Timing INFINITI FX35 2004 User Guide

BRC-36
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
ON and OFF Timing for ABS Warning Lamp, VDC OFF Indicator Lamp, SLIP Indicator Lamp,
Brake Warning Lamp
×: ON –: OFF
NOTE:
1. Brake warning lamp will turn on in case of operating parking brake (switch turned on) or of actuating brake
fluid level switch (brake fluid is insufficient).
2. After starting engine, turn OFF.
Basic InspectionAFS001SS
BASIC INSPECTION 1: BRAKE FLUID AMOUNT, LEAKS, AND BRAKE PADS INSPECTION
1. Check fluid level in the brake reservoir tank. If fluid level is low, refill brake fluid.
2. Check brake piping and around ABS actuator and electric unit (control unit) for leaks. If there is leaking or
oozing fluid, check the following items.

If ABS actuator and electric unit (control unit) connection is loose, tighten piping to the specified torque
and re-perform the leak inspection to make sure there are no leaks.

If there is damage to the connection flare nut or ABS actuator and electric unit (control unit) screw,
replace the damaged part and re-perform the leak inspection to make sure there are no leaks.

When there is fluid leaking or oozing from a part other than ABS actuator and electric unit (control unit)
connection, if fluid is just oozing out, use a clean cloth to wipe off the oozing fluid and re-check for
leaks. If fluid is still oozing out, replace the damaged part.

When there is fluid leaking or oozing at ABS actuator and electric unit (control unit), if fluid is just oozing
out, use a clean cloth to wipe off oozing fluid and re-check for leaks. If fluid is still oozing out, replace
ABS actuator and electric unit (control unit) body.
CAUTION:
ABS actuator and electric unit (control unit) body cannot be disassembled.
3. Check brake pad degree of wear. Refer to BR-20, "
PAD WEAR INSPECTION" in “Front Disc Brake” and
BR-25, "
PAD WEAR INSPECTION" in “Rear Disc Brake”
BASIC INSPECTION 2: POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPEC-
TION
Make sure battery positive cable, negative cable and ground connection are not loose. If looseness is
detected, tighten the cables. In addition, check the battery voltage to make sure it has not dropped and alter-
nator is normal.
ConditionABS warning
lampVDC OFF indi-
cator lampSLIP indicator
lampBrake warning
lamp [Note 1]Remarks
Ignition SW OFF. – – – — —
Approx. 2 seconds after igni-
tion switch is turned ON.×××× [Note 2] —
Approx. 2 seconds later after
ignition switch ON.–––× [Note 2]Go out 2 seconds after
ignition switch is turned
ON.
VDC OFF SW is turned ON.
(VDC/TCS function is OFF.)–×–— —
VDC/TCS/ABS error.×××—There is an ABS actua-
tor and electric unit
(control unit) error.
(Power, ground or sys-
tem malfunction)
When VDC/TCS is not func-
tioning normally.–××——
EBD error.××××—

CO-8
[VQ35DE]
OVERHEATING CAUSE ANALYSIS
Revision: 2004 November 2004 FX35/FX45
Except cool-
ing system
parts mal-
function— Overload on engineAbusive drivingHigh engine rpm under no
load
Driving in low gear for
extended time
Driving at extremely high
speed
Powertrain system mal-
function
— Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flowBlocked bumper —
— Blocked radiator grilleInstalled car brassiere
Mud contamination or
paper clogging
Blocked radiator —
Blocked condenser
Blocked air flow
Installed large fog lamp Symptom Check items

WATER PUMP
CO-23
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
7. Remove timing chain tensioner (primary) with the following pro-
cedure.
a. Pull the lever down and release plunger stopper tab.

