battery HYUNDAI PALISADE 2023 Owners Manual

Page 12 of 661

01
1-7
VEHICLE MODIFICATIONS
[This vehicle should not be modified. Modification of your vehicle could affect its
performance, safety or durability and may even violate governmental safety and
emissions regulations.
[ In addition, damage or performance problems resulting from any modification may
not be covered under warranty.
[ If you use unauthorized electronic devices, it may cause the vehicle to operate
abnormally, wire damage, battery discharge and fire. For your safety, do not use
unauthorized electronic devices.
NOTICE
Some warning sounds (including welcome/good-bye sound, etc.) are generated
from the interior speakers or amplifiers. If necessary, we recommend you to
purchase HYUNDAI Part to replace an interior speaker or amplifier. Any unauthorized
product may cause a malfunction of the interior speakers or amplifiers.
9(+,&/(%5($.

Page 20 of 661

2-7
02
The actual engine compartment in the vehicle may differ from the illustration.
A0419KO02
1. Engine coolant reservoir ........................ 9-3
2. Radiator cap ...........................................9-18
3. Brake fluid reservoir .............................. 9-21
4. Air cleaner ............................................. 9-23
5. Engine oil filler cap ................................ 9-156. Engine oil dipstick ................................. 9-15
7. Windshield washer fluid reservoir ....... 9-22
8. Fuse/relay box ...................................... 9-46
9. Battery ................................................... 9-28
ENGINE COMPARTMENT

Page 37 of 661

03
3-7
Front Seats
WARNING
Take the following precautions when
adjusting your seat:
[NEVER attempt to adjust the seat
while the vehicle is moving. The seat
could respond with unexpected
movement and may cause loss
of vehicle control resulting in an
accident.
[ Do not place anything under the
front seats. Loose objects in the
driver’s foot area could interfere
with the operation of the foot pedals,
causing an accident.
[ Do not allow anything to interfere
with the normal position and proper
locking of the seatback.
[ Do not place a cigarette lighter on
the floor or seat. When you operate
the seat, gas may exit out of the
lighter causing a fire.
[ Use extreme caution when picking
up small objects trapped under the
seats or between the seat and the
center console. Your hands might be
cut or injured by the sharp edges of
the seat mechanism.
[ If there are occupants in the rear
seats, be careful while adjusting the
front seat position.
[ Make sure that the seat is locked in
place after the adjustment. If not,
the seat might move unexpectedly
resulting in an accident.
CAUTION
To prevent injury:
[Do not adjust your seat while
wearing your seat belt. Moving the
seat cushion forward may cause
strong pressure on your abdomen.
[ Do not allow your hands or fingers to
get caught in the seat mechanisms
while the seat is moving.
WARNING
NEVER allow children in the vehicle
unattended. The power seats are
operable when the vehicle is turned off.
NOTICE
To prevent damage to the seats:
[Always stop adjusting the seats when
the seat has been adjusted as far
forward or rearward as possible.
[ Do not adjust the seats longer than
necessary when the vehicle is turned
off. This may result in unnecessary
battery drain.
[ Do not operate two or more seats at
the same time. This may result in an
electrical malfunction.

Page 39 of 661

03
3-9
Seat belts must be snug against your
hips and chest to work properly. When
the seatback is reclined, the shoulder
belt cannot do its job because it will not
be snug against your chest. Instead,
it will be in front of you. During an
accident, you could be thrown into the
seat belt, causing neck or other injuries.
The more the seatback is reclined,
the greater chance the passenger's
hips will slide under the lap belt or the
passenger's neck will strike the shoulder
belt.
B0052KO04
Seat cushion height
To change the height of the seat cushion:
[Push do

wn the lever several times, to
lower the seat cushion.
[ Pull up the lever several times, to raise
the seat cushion.
Power adjustment (if equipped)
The front seat can be adjusted by using
the control switches located on the
outside of the seat cushion. Before
driving, adjust the seat to the proper
position so that you can easily control
the steering wheel, foot pedals and
controls on the instrument panel.
WARNING
NEVER allow children in the vehicle
unattended. The power seats are
operable when the vehicle is turned off.
NOTICE
To prevent damage to the seats:
[Always stop adjusting the seats when
the seat has moved as far forward or
rearward as possible.
[ Do not adjust the seats for longer
than necessary when the vehicle
is turned off. This may result in
unnecessary battery drain.
[ Do not operate two or more seats at
the same time. This may result in an
electrical malfunction.

