charging HYUNDAI I20 2020 Owners Manual

5-12
Instrument cluster
Charging System
Warning Light
This warning light illuminates:
• Once you set the ignition switch or
Engine Start/Stop button to the ON
position.
- It remains on until the engine is
started.
• When there is a malfunction with
either the alternator or electrical
charging system.
If there is a malfunction with either
the alternator or electrical charging
system:
1. Drive carefully to the nearest safe
location and stop your vehicle.
2. Turn the engine off and check the
alternator drive belt for looseness or
breakage.
If the belt is adjusted properly, there
may be a problem in the electrical
charging system.
In this case, we recommend that you
have the vehicle inspected by an
authorized HYUNDAI dealer as soon as
possible.
Engine Oil Pressure
Warning Light
This warning light illuminates:
• Once you set the ignition switch or
Engine Start/Stop button to the ON
position.
- It remains on until the engine is
started.
• When the engine oil pressure is low.
If the engine oil pressure is low:
1. Drive carefully to the nearest safe
location and stop your vehicle.
2. Turn the engine off and check the
engine oil level (For more details, refer
to “Engine Oil” in chapter 9). If the
level is low, add oil as required.
If the warning light remains on after
adding oil or if oil is not available, we
recommend that you have the vehicle
inspected by an authorized HYUNDAI
dealer as soon as possible.

5-28
Instrument cluster
Convenience
ItemsExplanation
Welcome
mirror/light• On door unlock: The outside rearview mirrors are unfolded and the
welcome light turns on automatically when the doors are unlocked.
• On driver approach: The outside rearview mirrors are unfolded and the
welcome light turns on automatically when the vehicle is approached
with the smart key.
For more details, refer to ‘’Welcome System’’ in chapter 5.
Wireless
charging systemTo activate or deactivate the wireless charging system in the front seat.
For more details, refer to “Wireless cellular phone charging system” in
chapter 5.
Wiper/Lights
displayTo activate or deactivate the Wiper/ Light mode.
When activated, the LCD display shows the selected Wiper/Light mode
whenever you changed the mode.
Service interval
ItemsExplanation
Service IntervalIn this mode, you can activate the service interval function with mileage
(km or mi.) and period (months).• Off : The service interval function will be deactivated.
• On :You can set the service interval (mileage and months).

6
Wipers and washers ......................................................................................6-50
Windshield wipers ................................................................................................... 6-51
Windshield washers ................................................................................................ 6-51
Rear window wiper and washer switch ................................................................. 6-52
Manual climate control system .................................................................... 6-53
Heating and air conditioning .................................................................................. 6-54
System operation .................................................................................................... 6-58
System maintenance ..............................................................................................6-60
Automatic climate control system ............................................................... 6-62
Automatic heating and air conditioning ................................................................ 6-63
Manual heating and air conditioning ..................................................................... 6-64
System operation .................................................................................................... 6-69
System maintenance
............................................................................................... 6-71
Windshield defrosting and defogging ......................................................... 6-72
Manual climate control system ...............................................................................6-72
Automatic climate control system ..........................................................................6-73
Auto defogging system (only for automatic climate control system)
..................6-74
Defroster ...................................................................................................................6-75
Storage compartment ...................................................................................6-77
Center console storage ............................................................................................ 6-77
Sliding armrest
......................................................................................................... 6-77
Glove box ................................................................................................................. 6-78
Cool box ................................................................................................................... 6-78
Interior features ........................................................................................... 6-79
Cup holder ............................................................................................................... 6-79
Sunvisor ...................................................................................................................6-80
Power outlet ............................................................................................................6-80
USB charger
..............................................................................................................6-81
Clothes hanger ........................................................................................................ 6-82
Wireless cellular phone charging system .............................................................. 6-82
Floor mat anchor(s) ................................................................................................. 6-85
Cargo area cover
.....................................................................................................6-86

6-20
Convenient features
Electric power steering (EPS)
The system assists you with steering
the vehicle. If the engine is off or if
the power steering system becomes
inoperative, the vehicle may still be
steered, but it will require increased
steering effort.
Also, the steering effort becomes
heavier as the vehicle’s speed increases
and becomes lighter as the vehicle’s
speed decreases for better control of the
steering wheel.
Should you notice any change in the
effort required to steer during normal
vehicle operation, we recommend that
the system be checked by an authorized
HYUNDAI dealer.
NOTICE
If the Electric Power Steering System
does not operate normally, the
warning light (
) will illuminate on
the instrument cluster. The steering
wheel may become difficult to control
or operate. Take your vehicle to an
authorized HYUNDAI dealer and
have the system checked as soon as
possible.
i Information
The following symptoms may occur
during normal vehicle operation:
• The steering effort may be high
immediately after placing the ignition
switch in the ON position.
This happens as the system performs
the EPS system diagnostics. When
the diagnostics is completed, the
steering wheel will return to its normal
condition.
• When the battery voltage is low, you
might have to put more steering effort.
However, it is a temporary condition so
that it will return to normal condition
after charging the battery.
• A click noise may be heard from the
EPS relay after the ignition switch
is placed to the ON or LOCK/OFF
position.
• Motor noise may be heard when the
vehicle is at stop or at a low driving
speed.
• When you operate the steering wheel
in low temperature, abnormal noise
may occur. If temperature rises, the
noise will disappear. This is a normal
condition.
WARNING
Never adjust the steering wheel while
driving. You may lose steering control
and cause severe personal injury, death
or accidents.
STEERING WHEEL