Plunger stopper tab can be pushed up to release (coaxial
structure with lever).
b. Insert stopper pin into the tensioner body hole to hold lever and
keep the plunger stopper tab released.
NOTE:
An Allen wrench [2.5 mm (0.098 in)] is used for a stopper pin as
an example.
c. Insert plunger into the tensioner body by pressing timing chain
slack guide.
d. Keep slack guide pressed and hold plunger in by pushing stopper pin deeper through lever and into the
tensioner body hole.
e. Turn crankshaft pulley approximately 20° clockwise so that tim-
ing chain on the timing chain tensioner (primary) side is loose.
f. Remove mounting bolts and timing chain tensioner (primary).
CAUTION:
Be careful not to drop mounting bolts inside chain case.
8. Remove three water pump fixing bolts. Secure a gap between
water pump gear and timing chain, by turning crankshaft pulley
counterclockwise until timing chain looseness on water pump
sprocket becomes maximum.
PBIC2112E
PBIC0848E
PBIC2113E
PBIC1193E

CO-24
[VQ35DE]
WATER PUMP
Revision: 2004 November 2004 FX35/FX45
9. Screw M8 bolts [pitch: 1.25 mm (0.049 in) length: approx. 50
mm (1.97 in)] into water pumps upper and lower mounting bolt
holes until they reach timing chain case. Then, alternately
tighten each bolt for a half turn, and pull out water pump.
CAUTION:

Pull straight out while preventing vane from contacting
socket in installation area.

Remove water pump without causing sprocket to contact
timing chain.
10. Remove M8 bolts and O-rings from water pump.
CAUTION:
Do not disassembly water pump.
INSPECTION AFTER REMOVAL

Check for badly rusted or corroded water pump body assembly.

Check for rough operation due to excessive end play.

If anything is found, replace water pump.
INSTALLATION
1. Install new O-rings to water pump.

Apply engine oil and engine coolant to O-rings as shown in
the figure.

Locate O-ring with white paint mark to engine front side.
2. Install water pump.
CAUTION:
Do not allow cylinder block to nip O-rings when install
water pump.

Make sure timing chain and water pump sprocket are
engaged.

Insert water pump by tightening mounting bolts alternately
and evenly.
3. Install timing chain tensioner (primary) as the following:
a. Remove dust and foreign material completely from backside of chain tensioner and from installation area
of rear timing chain case.
b. Turn crankshaft pulley clockwise so that timing chain on the timing chain tensioner (primary) side is loose.

Apply engine oil should be applied to the oil hole and tensioner, when installing timing chain
tensioner.
JLC357B
SLC943A
PBIC1397E
PBIC1058E

WATER PUMP
CO-25
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
c. Install timing chain tensioner (primary).
d. Remove stopper pin.
4. Install chain tensioner cover and water pump cover.
a. Before installing, remove all traces of liquid gasket from mating
surface of water pump cover and chain tensioner cover using a
scraper. Also remove traces of liquid gasket from the mating sur-
face of front timing chain case.
b. Apply a continuous bead of liquid gasket to mating surface of
chain tensioner cover and water pump cover with tube presser
[SST: WS39930000 ( – )].
Use Genuine RTV Silicone Sealant or equivalent. GI-48,
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS".
5. Install water drain plug (front) of cylinder block.

Apply liquid gasket to the thread of water drain plug (front).
Use Genuine RTV Silicone Sealant or equivalent. Refer to GI-48, "
RECOMMENDED CHEMICAL
PRODUCTS AND SEALANTS".
6. Install in the reverse order of removal for remaining parts.

After starting engine, let idle for three minutes, then rev engine up to 3,000 rpm under no load to
purge air from the high-pressure chamber of chain tensioner. Engine may produce a rattling
noise. This indicates that air still remains in the chamber and is not a matter of concern.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant using radiator cap tester adapter [SST: EG17650301 (J-33984-A)] and
radiator cap tester (commercial service tool). Refer to CO-11, "
CHECKING COOLING SYSTEM FOR
LEAKS" .

