light HYUNDAI I20 2015 Workshop Manual

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3AUTO light position (if equipped)When the light switch is in the AUTO
position, the parking (position) light
and headlights will be turned ON or
OFF automatically depending on the
amount of light outside the vehicle.
Even with the AUTO light feature in
operation, it is recommended to
manually turn ON the lights when
driving at night or in a fog, or when
you enter dark areas, such as tun-
nels and parking facilities. •
•
Do not cover or spill anything on
the sensor (1) located on the
instrument panel.
• Do not clean the sensor using a win- dow cleaner, the cleanser may
leave a light film which could inter-
fere with sensor operation.
• If your vehicle has window tint or other types of metallic coating on
the front windshield, the AUTO
light system may not work proper-
ly.
High beam operationTo turn on the high beam headlamp,
push the lever away from you. The
lever will return to its original position.
The high beam indicator will light
when the headlamp high beams are
switched on.
To turn off the high beam headlamp,
pull the lever towards you. The low
beams will turn on.
NOTICE
OLF044192R
OLF044085R
Do not use high beam when there
are other vehicles approaching you.
Using high beam could obstruct the
other driver's vision.
WARNING

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
To flash the high beam headlights,
pull the lever towards you, then
release the lever. The high beams
will remain ON as long as you hold
the lever towards you.
TT urn signals and lane change sig-
nalsTo signal a turn, push down on the
lever for a right turn or up for a left
turn in position (A). To signal a lane
change, move the turn signal lever
slightly and hold it in position (B). The
lever will return to the OFF position
when released or when the turn is
completed.
If an indicator stays on and does not flash or if it flashes abnormally, one ofthe turn signal bulbs may be burned
out and will require replacement.
One-touch lane change function
(if equipped)To activate an One-Touch Lane
Change function, move the turn sig-
nal lever slightly and then release it.
The lane change signals will blink 3,
5 or 7 times.
You can activate/deactivate the One
Touch Turn Signal function or choose
the number of blinking (3, 5, or 7)
from the User Settings Mode on the
LCD display.For more details, refer to "LCD
Display" in this chapter.
If the turn signal indicator stays on
and does not flash, or if it flashes
abnormally, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit. The bulb may
require replacement.NOTICE
OLF044088R
OLF044091R

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3FFront fog light (if equipped) Fog lights are used to provide
improved visibility when visibility is
poor due to fog, rain or snow, etc.
1. Turn on the park light.
2. Move the light switch (1) to the
front fog light position.
3. To turn off the front fog light, turn the light switch to the front fog light
position again or turn off the park-
ing light.
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor.
Battery saver functionThe purpose of this feature is to pre-
vent the battery from being dis-
charged. The system automatically
turns off the parking lights when the
driver removes the ignition key or
turns the engine off (for smart key)
and opens the driver-side door.
With this feature, the parking lights
will turn off automatically if the driver
parks on the side of road at night.
If necessary, to keep the lights on
when the ignition key is removed or
the engine is turned off (for smart
key), perform the following:
1) Open the driver-side door.
2) Turn the parking lights OFF and ON again using the light switch on
the steering column.
NOTICE
OIB047008R

)')
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
HHeadlamp delay function
(if equipped)If the key is removed from the ignition
switch or placed in the ACC or
LOCK/OFF position with the head-
lights ON, the headlights (and/or
parking lights) remain on for about 5
minutes. However, with the engine off
if the driver’s door is opened and
closed, the headlights (and/or parking
lights) are turned off after 15 seconds.
The headlights (and/or parking
lights) can be turned off by pressing
the lock button on the remote key (or
smart key) twice or turning the light
switch to the OFF or AUTO position.
However, if you turn the light switch
to the AUTO position when it is dark
outside, the headlights will not be
turned off.
If the driver gets out of the vehicle
through other doors (except driver's
door), the battery saver function
does not operate and the headlamp
delay function does not turn off auto-
matically. Therefore, It causes the
battery to be discharged. In this
case, make sure to turn off the lamp before getting out of the vehicle.
Headlight leveling device (if equipped)To adjust the headlight beam level
according to the number of the pas-
sengers and loading weight in the
luggage area, turn the beam leveling
switch.
NOTICE
OIB044009