6-49
06
OCN7050057OCN7050057
„„Type BType B
Rear Interior Lamp Switch ():
Press this button to turn the interior
lamp on and off.
Luggage compartment lamp
OBC3050032OBC3050032
The luggage compartment lamp comes
on when the tailgate is opened.
NOTICE
The luggage compartment comes on
as long as the tailgate lid is open. To
prevent unnecessary charging system
drain, close the tailgate lid securely
after using the tailgate.
Welcome system
OBI3050072LOBI3050072L
Welcome system helps keep the driver
visible by turning on vehicle lights when
the driver approaches the vehicle.
Puddle lamp (if equipped)
When the ignition switch is in the OFF
position and the driver’s door is opened,
the puddle lamp will come ON for 30
seconds. If the driver’s door is closed
within the 30 seconds, the puddle lamp
will turn off after 15 seconds.
If the driver’s door is closed and
locked, the puddle lamp will turn off
immediately.
When all the doors (and tailgate) are
closed and locked, the puddle lamp will
come on for about 15 seconds if any of
the below is performed.
• When the door unlock button is
pressed on the smart key
• When the button of the outside door
handle is pressed
• When the vehicle is approached
with the smart key in possession (if
equipped)
$OVRLI
U&RQYHQLHQFH

6-81
06
NOTICE
To prevent damage to the Power outlet:
• Use the power outlet only when the
engine is running and remove the
accessory plug after use. Using the
accessory plug for prolonged periods
of time with the engine off could
cause the battery to discharge.
• Only use 12V electric accessories
which are less than 180W (Watt) in
electric capacity.
• Adjust the air-conditioner or heater
to the lowest operating level when
using the power outlet.
• Close the cover when not in use.
• Some electronic devices can cause
electronic interference when plugged
into a vehicle’s power outlet. These
devices may cause excessive audio
static and malfunctions in other
electronic systems or devices used in
your vehicle.
• Push the plug in as far as it will go.
If good contact is not made, the
plug may overheat or the internal
temperature fuse may open.
• Plug in battery equipped electrical/
electronic devices with reverse
current protection. The current
from the battery may flow into the
vehicle’s electrical/electronic system
and cause system malfunction.
USB charger (if equipped)
OBI3050071OBI3050071
„„FrontFront
„„RearRear
OBI3050058OBI3050058
The USB charger is designed to recharge
batteries of small size electrical devices
using a USB cable.
The electrical devices can be recharged
when the Engine Start/ Stop button is in
the ACC, ON or START position.
The battery charging state may be
monitored on the electrical device.
Disconnect the USB cable from the USB
port after use.
• A smart phone or a tablet PC may
get warmer during the re-charging
process. It does not indicate any
malfunction with the charging system.
• A smart phone or a tablet PC, which
adopts a different re-charging
method, may not be properly
re-charged. In this case, use an
exclusive charger of your device.
• The charging terminal is only to
recharge a device. Do not use the
charging terminal either to turn ON
an audio or to play media on the
infotainment system.

6-82
Convenient features
Clothes hanger (if equipped)
OIB044031OIB044031
These hangers are not designed to hold
large or heavy items.
WARNING
OIB047192OIB047192
Do not hang other objects such
as hangers or hard objects except
clothes. Also, do not put heavy, sharp
or breakable objects in the clothes
pockets. In an accident or when the
curtain air bag is inflated, it may cause
ve-hicle damage or personal injury.
Wireless cellular phone charging
system (if equipped)
OBI3050057OBI3050057
[A] : Charging pad
There is a wireless cellular phone
charger inside the front console.
The system is available when all doors
are closed, and when the ignition switch
is in the ON position.

6-83
06
To charge a cellular phone
The wireless cellular phone charging
system charges only the Qi-enabled
cellular phones (
). Read the label on
the cellular phone accessory cover or
visit your cellular phone manufacturer’s
website to check whether your cellular
phone supports the Qi technology.
The wireless charging process starts
when you put a Qi-enabled cellular
phone on the wireless charging unit.
1. Remove other items, including the
smart key, from the wireless charging
unit. If not, the wireless charging
process may be interrupted. Place
the cellular phone on the center of
charging pad.
2. You can turn ON or OFF the wireless
charging function in the User Settings
mode on the instrument cluster. For
further information, refer to the “LCD
Display Modes” in chapter 4.If your cellular phone is not charging:
- Slightly change the position of the
cellular phone on the charging pad.
- Make sure the indicator light is orange.
The ERROR symbol will blink/flash for
10seconds and turn off if there is a
malfunction in the wireless charging
system.
In this case, temporarily stop the
charging process, re-attempt to
wirelessly charge your cellular phone
and then check the charging status
again.
The system warns you with a message
on the LCD display if the cellular phone
is still on the wireless charging unit after
the engine is turned OFF and the front
door is opened.
For some manufacturers’ cellular
phones, the system may not warn you
even though the cellular phone is left on
the wireless charging unit. This is due
to the particular characteristic of the
cellular phone and not a malfunction of
the wireless charging.
CAUTION
To prevent liquid from damaging
the wireless cellular phone charging
system in your vehicle, be sure not to
spill liquid over the pad when charging
your cellular phone.