Start and warm up engine. Visually make sure that there is no leaks of engine coolant and A/T fluid.
SLC448B
SLC446B
PBIC1283E

OVERHEATING CAUSE ANALYSIS
CO-33
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
Except cool-
ing system
parts mal-
function— Overload on engineAbusive drivingHigh engine rpm under no
load
Driving in low gear for
extended time
Driving at extremely high
speed
Powertrain system mal-
function
— Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flowBlocked bumper —
— Blocked radiator grilleInstalled car brassiere
Mud contamination or
paper clogging
Blocked radiator —
Blocked condenser
Blocked air flow
Installed large fog lamp Symptom Check items

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: 2004 November 2004 FX35/FX45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
Alphabetical Index .................................................. 15
DTC No. Index ....................................................... 19
PRECAUTIONS ........................................................ 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 23
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 23
Precaution .............................................................. 23
Wiring Diagrams and Trouble Diagnosis ................ 26
PREPARATION ......................................................... 27
Special Service Tools ............................................. 27
Commercial Service Tools ...................................... 28
ENGINE CONTROL SYSTEM .................................. 29
System Diagram ..................................................... 29
Vacuum Hose Drawing ........................................... 30
System Chart ......................................................... 31
Multiport Fuel Injection (MFI) System .................... 32
Electronic Ignition (EI) System ............................... 34
Air Conditioning Cut Control ................................... 35
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 35
CAN communication .............................................. 36
BASIC SERVICE PROCEDURE .............................. 37
Idle Speed and Ignition Timing Check .................... 37
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................. 38
Accelerator Pedal Released Position Learning ...... 49
Throttle Valve Closed Position Learning ................ 49
Idle Air Volume Learning ........................................ 49
Fuel Pressure Check .............................................. 51
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 53
Introduction ............................................................ 53
Two Trip Detection Logic ........................................ 53
Emission-Related Diagnostic Information .............. 54
IVIS (Infiniti Vehicle Immobilizer System — NATS) ... 68
Malfunction Indicator Lamp (MIL) ........................... 68
OBD System Operation Chart ................................ 72TROUBLE DIAGNOSIS ............................................ 77
Trouble Diagnosis Introduction ............................... 77
DTC Inspection Priority Chart ................................. 80
Fail-Safe Chart ....................................................... 82
Basic Inspection ..................................................... 83
Symptom Matrix Chart ............................................ 88
Engine Control Component Parts Location ............ 92
Circuit Diagram ....................................................... 98
ECM Harness Connector Terminal Layout ...........100
ECM Terminals and Reference Value ...................100
CONSULT-II Function ...........................................109
Generic Scan Tool (GST) Function .......................122
CONSULT-II Reference Value in Data Monitor .....125
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................129
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .131
Description ............................................................131
Testing Condition ..................................................131
Inspection Procedure ............................................131
Diagnostic Procedure ...........................................132
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................135
Description ............................................................135
Diagnostic Procedure ...........................................135
POWER SUPPLY AND GROUND CIRCUIT ...........136
Wiring Diagram .....................................................136
Diagnostic Procedure ...........................................137
Ground Inspection ................................................141
DTC U1000, U1001 CAN COMMUNICATION LINE .142
Description ............................................................142
On Board Diagnosis Logic ....................................142
DTC Confirmation Procedure ...............................142
Wiring Diagram .....................................................143
Diagnostic Procedure ...........................................144
DTC P0011, P0021 IVT CONTROL ........................145
Description ............................................................145
CONSULT-II Reference Value in Data Monitor Mode
.145
On Board Diagnosis Logic ....................................146

