lighting system INFINITI FX35 2004 User Guide

NAVIGATION SYSTEM
AV-151
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector and combination unified meter and A/C amp. connector.
3. Check continuity between display control unit harness connector
M75 terminal 16 (R/G) and unified meter and A/C amp. harness
connector M56 terminal 26 (R/G).
4. Check continuity between display control unit harness connector
M75 terminal 16 (R/G) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VEHICLE SPEED SIGNAL
1. Connect unified meter and A/C amp. connector.
2. Start the engine.
3. Drive vehicle at a constant speed.
4. Check signal between display control unit harness connector
M75 terminal 16 (R/G) and ground with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> INSPECTION END
NG >> Check unified meter and A/C amp. system. Refer to DI-
17, "Vehicle Speed Signal Inspection" .
Illumination Signal Check for NAVI Control UnitAKS00BND
1. CHECK ILLUMINATION SIGNAL
1. Check voltage between NAVI control unit harness connector ter-
minals and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.16 – 26 : Continuity should exist.
16 – Ground : Continuity should not exist.
PKIA2864E
16 – Ground : Refer to AV- 1 2 3 , "Terminals
and Reference Value for Display
Control Unit" .
PKIA2866E
Terminals
Condition Voltage (+)
(–)
ConnectorTerminal
(Wire color)
B207 25 (R) GroundLighting switch is ON Approx. 12V
Lighting switch is OFF Approx. 0V
SKIB0315E

AV-152
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
Illumination Signal Check for Display Control Unit AKS00BNE
1. CHECK ILLUMINATION SIGNAL
1. Check voltage between display control unit harness connector
terminals and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Ignition Signal Check for NAVI Control UnitAKS00BNF
1. CHECK IGNITION SIGNAL
1. Turn ignition switch ON.
2. Check voltage between NAVI control unit harness connector
B207 terminal 26 (G) and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Ignition Signal Check for Display Control UnitAKS00BNG
1. CHECK IGNITION SIGNAL
1. Turn ignition switch ON.
2. Check voltage between display control unit harness connector
M75 terminal 12 (G/R) and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Reverse Signal Check for NAVI Control UnitAKS00BNH
1. CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Selector lever into R-position.
Does
“R” in the shift position indicator come on?
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT- 1 2 5 , "
BACK-UP LAMP" .
Terminals
Condition Voltage (+)
(–)
ConnectorTe r m i n a l
(Wire color)
M75 14 (R/L) GroundLighting switch is ON Approx. 12V
Lighting switch IS OFF Approx. 0V
SKIB0445E
26 – Ground : Battery voltage
SKIA8939E
12 – Ground : Battery voltage
SKIA8940E

NAVIGATION SYSTEM
AV-173
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
in the unit, display the track of the vehicle on the map screen and compare it with the actual road configu-
ration.

Sample tests
–<To determine if the current-location mark skips at the same position, if so, whether it is caused by map-
matching or by GPS>
Perform test pattern 1.
–<To determine if the pattern of streets displayed is correct or not>;
Perform test pattern 1 & 2.
Compare the track of the vehicle on the map screen and the actual road configuration. For fairly accurate
tracking, plotting shall be made every several hundred meters.
–<When the distance is adjusted accurately>;
Perform test pattern 1 & 2.
Drive on a road of which distance is accurately known (by utilizing distance posts on a highway). Calculate
the rate of change (increased/decreased) of the distance by comparing with the actual distance.
Correction = 1 – A/B
A: Distance shown on the screen
B: Actual distance
YES or NO
YES >>
If adjustment is insufficient, perform adjustment again.

If any error is found in the map, please let us know.

