
it helps prevent corrosion in the cool
ing system\b lubricates the water
pump and prevents freezing. Be sure
to replace or replenish your coolant
in accordance with the maintenance
schedule in chapter 7. Before winter\b
have your coolant tested to assure
that its freezing point is sufficient for
the temperatures anticipated during
the winter.
Check battery and cables
Winter puts additional burdens on
the battery system. Visually inspect
the battery and cables as described
in chapter 7. The level of charge in
your battery can be checked by an
authorized HYUNDAI dealer or a
service station.
Change to "winter weight" oil if necessary
In some climates it is recommended
that a lower viscosity "winter weight"
oil be used during cold weather. See
chapter 8 for recommendations. If
you aren't sure what weight oil you
should use\b we recommend that you
consult with an authorized HYUNDAI
dealer.
Check spark plugs and ignition system
Inspect your spark plugs as
described in chapter 7 and replace
them if necessary. Also check all
ignition wiring and components to be
sure they are not cracked\b worn or
damaged in any way.
NOTICE

!-0,0*&."'$-.,/#0%(/
+)

Page 286 of 400

To keep locks from freezing
To keep the locks from freezing\b
squirt an approved deicer fluid or
glycerine into the key opening. If a
lock is covered with ice\b squirt it with
an approved deicing fluid to remove
the ice. If the lock is frozen internally\b
you may be able to thaw it out by
using a heated key. Handle the heat
ed key with care to avoid injury.
Use approved window washerantifreeze in system
To keep the water in the window
washer system from freezing\b add an
approved window washer antifreeze
solution in accordance with instruc
tions on the container. Window wash
er antifreeze is available from an
authorized HYUNDAI dealer and
most auto parts outlets. Do not use
engine coolant or other types of anti
freeze as these may damage the
paint finish.
Don't let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged
position. This is most likely to hap
pen when there is an accumulation
of snow or ice around or near the
rear brakes or if the brakes are wet.
If there is a risk the parking brake
may freeze\b apply it only temporarily
while you put the shift lever in P (for
Automatic Transaxle/Continuously
Variable Transaxle) or in first or
reverse gear (for Manual Transaxle)
and block the rear wheels so the
vehicle cannot roll. Then release the
parking brake.
Don't let ice and snow accumulate underneath
Under some conditions\b snow and
ice can build up under the fenders
and interfere with the steering. When
driving in severe winter conditions
where this may happen\b you should
periodically check underneath the
car to be sure the movement of the
front wheels and the steering com
ponents is not obstructed.
Carry emergency equipment
Depending on the severity of the
weather\b you should carry appropri
ate emergency equipment. Some of
the items you may want to carry
include tire chains\b tow straps or
chains\b flashlight\b emergency flares\b
sand\b shovel\b jumper cables\b window
scraper\b gloves\b ground cloth\b cover
alls\b blanket\b etc.
Don't place foreign objects or materials in the engine compartment
Placement of foreign objects or
materials which prevent cooling of
the engine\b in the engine compart
ment\b may cause a failure or com
bustion. The manufacturer is not
responsible for the damage caused
by such placement.
!-0,0*&."'$-.,/#0%(/
+)

Page 287 of 400

Two labels on your driver’s door sill
show how much weight your vehicle
was designed to carry: the Tire and
Loading Information Label and the
Certification Label.
Before loading your vehicle\b familiar
ize yourself with the following terms
for determining your vehicle's weight
ratings\b from the vehicle's specifica
tions and the Certification Label:Base Curb Weight
This is the weight of the vehicle
including a full tank of fuel and all
standard equipment. It does not
include passengers\b cargo\b or option
al equipment.
Vehicle Curb Weight
This is the weight of your new vehicle
when you picked it up from your deal
er plus any aftermarket equipment.
Cargo Weight
This figure includes all weight added
to the Base Curb Weight\b including
cargo and optional equipment. GAW (Gross Axle Weight)
This is the total weight placed on
each axle (front and rear) including
vehicle curb weight and all payload.
GAWR (Gross Axle Weight Rating)
This is the maximum allowable
weight that can be carried by a single
axle (front or rear). These numbers
are shown on the Certification Label.
The total load on each axle must
never exceed its GAWR.
GVW (Gross Vehicle Weight)
This is the Base Curb Weight plus
actual Cargo Weight plus passen
gers.
GVWR (Gross Vehicle Weight
Rating)
This is the maximum allowable
weight of the fully loaded vehicle
(including all options\b equipment\b
passengers and cargo). The GVWR
is shown on the Certification Label
located on the driver’s door sill.Overloading
V'(!'
W'($
The Gross Axle Weight Rating
(GAWR) and the Gross Vehicle
Weight Rating (GVWR) for your
vehicle are on the Certification
Label attached to the driver's (or
front passenger’s) door.
Exceeding these ratings can
cause an accident or vehicle dam
age. You can calculate the weight
of your load by weighing the items
(and people) before putting them
in the vehicle. Be careful not to
overload your vehicle.
WARNING