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45Component Inspection ......................................... 575
Removal and Installation ...................................... 575
DTC P2138 APP SENSOR ..................................... 576
Component Description ........................................ 576
CONSULT-II Reference Value in Data Monitor Mode
. 576
On Board Diagnosis Logic ................................... 576
DTC Confirmation Procedure ............................... 577
Wiring Diagram .................................................... 578
Diagnostic Procedure ........................................... 579
Component Inspection ......................................... 584
Removal and Installation ...................................... 584
IGNITION SIGNAL .................................................. 585
Component Description ........................................ 585
Wiring Diagram .................................................... 586
Diagnostic Procedure ........................................... 591
Component Inspection ......................................... 595
Removal and Installation ...................................... 596
INJECTOR CIRCUIT ............................................... 597
Component Description ........................................ 597
CONSULT-II Reference Value in Data Monitor Mode
. 597
Wiring Diagram .................................................... 598
Diagnostic Procedure ........................................... 599
Component Inspection ......................................... 602
Removal and Installation ...................................... 602
FUEL PUMP CIRCUIT ............................................ 603
Description ........................................................... 603
CONSULT-II Reference Value in Data Monitor Mode
. 603
Wiring Diagram .................................................... 604
Diagnostic Procedure ........................................... 605
Component Inspection ......................................... 608
Removal and Installation ...................................... 608
REFRIGERANT PRESSURE SENSOR ................. 609
Component Description ........................................ 609
Wiring Diagram .................................................... 610
Diagnostic Procedure ............................................ 611
Removal and Installation ...................................... 613
ELECTRICAL LOAD SIGNAL ................................ 614
Description ........................................................... 614
CONSULT-II Reference Value in Data Monitor Mode
. 614
Diagnostic Procedure ........................................... 614
ICC BRAKE SWITCH ............................................. 615
Component Description ........................................ 615
CONSULT-II Reference Value in Data Monitor Mode
. 615
Wiring Diagram .................................................... 616
Diagnostic Procedure ........................................... 617
Component Inspection ......................................... 622
ASCD BRAKE SWITCH ......................................... 624
Component Description ........................................ 624
CONSULT-II Reference Value in Data Monitor Mode
. 624
Wiring Diagram .................................................... 625
Diagnostic Procedure ........................................... 626
Component Inspection ......................................... 631ASCD INDICATOR ..................................................632
Component Description ........................................632
CONSULT-II Reference Value in Data Monitor Mode
.632
Wiring Diagram .....................................................633
Diagnostic Procedure ...........................................634
SNOW MODE SWITCH ..........................................635
Description ............................................................635
CONSULT-II Reference Value in the Data Monitor
Mode .....................................................................635
Wiring Diagram .....................................................636
Diagnostic Procedure ...........................................637
Component Inspection ..........................................640
MIL AND DATA LINK CONNECTOR ......................641
Wiring Diagram .....................................................641
EVAPORATIVE EMISSION SYSTEM .....................643
Description ............................................................643
Component Inspection ..........................................646
Removal and Installation ......................................647
How to Detect Fuel Vapor Leakage ......................647
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ....................................................................650
System Description ...............................................650
Diagnostic Procedure ...........................................651
Component Inspection ..........................................653
POSITIVE CRANKCASE VENTILATION ...............655
Description ............................................................655
Component Inspection ..........................................655
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .657
System Description ...............................................657
Component Description ........................................659
SERVICE DATA AND SPECIFICATIONS (SDS) ....660
Fuel Pressure .......................................................660
Idle Speed and Ignition Timing .............................660
Calculated Load Value ..........................................660
Mass Air Flow Sensor ...........................................660
Intake Air Temperature Sensor .............................660
Engine Coolant Temperature Sensor ...................660
Heated Oxygen Sensor 1 Heater .........................660
Heated Oxygen sensor 2 Heater ..........................660
Crankshaft Position Sensor (POS) .......................660
Camshaft Position Sensor (PHASE) ....................660
Throttle Control Motor ...........................................660
Injector ..................................................................661
Fuel Pump ............................................................661
VK45DE
INDEX FOR DTC .....................................................662
Alphabetical Index ................................................662
DTC No. Index ......................................................665
PRECAUTIONS ......................................................670
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................670
On Board Diagnostic (OBD) System of Engine and
A/T ........................................................................670
Precaution ............................................................670
Wiring Diagrams and Trouble Diagnosis ..............673