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
The higher the number of the switch
position, the low er the headlight
beam level. Always keep the head-
light beam at the proper leveling
position, or headlights may dazzle
other road users.
Listed below are the examples of
proper switch settings. For loading
conditions other than those listed
below, adjust the switch position so
that the beam level may be the near-
est as the condition obtained accord-
ing to the list.
DD aytime running light (DRL)
(if equipped)The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and before
sunset.
The DRL system will turn the dedi-
cated lamp OFF when:
1. The headlights or front fog lights
are in the ON position.
2. The engine is turned off.
Interior lightsDo not use the interior lights for
extended periods when the engine is
turned off or the battery will dis-
charge.Interior lamp AUTO cutThe interior lamps will automatically
go off approximately 20 minutes after
the engine is turned off and the
doors closed. If a door is opened, the
lamp will go off 40 minutes after the
engine is turned off. If the doors are
locked by the remote key or smart
key and the vehicle enters the armed
stage of the theft alarm system, the
lamps will go off five seconds later.NOTICEDo not use the interior lights when
driving in the dark. The interior
lights may obscure your view and
cause an accident.
WARNING
Loading condition Switch position
Driver only 0
Driver + Front passenger 0
Full passengers
(including driver) 1
Full passengers (including
driver) + Maximum permis-
sible loading 2
Driver + Maximum permis-
sible loading 3

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
FFront lamps(1) Front Map Lamp
(2) Front Room LampFront Map Lamp:Press either the right or left lens to
turn the map lamp on or off. This light
produces a spot beam for convenient
use as a map lamp at night or as a
personal lamp for the driver and the
front passenger.
Front Room Lamp:The Front Room Lamp Switch acti-
vates the front and rear room lamps
when the switch is pressed in either of
the three positions indicated below:
: The front or rear room lampscome on when the front or
rear doors are opened if the
engine is running or not. When
doors are unlocked by the
remote key or smart key, the
front and rear lamps come on
for approximately 15 seconds
as long as any door is not
opened. The front and rear
room lamps go out gradually
after approximately 15 sec-
onds if the door is closed.
However, if the ignition switch
is in the ON position or all
doors are locked, the front and
rear lamps will turn off imme-
diately. If a door is opened with
the ignition switch in the ACC
position or the LOCK/OFF
position, the front and rear
lamps stay on for about 20
minutes. However, if a door is
opened with the ignition switch
in the ON position, the lamps
stays on continuously. : With the Front Room Lamp in
this position, the front and
rear room lamps remain on
at all times.
: With the Front Room Lamp in this position the front and
rear room lamps remain off
at all times.
Information
When the map lamp (1) is turned ON
by pressing the lens, the map lamp
will not turn off even if the front room
lamp switch is in the OFF position.i
OIB044015

)' )
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
WWhen using the air conditioning sys-
tem, monitor the temperature gauge
closely while driving up hills or in
heavy traffic when outside tempera-
tures are high. Air conditioning sys-
tem operation may cause engine
overheating. Continue to use the
blower fan but turn the air condition-
ing system off if the engine tempera-
ture gauge indicates engine over-
heating.
Air conditioning system operation
tips • If the vehicle has been parked in direct sunlight during hot weather,
open the windows for a short time
to let the hot air inside the vehicle
escape.
• After sufficient cooling has been achieved, switch back from the
recirculated air to the fresh outside
air position.
• To help reduce moisture inside of the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the win-
dows closed.
• Use the air conditioning system every month only for a few minutes
to ensure maximum system per-
formance. • If you operate air conditioner
excessively, the difference between
the temperature of the outside air
and that of the windshield could
cause the outer surface of the
windshield to fog up, causing loss
of visibility. In this case, set the
mode selection knob or button to
the position and fan speed
control to the lower speed.
NOTICE

