bulb HYUNDAI I20 2015 Owners Manual



Hyundai Motor India Limited here-
inafter called "HMIL", warrants that
each new Hyundai vehicle sold shall
be free from any defects in material
and workmanship, under normal use
and maintenance, subject to the fol-
lowing terms and conditions.
1. Warranty period This warranty shall exist for a period
of
36 months/100,000 kms whichsoever is

earlier from the date
of delivery to the first purchaser.
This warranty is transferab
le to
subsequent owner for the remaining
warranty period. This warranty is
applicable only in India and
not
transferable to any other country.
2. What is covered
Except as provided in paragraph 3
hereof, our Authorized Dealers shall
either repair or replace, any Hyundai
genuine part that is acknowledged
by HMIL to be defective in material or w

orkmanship within the warranty
period stipulated above, at no cost to
the owner of the Hyundai vehicle for
parts or labour. Such defective parts
which have been replaced will
become the property of HMIL.
3. What is not covered
This warranty shall not apply to:
o Normal maintenance services other than the three free services,
including without limitation, clean-
ing and polishing, minor adjust-
ments, engine tuning, oil/fluid
changes, filters replenishment,
fastener retightening, wheel bal-
ancing, wheel alignment and tyre
rotation etc.
o Replacement of parts as a result of normal wear and tear such as
spark plugs, belts, brake pads
and linings, clutch disc/facing, fil-
ters, wiper blades, bulbs, fuses,
etc.
o Damage or failure resulting from: Negligence of proper mainte-
nance as required in this
Owner's Manual and Service
Booklet.
 Misuse, abuse, accident, theft, flooding or fire.
 Use of improper or insufficient
fuel, fluids or lubricants.
 Use of parts other than
Hyundai Genuine Parts.
 Any device and/or accessories
not supplied by HMIL.
 Modifications, alterations,
tampering or improper repair.
 Parts used in applications of
which they were not designed
or not approved by HMIL.
 Slight irregularities not recog-
nised as affecting quality or
function of the vehicle or parts,
such as slight noise or vibra-
tions, or items considered
characteristic of the vehicle.
 Airborne "fallout", Industrial
fall out, acid rain, hail and wind
storms, or other Acts of God.
 Paint scratches, dents or simi-
lar paint or body damage.
 Action of road elements (sand,
gravel, dust or road debris)
which results in stone chipping
of paint or glass.
22
Hyundai Warranty Policy
IBi Eng 2_PA RHD 1.qxd 18-03-2016 16:49 Page 2

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
To flash the high beam headlights,
pull the lever towards you, then
release the lever. The high beams
will remain ON as long as you hold
the lever towards you.
TT urn signals and lane change sig-
nalsTo signal a turn, push down on the
lever for a right turn or up for a left
turn in position (A). To signal a lane
change, move the turn signal lever
slightly and hold it in position (B). The
lever will return to the OFF position
when released or when the turn is
completed.
If an indicator stays on and does not flash or if it flashes abnormally, one ofthe turn signal bulbs may be burned
out and will require replacement.
One-touch lane change function
(if equipped)To activate an One-Touch Lane
Change function, move the turn sig-
nal lever slightly and then release it.
The lane change signals will blink 3,
5 or 7 times.
You can activate/deactivate the One
Touch Turn Signal function or choose
the number of blinking (3, 5, or 7)
from the User Settings Mode on the
LCD display.For more details, refer to "LCD
Display" in this chapter.
If the turn signal indicator stays on
and does not flash, or if it flashes
abnormally, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit. The bulb may
require replacement.NOTICE
OLF044088R
OLF044091R

1.$
,204/3424-3
Diesel Engine
Never work on injection system
with engine running or within 30
seconds after shutting of f engine.
High-pressure pump, rail, injectors
and high-pressure pipes are sub-
ject to high pressure eve n after
the engine stopped. The fuel jet
produced by fuel leaks may cause
serious injury, if it touches the
body. People using pacemakers
should not move more than 30cm
closer to the ECU or wiring har-
ness wi thin the engine room while
engine is running, since the high
currents in the electronic engine
control s ystem produce consider-
able magnetic fields.
WARNING
(Continued)
• When you remove the interior trim cover with a flat head (-) driver, be
careful not to dama ge the cover.
• Be careful when you replace and clean bulbs to avoid burns or elec-
trical shock.
Engine compartment precautions
(Diesel engine)• The injector operates at high volt-
age (maximum 200v). Therefore,
the following accidents may occur.
- Direct contact with the injector orinjector wiring may cause electric
shock or damage your muscle or
nerve system.
- The electromagnetic wave from the operating injector may cause
the artificial heart pacemaker to
malfunction.
• Follow the safety tips provided below, when you are checking the
engine room while the engine is
running.
- Do not touch the injector, injectorwirings, and the engine computer
while the engine is running.
- Do not remove the injector con- nector while the engine is run-
ning.
- People using pacemakers must not go near the engine while the
engine is starting or running.

1.$#,204/3424-3!#Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference
between the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur-
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit-
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause dam -
age to the fuse or electric wiring sys-
tem.
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for Continuo usly
Variable Transaxle vehicle) or
neutral (for Manual Transaxle
vehicle), apply the parking brake,
plac e the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the
vehicle to av oid sudden move-
ment of the vehicle and to prevent
possible electric shock.
Be aware the bulbs may be h ot
and may burn your fingers.
WARNING

1.$$
,204/3424-3
HHeadlight, Parking (Position)
Light, Turn signal Light, Low
Beam Assist-Static Light, Fog
Light and Daytime Running Light
bulb replacement(1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Daytime Running Light
(if equipped)
(5) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector) Headlight (1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight (1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector)
Headlight
OIB077068
■ 5 Door
• Type A
OIB077069
■5 Door
• Type B
OIB077070
■Cross
• Type A

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross

1.'&
,204/3424-3
1. Remove the under cover by rotat-ing the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulb-socket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
PPosition light/Daytime running light(if equipped)Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, we recommend
that the vehicle be checked by an
authorized HYUNDAI dealer.
Side repeater light (LED)
replacement (if equipped)If the light does not operte, we rec-
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
OIB074035

1.'),204/3424-3
1. Using a flat-blade screwdriver, remo ve the light assembly from
the body of the vehicle by prying
the housing and pulling the
assembly out.
2. Separate the socket and the lens part by turning the socket counter-
clockwise until the tabs on the
socket align with the slots on the
lens part.
3. Remove the bulb by pulling it straight out.
4. Insert a new bulb in the socket.
5. Reassemble the socket and the housing part.
6. Reinstall the light assembly to the body of the vehicle.
IInterior light bulb replacement1. Using a flat-blade screwdriver,
gently pry the lens from the interi-
or light housing. 2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap
the lens into place.
Be careful not to dirty or damage
lens, lens tab, and plastic housings. NOTICE
■ Room lamp■Luggage room lamp
OIB074042OIB074041
OIB074040
■Cross