EC-8Revision: 2004 November 2004 FX35/FX45 PREPARATION .......................................................674
Special Service Tools ...........................................674
Commercial Service Tools ....................................675
ENGINE CONTROL SYSTEM ................................676
System Diagram ...................................................676
Vacuum Hose Drawing .........................................677
System Chart ........................................................678
Multiport Fuel Injection (MFI) System ...................679
Electronic Ignition (EI) System .............................681
Nissan Torque Demand (NTD) Control System ....682
Air Conditioning Cut Control .................................683
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................683
CAN communication .............................................684
BASIC SERVICE PROCEDURE .............................685
Idle Speed and Ignition Timing Check ..................685
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................687
Accelerator Pedal Released Position Learning ....698
Throttle Valve Closed Position Learning ...............698
Idle Air Volume Learning ......................................698
Fuel Pressure Check ............................................700
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........703
Introduction ...........................................................703
Two Trip Detection Logic ......................................703
Emission-related Diagnostic Information ..............704
IVIS (Infiniti Vehicle Immobilizer System — NATS) .717
Malfunction Indicator Lamp (MIL) .........................717
OBD System Operation Chart ..............................721
TROUBLE DIAGNOSIS ..........................................726
Trouble Diagnosis Introduction .............................726
DTC Inspection Priority Chart ...............................729
Fail-safe Chart ......................................................731
Basic Inspection ...................................................733
Symptom Matrix Chart ..........................................738
Engine Control Component Parts Location ..........742
Circuit Diagram .....................................................748
ECM Harness Connector Terminal Layout ...........750
ECM Terminals and Reference Value ...................750
CONSULT-II Function ...........................................759
Generic Scan Tool (GST) Function .......................772
CONSULT-II Reference Value in Data Monitor .....775
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................778
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .780
Description ............................................................780
Testing Condition ..................................................780
Inspection Procedure ............................................780
Diagnostic Procedure ...........................................781
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................784
Description ............................................................784
Diagnostic Procedure ...........................................784
POWER SUPPLY AND GROUND CIRCUIT ...........785
Wiring Diagram .....................................................785
Diagnostic Procedure ...........................................786
Ground Inspection ................................................791
DTC U1000, U1001 CAN COMMUNICATION LINE .792
Description ............................................................792On Board Diagnosis Logic ....................................792
DTC Confirmation Procedure ................................792
Wiring Diagram .....................................................793
Diagnostic Procedure ............................................794
DTC P0011, P0021 IVT CONTROL .........................795
Description ............................................................795
CONSULT-II Reference Value in Data Monitor Mode
.796
On Board Diagnosis Logic ....................................796
DTC Confirmation Procedure ................................797
Wiring Diagram .....................................................798
Diagnostic Procedure ............................................801
Component Inspection ..........................................805
Removal and Installation .......................................805
DTC P0031, P0032, P0051, P0052 HO2S1 HEATER .806
Description ............................................................806
CONSULT-II Reference Value in Data Monitor Mode
.806
On Board Diagnosis Logic ....................................806
DTC Confirmation Procedure ................................807
Wiring Diagram .....................................................808
Diagnostic Procedure ............................................811
Component Inspection ..........................................813
Removal and Installation .......................................813
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .814
Description ............................................................814
CONSULT-II Reference Value in Data Monitor Mode
.814
On Board Diagnosis Logic ....................................814
DTC Confirmation Procedure ................................815
Wiring Diagram .....................................................816
Diagnostic Procedure ............................................819
Component Inspection ..........................................821
Removal and Installation .......................................821
DTC P0101 MAF SENSOR .....................................822
Component Description ........................................822
CONSULT-II Reference Value in Data Monitor Mode
.822
On Board Diagnosis Logic ....................................822
DTC Confirmation Procedure ................................823
Overall Function Check .........................................824
Wiring Diagram .....................................................825
Diagnostic Procedure ............................................826
Component Inspection ..........................................829
Removal and Installation .......................................829
DTC P0102, P0103 MAF SENSOR .........................830
Component Description ........................................830
CONSULT-II Reference Value in Data Monitor Mode
.830
On Board Diagnosis Logic ....................................830
DTC Confirmation Procedure ................................831
Wiring Diagram .....................................................832
Diagnostic Procedure ............................................833
Component Inspection ..........................................836
Removal and Installation .......................................836
DTC P0112, P0113 IAT SENSOR ............................837
Component Description ........................................837
On Board Diagnosis Logic ....................................837
DTC Confirmation Procedure ................................837