Replace NAVI control unit.
NO >> Limit of the location detection capacity of the navigation system.
Example of Symptoms Judged Not MalfunctionAKS007KH
BASIC OPERATION
VEHICLE MARK
Symptom Cause Remedy
No image is shown. Display brightness adjustment is set fully to
DARK side.Adjust the display brightness.
No guide sound is heard.
Audio guide volume is too low or
too high.Volume control is set to OFF, MIN or MAX. Adjust the audio guide volume.
Audio guidance is not available while the vehicle
is driving on a dark pink route.System is not malfunction.
Screen is too dark.
Motion of the image is too slow.Temperature inside the vehicle is low. Wait until the temperature inside the vehicle
reaches the proper temperature.
Small black or bright spots appear
on the screen.Symptom peculiar to a liquid crystal display. System is not malfunction.
Symptom Cause Remedy
Map screen and BIRDVIEW™
Name of the place vary with the
screen.Some thinning of the character data is done to
prevent the display becoming to complex. In
some cases and in some locations, the display
contents may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing.System is not malfunction.
Vehicle mark is not positioned cor-
rectly.Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF.Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON.The daytime screen is selected by the “SWITCH
SCREENS” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screen may
be inhibited by the automatic illumination adjust-
ment function.Perform screen dimming and select the
nighttime screen by “SWITCH SCREENS”.
Map screen will not scroll in accor-
dance with the vehicle travel.Current location is not displayed. Press “MAP” button to display the current
location.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP” button to display the current
location.

AV-188
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for DVD PlayerAKS00BOX
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference valueExample of symp-
tom
(+) (-)Ignition
switchOperation
1 (L) 2 (R)MES output
signal (LH)
Output ACCRear AV
switch is ONNo sound
from speaker LH
3 (LG) 4 (PU)MES output
signal (RH)No sound
from speaker RH
8–Shield – – – – –
9
(Y/B)GroundAudio ON
signal (MES -
H/U) Output ACCPush “POWER”
switch of DVD
playerApprox. 5VSystem dose not
work properly
10
(R/Y)GroundIllumination
control signalInput OFFIllumination con-
trol switch is oper-
ated by lighting
switch in 1st posi-
tion.Changes between approx. 0 and
approx. 12V.DVD player illumi-
nation does not
come on then light-
ing switch is ON
11
(L/W)GroundControl sig-
nal (H/U -
MES)Input ACCPush “POWER”
switch of DVD
playerApprox. 5VSystem dose not
work properly
12
(R/L)GroundIllumination
signalInput OFFLighting switch is
ON (1st position).Approx. 12VDVD player illumi-
nation dose not
come on then light-
ing switch is ON Lighting switch
OFF.Approx. 0V
15
(LG/R)GroundACC power
supplyInput ACC – Battery voltageSystem does not
work properly
16
(W/L)GroundBattery
power supplyInput OFF – Battery voltageSystem dose not
work properly
17 (G) 19 (LG)MES output
signal (Com-
mon)Output ACCPlay CD or DVD
videoApprox. 0V –
18 (L) 19 (LG)MES output
signal (L+)Output ACCPlay CD or DVD
videoNo sound from
head phone LH
19 (LG) Ground Ground – ON – Approx. 0V –
20 (Y) 19 (LG)MES output
signal (R+)Output ACCPlay CD or DVD
videoNo sound from
head phone RH
21 (L) GroundACC power
supplyOutput ACC – Approx. 5VDisplay does not
work properly
22 (B) Ground Ground – ON – Approx. 0V –
SKIA0177E
SKIA5828E
SKIA5828E

BCS-4
BCM (BODY CONTROL MODULE)
Revision: 2004 November 2004 FX35/FX45

BCM reads operation status of combination switch using combinations shown in table below.
NOTE:
Headlamp has a dual system switch.
4. Sample operation: (When lighting switch 1st position turned ON)

When lighting switch 1st position is turned ON, contact in combination switch turns ON. At this time if
OUTPUT 4 transistor is activated, BCM detects that voltage changes in INPUT 5.

When OUTPUT 4 transistor is ON, BCM detects that voltage changes in INPUT 5, and judges that light-
ing switch 1st position is ON. Then BCM sends tail lamp ON signal to IPDM E/R using CAN communi-
cation.

When OUTPUT 4 transistor is activated again, BCM detects that voltage changes in INPUT 5, and rec-
ognizes that lighting switch 1st position is continuously ON.
SKIA4959E
SKIA4960E