#!'%$&%" '&$
(6) S
S
EEK/TRACK
• When pressed quickly
- Radio mode: Searches broadcastfrequencies saved to Presets.
- Media mode: Changes track, file or title. (except AUX)
• When pressed and held (more than 1.0 second)
- Radio mode: Frequency is con-trolled by 1 step quickly. When
the button is released after
pressing and holding, searches
broadcast frequencies.
- Media mode: Rewinds or fast-for- wards the song. (except BT
Audio*, AUX)
* if equipped
• Do not stare at the screen while driving. Staring at the screen for
prolonged periods of time could
lea d to traffic accidents.
• Do not disassemble, assemble, or modify the audio system.
Such acts could result in acci-
dents, fire, or electric shock.
• Using the phone while driving may lead to a lack of attentio n of
traffic conditions and increase
the likelihood of accidents. Use
the phone feature after parking
the vehicle.
• Heed caution not to spill water or introduce foreign objects into
the device. Such acts could lead
to smoke, fire, or product mal-
function.
(Continued)
WARNING
(Continued)
• Please refrain from use if the screen is blank or no sound can
be heard as these signs may
i ndicate product malfunction.
Continued use in such condi-
tions could lead to accidents
(fires, electric shock) or product
malfunctions.
• Do not touch the antenna during thunder or lightening as such
acts may lead to lightning
induced electric shock.
• Do not stop or park in parking- restricted areas to operate the
product. Such acts could lead to
traffic accidents.
• Use the system with the vehicle ignition turned o n. Prolonged
use with the ignition turned off
could result in battery discharge.

#!'%$&%" '&$
(5) M
M
ODE
• If any media is connected, each
time this is pressed, it toggles
between the connected media
modes & radio modes (FM, AM,
DRM).
• If no media is connected, each time this is pressed, it toggles
between the radio modes (FM ➟
AM ➟DRM ➟FM).
• Press and hold the button to turn off.
(6)
UP/DOWN
• Press the button in radio mode to cycle between the FM/AM and
DRM frequencies in the order as
stored in the presets.
• Press and hold the button in radio mode to search for the next avail-
able frequency.
• Press the button in media mode to change the current song. (except
AUX)
• Press and hold the button in media mode to quick search through
songs. (except Bluetooth
®(BT)
Audio and AUX)
• Do not stare at the screen while driving. Staring at the screen for
prolonged periods of time could
lea d to traffic accidents.
• Do not disassemble, assemble, or modify the audio system.
Such acts could resul t in acci-
dents, fire, or electric shock.
• Using the phone while driving may lead to a lack of attention of
traffic conditions and increase
the likelihood of accidents. Use
the phone feature after parking
the vehicle.
• Exercise caution not to spill water or introduce foreign
objects into the device. Such
acts co uld lead to smoke, fire, or
product malfunction.
(Continued)
WARNING
(Continued)
• Please refrain from use if the screen is blank or no sound can
be heard as these signs may
i ndicate product malfunction.
Continued use in such conditions
could lead to accidents (fires,
electric s hock) or product mal-
functions.
• Do not touch the antenna during thunder or lightening as such
acts may lead to lightning
induced electric shock.
• Do not stop or park in parking- restricted areas to operate the
product. Such acts could lead to
traffic accidents.
• Use the system with the vehicle engine turned o n. Prolonged
use with the ignition turned on
only could result in battery dis-
charge.

#!'%$&%" '&$DDRM Mode❈ The actual features may differ
from the illustration. May change
according to the transmission con-
tent of DRM.(1) BandSwitch between FM, AM and DRM.(2) PresetsView all presets.(3) Services

Cycle between the services available
with the broadcasting frequency.
(4) MenuNavigate to the menu screen.(5) No signalWhen no signal or weak signal in
DRM Mode, Display No signal icon.(6) Services Index• Displays the number of services available with the broadcasting fre-
quency.
• Highlights the currently receiving service.
• No. of services depends on the broadcasting station and it may
vary from 1 ~ 4.(7) Text InformationText Information may or may not be
available and it depends on the
broadcasting station.
Switching between FM, AM and DRM• Press the
[RADIO]
button on the
audio system to switch between
FM, AM and DRM.
• Select [Band] on the screen to switch between FM, AM and DRM.
Searching stationsPress the
[SEEK/TRACK]
button to
search stations.
PresetsSave up to 40 frequently used stations.
To listen to a preset, select the
desired station list.
Press and hold the desired slot from
1 through 40. This saves the current
station in the selected slot.
If the slot is empty, simply selecting
saves the station to the slot.Changing Service• Select [Services ] in order to
cycle between the available servic-
es from 1 ➟ 2 ➟ 3 ➟ 4 ➟ 1.
• Number of services depends on the broadcasting station and can
vary between 1 ~ 4.