Page 55 of 661

03
3-25
CAUTION
Without starting the engine, the 3rd row
seat can be folded or unfolded. When
this is attempted more than 10 times,
the battery may discharge prematurely.
Do not apply excessive force to the
3
rd row seat while in operation. It may
damage the seat.
When you operate the seat over 5 times
with no rest, the electric motor may
be overloaded. In this case, the seat
changes to overheat prevention mode.
Then you cannot operate the seat by
pressing the switch. Leave the seat for
over 1 minute for later operation.
Detection of object caught
While folding or unfolding the 3rd row
seat, when a consistent force is detected,
the seat returns to its original position or
stops operation.
However, this function may not work
when the detected resistance is below a
specific level or the seat is almost folded
or unfolded. When a strong impact is
applied to the seat, the object detection
function may be activated even if no
obstacle is present.
When any object caught is detected
multiple times while operating the seat
once, folding and unfolding are repeated
consecutively and then the operation
may stop. In this case, check that any
object is caught and then operate the
switch again to check for abnormality.
When the object detection is enabled,
the angle of the seat back may be
changed. When you operate the seat
once by pressing the folding button, the
angle of the seat back is reset.
WARNING
Do not place any part of your body
or anything in the operating area to
intentionally check the detection of any
object caught.
For safety, when folding or unfolding
the 3
rd row seat, make sure that there
is no part of body or object. To prevent
damage to the seatbelt, insert it into
its holder and store it in the retractor
inside a seat.
When the child restraint system (CRS) is
installed on the 3
rd row seat, remove the
CRS and then operate the seat.
When there is any object on the cushion
of the 3
rd row seat, remove it and then
operate the seat.
To avoid interference with a front seat,
keep the backrest of the front seat
straight and move it forward for smooth
operation.

Page 114 of 661

4
Downhill Brake Control (DBC) indicator light ........................................................4-20
AUTO STOP indicator light ........................................................................\
...............4-21
Turn signal indicator light ........................................................................\
.................4-21
High beam indicator light ........................................................................\
................4-21
Low beam indicator light ........................................................................\
.................4-21
Light ON indicator light ........................................................................\
....................4-21
High Beam Assist indicator light ........................................................................\
..... 4-22
AUTO HOLD indicator light ........................................................................\
............. 4-22
LCD Display Messages ........................................................................\
....................... 4-22 Vehicle is on ........................................................................\
..................................... 4-22
Shift to P ........................................................................\
........................................... 4-22
Vehicle is in N. Press START button and shift to P ................................................. 4-22
Low key battery (for smart key system) ................................................................. 4-22
Press brake pedal to start engine ........................................................................\
.. 4-23
Key not in vehicle (for smart key system) .............................................................. 4-23
Key not detected (for smart key system) ............................................................... 4-23
Press START button again (for smart key system) ................................................. 4-23
Press START button with digital key ...................................................................... 4-23
Check BRAKE SWITCH fuse ........................................................................\
........... 4-23
Shift to P or N to start engine ........................................................................\
.......... 4-23
Battery discharging due to external electrical devices ......................................... 4-24
Press START button with key (for smart key system) ............................................ 4-24
Place digital key on the wireless charger to keep the vehicle running ................ 4-24
Vehicle is On (started by digital key)....................................................................... 4-24
Place saved digital key on wireless charger, then press the START button ......... 4-24
Scan an authorized fingerprint, then press the START button ............................. 4-24
Digital key(s) active ........................................................................\
.......................... 4-24
Door, Hood, Liftgate open indicator ....................................................................... 4-25
Sunroof open indicator ........................................................................\
.................... 4-25
Low tire pressure ........................................................................\
............................. 4-25
Lights .................................................................\
....................................................... 4-26
Wiper ..................................................................\
......................................................4 -26
Low washer fluid ........................................................................\
.............................. 4-27
Low fuel ........................................................................\
............................................ 4-27
Low engine oil ........................................................................\
.................................. 4-27
Engine overheated ........................................................................\
........................... 4-27
Check haptic steering wheel system ..................................................................... 4-27
Check headlight ........................................................................\
............................... 4-27
Check turn signal ........................................................................\
............................. 4-27
Check headlight LED ........................................................................\
....................... 4-27

Page 121 of 661

04
4-9
Odometer
B0086EU15
B0086EU19
The odometer indicates the total
distance that the vehicle has been
driven and should be used to determine
when periodic maintenance should be
performed.
Distance to empty
B0086EU20
B0086EU21
[The distance to empty is the
estimated distance the vehicle can be
driven with the remaining fuel.
[ If the estimated distance is below
1 mi. (1 km), the trip computer will
display “---” as distance to empty.
Information
[If the vehicle is not on level ground or
the battery power has been interrupted,
the distance to empty function may not
operate correctly.
[ The distance to empty may differ
from the actual driving distance as it
is an estimate of the available driving
distance.
[ The trip computer may not register
additional fuel if less than 2.4 gallons (9
liters) of fuel are added to the vehicle.
[ The distance to empty may vary
significantly based on driving
conditions, driving habits, and
condition of the vehicle.

Page 133 of 661

04
4-21
AUTO STOP indicator light
(if equipped)
This indicator light illuminates:
[[Whit
e] When the system operating
conditions are satisfied.
[ [Green] When the ISG system is
activated.
[ [Yellow] Whenever there is a
malfunction with the ISG function.
If this occurs, have the vehicle inspected
by an authorized HYUNDAI dealer as
soon as possible.
For more details, refer to "ISG (Idle Stop
and Go) system" section in chapter 6.
Information
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, EPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean the
system has malfunctioned.
Turn signal indicator light
This indicator light blinks:
When you operate the turn signal
indica
tor stalk.
If any of the following occur, there may
be a malfunction with the turn signal
system.
- The turn signal indicator light
illuminates but does not blink

- The turn signal indicator light blinks
rapidly

- The turn signal indicator light does not
illuminate at all
If this occurs, have the vehicle inspected
by an authorized HYUNDAI dealer as
soon as possible.
High beam indicator light
This indicator light illuminates:
[ When the headligh
ts are on and in the
high beam position
[ When the turn signal lever is pulled
into the Flash-to-Pass position.
Low beam indicator light
This indicator light illuminates:
When the headlights are on.
Light ON indicator light
This indicator light illuminates:
When the position lamps or headlights
ar

e on.