!-0,0*&."'$-.,/#0%(/
+)

Page 288 of 400


  



 $$'$% %'$& !
%'$&'"'$%'&&&%' &'  % !

(%'('&"&'(!% !("'(#""& 
(%'('&"&'(!% !( %( (#$!!#$ ($#(#$!!"& 
($( '( ( %(%"#'("'(#""&
'#&'&% %&' '%"#'#$# !
(%'('&"&'($'!&%(%#&($'#( $#(%#&!($'#(!$
(%'('&"&'(%#&!($'#(&$# (
%($'!&%(!% #% 
'#$# % !
'#&'&% %&'"&&$# !!
'"'$&'$'$#'# & !
( &(%$$!( 

'$"&( &(!%$#"&(%'(! #'(%"#' 
 &"&(%"#'!( 
(
'  
" % !
$"&(!'#"' 

'$
'(%$"&($$( 
'#'&(%$"&( 


Page 289 of 400

The hazard warning flasher serves
as a warning to other drivers to exer-
cise extreme caution when
approaching, overtaking, or passing
your vehicle.
It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
To turn the hazard warning flasher
on or off, press the hazard warning
flasher button with the ignition switch
in any position. The button is located
in the center console switch panel. All turn signal lights will flash simul-
taneously.
• The hazard warning flasher oper-
ates whether your vehicle is run-
ning or not.
• The turn signals do not work when the hazard flasher is on."" " #$#"% !$#'#"'"' %'$%'&&&%
OIB067001

Page 290 of 400

IIf the engine stalls while driving• Reduce your speed gradually,
keeping a straight line. Move cau-
tiously off the road to a safe place.
• Turn on your hazard warning flash- er.
• Try to start the engine again. If your vehicle will not start, we recom-
mend that you contact an author-
ized HYUNDAI dealer.If the engine stalls at a cross-
road or crossing If the engine stalls at a crossroad or
crossing, if safe to do so, move the
shift lever to the N (Neutral) position
and then push the vehicle to a safe
location.
• If your vehicle has a manual transaxle not equipped with a igni-
tion lock switch, the vehicle can
move forward by shifting to the
2(second) or 3(third) gear and then
turning the starter without depress-
ing the clutch pedal.
If you have a flat tire while driv-
ing If a tire goes flat while you are driv-
ing:
• Take your foot off the accelerator
pedal and let the vehicle slow
down while driving straight ahead.
Do not apply the brakes immedi-
ately or attempt to pull off the road
as this may cause loss of vehicle
control resulting in an accident.
When the vehicle has slowed to
such a speed that it is safe to do
so, brake carefully and pull off the
road. Drive off the road as far as
possible and park on firm, level
ground. If you are on a divided
highway, do not park in the median
area between the two traffic lanes.
• When the vehicle is stopped, press the hazard warning flasher button,
move the shift lever into P (Park,
for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), apply the park-
ing brake, and place the ignition
switch in the LOCK/OFF position. • Have all passengers get out of the
vehicle. Be sure they all get out on
the side of the vehicle that is away
from traffic.
• When changing a flat tire, follow the instructions provided later in
this chapter.
$#"%"#%% %#$% $$#
!

$#'#"'"' %'$%'&&&%

Page:   < prev 1-10 ... 241-250 251-260 261-270 271-280 281-290 291-300 301-310 311-320 321-330 ... 400 next >