6-84
Convenient features
NOTICE
• The wireless cellular phone charging
system may not support certain
cellular phones, which are not
verified for the Qi specification (
).
• When placing your cellular phone on
the charging mat, position the phone
in the middle of the mat for optimal
charging performance. If your cell
phone is off to the side, the charging
rate may be less and in some cases
the cell phone may experience higher
heat conduction.
• In some cases, the wireless charging
may stop temporarily when the
Remote Key or Smart Key is used,
either when starting the vehicle or
locking/unlocking the doors, etc.
• When charging certain cellular
phones, the charging indicator may
not change to green when the cell
phone is fully charged.
• The wireless charging process may
temporarily stop, when temperature
abnormally increases inside the
wireless cellular phone charging
system. The wireless charging
process restarts, when temperature
falls to a certain level.
• The wireless charging process may
temporarily stop when there is
any metallic item, such as a coin,
between the wireless cellular phone
charging system and a cellular
phone. In this case, immediately
remove a cellular phone from the pad
and remove coin after completely
cooling down. • When charging some cellular phones
with a self-protection feature,
the wireless charging speed may
decrease and the wireless charging
may stop.
• If the cellular phone has a thick
cover, the wireless charging may not
be possible.
• If the cellular phone is not completely
contacting the charging pad, wireless
charging may not operate properly.
• Some magnetic items (credit cards,
phone cards, passbook and tickets)
may be damaged while using the
wireless charging process.
• When any cellular phone without
a wireless charging function or a
metallic object is placed on the
charging pad, a small noise may
sound. This small sound is due to the
vehicle discerning compatibility of
the object placed on the charging
pad. It does not affect your vehicle or
the cellular phone in any way.
• Some cellular phones may not be
able to put on the charging pad due
to their size. In this case, wireless
charging may be limited.
• For some manufactures’ cellular
phones, the system may not warn
you even though the cellular phone is
left on the charging pad.
This is due to the particular
characteristic of the cellular phone
and not a malfunction of the wireless
charging.
i Information
If the ignition switch is in the LOCK/OFF
position, the charging also stops.

6-105
06
Restarting the current playback
On the control panel after the song has
played for 2 seconds, press the [< SEEK]
button.
• You can also push the Up lever on the
steering wheel.
Playing the previous or next song
To play the previous song on the control
panel within the first 2 seconds of the
current song, press the [< SEEK] button.
To play the next song, press the [TRACK >]
button on the control panel.
• If more than 2 seconds of playback
have elapsed, press the [< SEEK]
button on the control panel twice to
play the previous song.
• You can also push the Up/down lever
on the steering wheel.
NOTICE
Press the [MENU/CLOCK] button on
the control panel to display the mode
selection window, turn the [TUNE] knob
to find the desired song and press the
knob to play the file.
Playing repeatedly
On the control panel, press the [1 RPT]
button. The corresponding mode icon
will be displayed on the screen and the
playing song will be repeated.
Playing in random order
On the control panel, press the
[2 SHFL] button. The shuffle play mode is
activated or deactivated each time you
press it. When you activate the shuffle
mode, the corresponding mode icon will
be displayed on the screen. When shuffle
is active, the available songs will be
played randomly.
NOTICE
Depending on the connected Bluetooth
device or mobile phone, repeat &
shuffle order features may not be
supported.
Searching folders
1. On the control panel, press the
[MENU/CLOCK] button.
2. When the option selection window
displays, turn the [TUNE] knob to
select the Folder list and then press
the knob.
3. Navigate to the desired folder in the
Folder list and then press the [TUNE]
knob.
• The first song in the selected folder
will be played.
i Information
• Start the engine of your vehicle before
connecting a USB device to your
system. Starting the engine with a USB
device connected to the system may
damage the USB device.
• Be careful of static electricity when
connecting or disconnecting a USB
device. A static discharge may cause a
system malfunction.
• Be careful not to let your body or
external objects contact the USB port.
Doing so may cause an accident or a
system malfunction.
• Do not connect and disconnect a USB
connector repeatedly in a short time.
Doing so may cause an error in the
device or a system malfunction.
• Do not use a USB device for purposes
other than playing files. Using USB
accessories for charging or heating may
cause poor performance or a system
malfunction.