BL-64
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for BCMAIS004MF
*1 : In the state that hazard reminder operates.
*2 : In the state that room lamp switch is in “DOOR” position.TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
Approx.
1PUKey ring illumination output sig-
nal Key ring illumination is lighting. Battery voltage
Key ring illumination is being turned off. 0
11 LG/R Ignition switch Ignition switch is in ACC or ON position Battery voltage
12 P/BFront door switch (Passenger
side)ON (door open) → OFF (door closed) 0 → Battery voltage
13 P/L Rear door switch RH ON (door open) → OFF (door closed) 0 → Battery voltage
37 B/W Key switchON (Key is inserted in IGN key cylinder)
→ OFF (Key is removed from IGN key
cylinder)Battery voltage → 0
38 W/L Ignition switchIgnition switch is in ON or START posi-
tionBattery voltage
39 L CAN H — —
40 R CAN L — —
41 R/B Battery saver output signal30 minutes after ignition switch is turned
to OFF0
Ignition switch is in ON position Battery voltage
42 L/R Battery power supply (fuse) — Battery voltage
44 YDriver door lock actuator
(Unlock)Door lock / unlock switch
(Free → Unlock)0 → Battery voltage
45 G/W Left turn signal lampWhen door lock or unlock is operated
using key fob.*
1
(ON → OFF)Battery voltage → 0
46 BR/W Right turn signal lampWhen door lock or unlock is operated
using key fob.*
1
(ON → OFF)Battery voltage → 0
47 Y/R Step lamp output signalStep lamp is lighting. 0
Step lamp is being turned off. Battery voltage
48 PU/W Room lamp output signalRoom lamp is lighting.*
20
Room lamp is being turned off.*
2Battery voltage
49, 52 B Ground — 0
50 PU Door lock actuator (Lock)Door lock / unlock switch
(Free → Lock)0 → Battery voltage
51 W/BPassenger and rear doors lock
actuator (Unlock)Door lock / unlock switch
(Free → Unlock)0 → Battery voltage
54 WBattery power supply
(power window)—Battery voltage
55 GBattery power supply (Fusible
link)—Battery voltage
58 L Back door switch OFF (Door close) → ON (Door open) 9 → 0
62 W Front door switch (Driver side) OFF (Door close) → ON (Door open) Battery voltage → 0
63 P Rear door switch LH OFF (Door close) → ON (Door open) Battery voltage → 0

REMOTE KEYLESS ENTRY SYSTEM
BL-79
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
Check Hazard FunctionAIS004MP
1. CHECK HAZARD WARNING LAMP
Do hazard warning lamp flash with hazard switch?
YES or NO
YES >> Hazard warning lamp circuit is OK.
NO >> Check hazard circuit. Refer to LT- 8 9 , "
TURN SIGNAL AND HAZARD WARNING LAMPS" .
Check Horn FunctionAIS004MQ
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-14, "
CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK HORN FUNCTION
Does horn sound with horn switch?
YES or NO
YES >> Horn circuit is OK.
NO >> Check horn circuit. Refer to WW-56, "
HORN" .
Check Headlamp FunctionAIS004MR
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-14, "
CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK HEADLAMP OPERATION
Does headlamp come on when turning lighting switch “ON”?
YES or NO
YES >> Headlamp operation circuit is OK.
NO >> Check headlamp system. Refer to LT- 7 , "
HEADLAMP - XENON TYPE -" .
Check Map Lamp and Ignition Keyhole Illumination FunctionAIS004MS
1. CHECK MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
When map lamp switch is in “DOOR” position, open the front door (LH or RH).
OK or NG
OK >> Replace BCM.
NG >> Check ignition illumination circuit. Refer to LT- 1 5 7 , "
INTERIOR ROOM LAMP" . Map lamp and ignition keyhole illumination should illuminate.

INTELLIGENT KEY SYSTEM
BL-111
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for Steering Lock unitAIS004N1
Terminals and Reference Value for BCMAIS004N2
Terminal
numberWire
colorSignal DesignationMeasuring condition
Standard (V)
Ignition knob
positionOperation or conditions
1 L/R Battery power supply LOCK — Approx. 12
2R/WSteering lock unit
power supplyLOCK — Approx. 5
3R/BSteering lock unit com-
munication signalLOCKPress ignition knob with Intelligent
Key inside vehicle.
Other than the above Approx. 5
4Y/BSteering lock unit
ground—— Approx. 0
SIIA1911J
TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
Approx.
1PUKey ring illumination output sig-
nal Key ring illumination is lighting. Battery voltage
Key ring illumination is being turned off. 0
12 P/BFront door switch (Passenger
side)Door open (ON) → Close (OFF) 0 → Battery voltage
13 P/L Rear door switch RH Door open (ON) → Close (OFF) 0 → Battery voltage
37 B/W Key switchInsert mechanical key from ignition key
sylinder.Battery voltage
Remove mechanical key from ignition
key cylinder.0
38 W/L Ignition switchIgnition switch is in ON or START posi-
tionBattery voltage
39 L CAN-H — —
40 R CAN-L — —
41 R/B Battery saver output signal30 minutes after ignition switch is turned
to OFF0
Ignition switch is in ON position Battery voltage
42 L/R Battery power supply (fuse) — Battery voltage
44 YDriver door lock actuator
(Unlock)Door lock / unlock switch
(Free → Unlock)0 → Battery voltage
45 G/W Left turn signal lampWhen door lock or unlock is operated
using Intelligent Key.*
1
(ON → OFF)Battery voltage → 0
46 BR/W Right turn signal lampWhen door lock or unlock is operated
using Intelligent Key.*
1
(ON → OFF)Battery voltage → 0
47 Y/R Step lamp output signalStep lamp is lighting. 0
Step lamp is being turned off. Battery voltage
48 PU/W Room lamp output signalRoom lamp is lighting.*
20
Room lamp is being turned off.*
2Battery voltage
49 B Ground — 0