EC-14Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value in Data Monitor Mode
1255
Wiring Diagram ....................................................1256
Diagnostic Procedure ..........................................1257
Component Inspection .........................................1260
Removal and Installation .....................................1261
IGNITION SIGNAL .................................................1262
Component Description .......................................1262
Wiring Diagram ....................................................1263
Diagnostic Procedure ..........................................1268
Component Inspection .........................................1272
Removal and Installation .....................................1273
INJECTOR CIRCUIT ..............................................1274
Component Description .......................................1274
CONSULT-II Reference Value in Data Monitor Mode
1274
Wiring Diagram ....................................................1275
Diagnostic Procedure ..........................................1276
Component Inspection .........................................1279
Removal and Installation .....................................1279
FUEL PUMP CIRCUIT ...........................................1280
Description ...........................................................1280
CONSULT-II Reference Value in Data Monitor Mode
1280
Wiring Diagram ....................................................1281
Diagnostic Procedure ..........................................1282
Component Inspection .........................................1285
Removal and Installation .....................................1286
REFRIGERANT PRESSURE SENSOR .................1287
Component Description .......................................1287
Wiring Diagram ....................................................1288
Diagnostic Procedure ..........................................1289
Removal and Installation .....................................1291
ELECTRICAL LOAD SIGNAL ...............................1292
Description ...........................................................1292
CONSULT-II Reference Value in Data Monitor Mode
1292
Diagnostic Procedure ..........................................1292
ICC BRAKE SWITCH .............................................1293
Component Description .......................................1293
CONSULT-II Reference Value in Data Monitor Mode
1293
Wiring Diagram ....................................................1294
Diagnostic Procedure ..........................................1295
Component Inspection .........................................1301
ASCD BRAKE SWITCH .........................................1302
Component Description .......................................1302
CONSULT-II Reference Value in Data Monitor Mode
1302Wiring Diagram ....................................................1303
Diagnostic Procedure ...........................................1304
Component Inspection .........................................1308
ASCD INDICATOR .................................................1309
Component Description .......................................1309
CONSULT-II Reference Value in Data Monitor Mode
1309
Wiring Diagram ....................................................1310
Diagnostic Procedure ...........................................1311
SNOW MODE SWITCH ..........................................1312
Description ...........................................................1312
CONSULT-II Reference Value in the Data Monitor
Mode ....................................................................1312
Wiring Diagram ....................................................1313
Diagnostic Procedure ...........................................1314
Component Inspection .........................................1317
MIL AND DATA LINK CONNECTOR .....................1318
Wiring Diagram ....................................................1318
EVAPORATIVE EMISSION SYSTEM ....................1320
Description ...........................................................1320
Component Inspection .........................................1323
Removal and Installation ......................................1324
How to Detect Fuel Vapor Leakage .....................1324
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................1327
System Description ..............................................1327
Diagnostic Procedure ...........................................1328
Component Inspection .........................................1330
POSITIVE CRANKCASE VENTILATION ...............1332
Description ...........................................................1332
Component Inspection .........................................1332
AUTOMATIC SPEED CONTROL DEVICE (ASCD) 1334
System Description ..............................................1334
Component Description .......................................1335
SERVICE DATA AND SPECIFICATIONS (SDS) ...1336
Fuel Pressure .......................................................1336
Idle Speed and Ignition Timing .............................1336
Calculated Load Value .........................................1336
Mass Air Flow Sensor ..........................................1336
Intake Air Temperature Sensor ............................1336
Engine Coolant Temperature Sensor ...................1336
Heated Oxygen Sensor 1 Heater .........................1336
Heated Oxygen Sensor 2 Heater .........................1336
Crankshaft Position Sensor (POS) ......................1336
Camshaft Position Sensor (PHASE) ....................1336
Throttle Control Motor ..........................................1336
Injector .................................................................1337
Fuel Pump ............................................................1337