Page 134 of 661

Instrument Cluster4-22
High Beam Assist indicator
light
This indicator light illuminates:
When the high-beam is on with the light
s
witch in the AUTO position.
[ White: When High Beam Assist is
ready to operate.
[ Green: When High Beam Assist is
operating.
If your vehicle detects oncoming or
preceding vehicles, High Beam Assist
will switch the high beam to low beam
automatically.
For more details, refer to “High Beam
Assist (HBA)” section in chapter 5.
AUTO HOLD indicator light
This indicator light illuminates:
[ [Whit
e] When you activate Auto Hold
by pressing the AUTO HOLD switch.
[ [Green] When you stop the vehicle
completely by depressing the brake
pedal with Auto Hold activated.
[ [Yellow] Whenever there is a
malfunction with the Auto Hold
function.
If this occurs, have the vehicle
inspected by an authorized HYUNDAI
dealer as soon as possible.
For more details, refer to “Electronic
Parking Brake (EPB)” section in chapter
6.
LCD Display Messages
Vehicle is on
This message is displayed if you open
the driver’s door when the gear is in P
(Park) and the ignition switch in the ON
or START position.
Turn the engine off before leaving the
vehicle.
Shift to P
This message is displayed if you try to
turn off the vehicle without the gear in
the P (Park) position.
If this occurs, the ignition switch places
to the ACC position.
Vehicle is in N. Press START button
and shift to P (if equipped)
This message is displayed if you try to
turn off the vehicle with the gear in N
(Neutral).
To turn off the vehicle:
1. Press the Engine Start/Stop button. The button will change to the ON
position.
2. Press the P button to shift to P (Park).
3. Press the Engine Start/Stop button again, then the vehicle will turn off.
Low key battery (for smart key
system)
This message is displayed if the battery
of the smart key is discharged while
changing the ignition switch to the OFF
position.

Page 136 of 661

Instrument Cluster4-24
Battery discharging due to external
electrical devices (if equipped)
This message is displayed if the battery
voltage is weak due to any non-factory
electrical accessories (ex. dashboard
camera) while parking. Be careful that
the battery is not discharged.
If the warning message appears after
removing the non-factory electrical
accessories, have the vehicle inspected
by an authorized HYUNDAI dealer.
Press START button with key
(for smart key system)
This warning message is displayed if you
press the Engine Start/Stop button while
the warning message "Key not detected"
is displayed.
At this time, the immobilizer indicator
light blinks.
Place digital key on the wireless
charger to keep the vehicle running
If the vehicle is remotely started and
‘Start Vehicle’ is deselected from the
Settings menu in the infotainment
system screen for Driver 1 and Driver 2,
this message will be displayed for up to
30 seconds when a door is opened after
unlocking the doors with a digital key.
To drive your vehicle, place the
registered digital key on the wireless
charger, when this message appears.
Vehicle is On (started by digital key)
This message is displayed for up to 10
seconds if the driver's door is opened
without the driver's seat belt fastened
after turning on the engine with a digital
key. After the message is displayed, a
warning sounds when the door is closed.
Information
Since the engine was started with a digital
key, if the engine is turned off, and there is
no smart key or digital key in the vehicle,
it may be difficult to start the engine
again.
Place saved digital key on wireless
charger, then press the START
button
This message is displayed for 6 seconds
and the immobilizer indicator light
(
) will blink for 10 seconds after the
message “Press START button with key”
is displayed for 4 seconds if the smart
key is not in the vehicle or not detected,
or the digital key is not placed on the
wireless charger when you press the
Engine Start/Stop button. To start the
vehicle, place a registered digital key on
the wireless charger, and then press the
Engine Start/Stop button.
Scan an authorized fingerprint, then
press the START button
This message is displayed for 6 seconds
and the immobilizer indicator light
(
) will blink for 10 seconds after the
message “Press START button with key”
is displayed for 4 seconds if the smart
key is not in the vehicle or not detected,
or your fingerprint is not verified when
you press the Engine Start/Stop button.
To start the vehicle, have an authorized
fingerprint verified on the fingerprint
sensor, and then press the Engine Start/
Stop button.
Digital key(s) active
This message is displayed for 4 seconds
when a smartphone key or NFC card
key is registered, and vehicle doors are
locked and unlocked after more than
10 minutes and the ignition switch is
placed to the ON position. The message
is not displayed again until more than 10
minutes have passed after the doors are
relocked.

Page:   1-10 11-20 21-30 31-40 41-50 ... 80 next >