INTELLIGENT KEY SYSTEM
BL-145
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
Check Hazard FunctionAIS004NP
1. CHECK HAZARD WARNING LAMP
Does hazard warning lamp flash with hazard switch?
YES or NO
YES >> Hazard warning lamp circuit is OK.
NO >> Check hazard circuit. Refer to LT- 8 9 , "
TURN SIGNAL AND HAZARD WARNING LAMPS" .
Check Horn FunctionAIS004NQ
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-14, "
CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK HORN FUNCTION
Does horn sound with horn switch?
YES or NO
YES >> Horn circuit is OK.
NO >> Check horn circuit. Refer to WW-56, "
HORN" .
Check Headlamp FunctionAIS004NR
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-14, "
CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK HEADLAMP OPERATION
Does headlamp come on when turning lighting switch “ON”?
YES or NO
YES >> Headlamp operation circuit is OK.
NO >> Check headlamp system. Refer to LT- 7 , "
HEADLAMP - XENON TYPE -" .
Check IPDM E/R OperationAIS004NS
1. CHECK IPDM E/R INPUT VOLTAGE
Check voltage between IPDM E/R connector E9 terminal 51 (SB) and ground.
OK or NG
OK >> Replace IPDM E/R.
NG >> GO TO 2.51 (SB) – Ground : Battery voltage
PIIA6403E

BL-192
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for BCMAIS004OY
Terminals and Reference Value for IPDM E/RAIS004OZ
Terminal Wire color Item ConditionVoltage (V)
(Approx.)
11 L G / RACC power supply
(ACC or ON)Ignition switch (ACC or ON position) Battery voltage
12 P/BFront door switch
passenger side signalON (Open) → OFF (Closed) 0 → Battery voltage
13 P/L Rear door (RH) switch signal ON (Open) → OFF (Closed) 0 → Battery voltage
22 OR Power window serial linkIGN SW ON or power window timer
operating
23 G/OR Security indicator lamp Goes off → Illuminates Battery voltage → 0
39 L CAN-H — —
40 R CAN-L — —
42 L/R Battery power supply — Battery voltage
49 B Ground (signal) — 0
52 B Ground (power) — 0
55 G Battery power supply — Battery voltage
58 L Back door switch signal ON (Open) → OFF (Closed) 0 → 9
62 WFront door switch
driver side signalON (Open) → OFF (Closed) 0 → Battery voltage
63 P Rear door (LH) switch signal ON (Open) → OFF (Closed) 0 → Battery voltage
PIIA2344J
Terminal Wire color Item ConditionVoltage (V)
(Approx.)
20 LG Headlamp low (RH)Lighting switch 2ND position
ON → OFFBattery voltage → 0
27 BR Headlamp high (RH)Lighting switch HIGH or PASS position
ON → OFFBattery voltage → 0
28 SB Headlamp high (LH)Lighting switch HIGH or PASS position
ON → OFFBattery voltage → 0
30 GY Headlamp low (LH)Lighting switch 2ND position
ON → OFFBattery voltage → 0
38 B Ground (power) — 0
48 L CAN-H — —
49 R CAN-L — —
51 SB Horn relay control signalPanic alarm is operating 0
Other than above Battery voltage
56 LG Hood switch signal ON (Open) → OFF (closed) 0 → Battery voltage
60 B Ground (signal) — 0